Recently, the combination of press-fit acetabular cup with ceramic articulation is a widely used for implanting cementless acetabular components and has been shown to provide good initial stability. However, these methods may lead to elevating stresses, changing in the bearing geometries, and increasing wear due to deformation of the cup and insert. In addition, there is a potential for failure of ceramic inserts when a large ball head was used because it should be assembled with shallow thickness of the acetabular cup. For risk reduction of it, we applied direct metal tooling (DMT) based on 3D printing for porous coating on the cup. Due to its capability of mechanical strength, DMT coated cup could be feasible to provide better stability than conventional coating. Therefore, we constructed laboratory models for deformation test simulating an press-fit situation with large ceramic ball head to evaluate stability of the DMT coated cup compared with conventional coated cup. The deformation test was performed according to the test setup described by Z. M. Jin et al. The under reaming of the cavity in a two-point pinching cavity models of polyurethane (PU) foam block (SAWBONES, Pacific Research Laboratories, USA) with a grade 30 were constructed. Titanium plasma spray (TPS) and direct metal tooling (DMT) coated acetabular cups (BENCOX Mirabo and Z Mirabo Cup, Corentec Co. Ltd., KOREA) with a 52 mm size (n=3, respectively) were used for the test. These cups were implanted into the PU foam blocks, and followed by impaction of the inserts (BIOLOX delta, Ceramtec, GE) with a 36/44 size (n=6) into the acetabupar cups as shown in Fig. 1. Roundness and inner diameter of the acetabular cups and inserts were measured using a coordinate measuring machine (BHN 305, Mitutoyo Neuss, GE) in three levels; E2, E3, and E4 (3, 5, and 7 mm below the front face, respectively). Also, these parameters of the acetabular cup were measured in two level; E1 and E5 (5 and 11 mm below the front face) as shown in Fig. 2. Changes in roundness and inner diameter of the cup and insert were measured to evaluate deformation in relation to porous coating on the acetabular cups.Introduction
Materials and Methods
The Rotational alignment is an important factor for survival total knee Arthroplasty. Rotational malalignment causes knee pain, global instability, and wear of the polyethylene inlay. Also, the anterior cortex line was reported that more reliable and more easily identifiable landmark for correct tibial component alignment. The aims of the current study is to identify effect of inserting the tibial baseplate of using anterior cortex line landmark of TKA on stress/strain distributions within cortical bone and bone cement. Through the current study, final aim is to suggest an alternative position of tibia baseplate for reduction of TKA failures with surgical convenience. A three-dimensional tibia FE model with TKA was generated based on a traditional TKA surgical guideline. Here, a commercialized TKA (LOSPA, Corentc, Korea) was considered corresponded to a patient specific tibia morphology. Tibia baseplate was positioned at anterior cortex line. Alternative two positions were also considered based on tibia tuberosity 1/3 line and tibia tuberosity end line known as a gold standard Introduction
Materials and Method
Revision total knee arthroplasy (TKA) has been often used with a metal block augmentation for patients with poor bone quality. However, bone resorption beneath metal block augmentation has been still reported and little information about the reasons of the occurrence of bone resorption is available. The aim of the current study is to identify a possibility of the potential occurrence of bone resorption beneath metal block augmentation, through evaluation of strain distribution beneath metal block augmentation in revision TKA with metal block augmentation, during high deep flexion. LOSPA, revision TKA with a metal block augmentation (Baseplate size #5, Spacer size #5, Stem size Φ9, L30, Augment #5 T5) was considered in this study. For the test, the tibia component of LOSPA was implanted to the tibia sawbone (left, #3401, Sawbones EuropeAB, Malmö, Sweden), which was corresponded to a traditional TKR surgical guideline. The femoral component of LOSPA was mounted to a customized jig attached to the Instron 8872 (Instron, Norwood, MA, USA), which was designed specially to represent the angles ranged from 0° to 140° with consideration of a rollback of knee joint (Figure. 1). Here, a compressive load of 1,600N (10N/s) was applied for each angle. Strain distribution was then measured from rossete strain gauge (Half Bridge type, CAS, Seoul, Korea) together (Figure 1).Introduction
Materials and Method
Unicompartmental knee arthroplasty (UKA) is often considered to be attractive alternate surgical technique to total knee arthroplasty (TKA) and high tibial osteotomy (HTO), in particular young patients. In addition, it is recently reported that preservation of joint line in UKA is crucial factor for positive long-term outcome, especially in revision case for UKA. However, the role of this joint line has neither been invested nor is it consciously bothered during surgical implantation. Validated finite element (FE) analysis was introduced in this study to investigate the effects of maximum contact stress on polyethylene (PE) insert and maximum compressive stress in opposite compartments for joint line in fixed-type UKA. As suggested by Weber et al., FE model for joint line was developed by means of determination of the angle between the pre-operative joint line and the reference line from lateral cortical is of the femur. Based on the method above, joint lines were modeled in −3, −2, −1, 0, +1, +2, and +3 mm cases and these seven FE models were compared and analyzed (Fig. 1). All implant components were modeled as linear elastic isotropic materials. However, the model was considered to have plastic characteristics of PE insert. FE analysis was performed using high kinematics displacement and rotation inputs, which were based on the kinematics of the natural knee. ISO standards were used for axial load and flexion (Fig. 2). The FE model was subjected to validation based on cadaveric experimental data available in the literature by Sohn et al. and from previous cadaveric tests conducted by current investigators. The maximum contact stress was found at around 43 % of the gait cycle in 0 mm case. There were no difference between ± 1 and 0 mm cases, but maximum contact stress on PE insert becomes greater in ± 3 mm cases. The maximum compressive stress of the lateral meniscus in 0 mm case occurred at 62 % of the gait cycle. There were no difference in positive joint line cases in maximum compressive stress, however maximum compressive stress of the lateral meniscus becomes greater in - 3 mm cases. This study emphasized the importance of joint line preservation after implantation of UKA. It would be critical to determine the joint line in UKA surgery in future based on the result showing that there has been no remarkable difference in stress but changed rapidly from the position beyond the joint line. In future study, it would be valuable study to compare between joint lines of fixed- and mobile-type UKA.
Cementless arthroplasty has been widely used for younger patients with osteoarthritis and other joint pathology. Cementless arthroplasty will be required to porous surface which is to similar to the trabecular bone for bone ingrowth. Titanium Plasma Spray (TPS) has been worldwide used for the porous coating method on arthroplasty. However, TPS coating is limited that would not to establish optimal porosity for bone ingrowth due to arbitary position of melted powder by plasma gas on substrate. Therefore, it is reported coating detached from its substrate (i.e. arthroplasty) is induced implant loosening. Thus, a novel Laser-aided Direct Metal Tooling (DMT) based on Additive Manufacturing (AM) was developed to overcome these limitations. In this study, we were done to assess stereological analysis, static tensile, shear, abrasion test, and physical analysis for evaluation of the efficacy of DMT which was newly-developed coating technology. Then, mechanical characteristics of DMT coating were compared to commercial TPS coating's. First, porosity of the DMT coating was evaluated using Microphotography and Scanning Electron Microscopy (SEM), as described in Figure 1. Static tensile and shear test for assessment of mechanical characteristic in relation to the DMT and TPS coating specimens were conducted on the basis of ASTM F1147 and F1044 using universal testing machine (Endolab®, Servohydraulic Test Frame, DE). Maximum tensile strength and maximum shear strength were evaluated for each specimen (n=5). Abrasion test was performed based on ASTM F1978 using Taber® Rotary Platform Abraser Model 5135 (TABER®Industries, USA). Abrasion losses for each specimen (n=6) were measured at 2, 5, 10, and 100 cycles, respectively.Introduction
Materials and Methods
Revision total knee arthroplasty (TKA) has been often used with a metal block augmentation for patients with poor bone quality. However, bone defects are frequently detected in revision TKA used with metal block augmentation. This study focused on identification of a potential possibility of the bone defect occurrence through the evaluation of the strain distribution on the cortical bone of the tibia implanted revision TKA with metal block augmentation, during high deep flexion. Composite tibia finite element (FE) model was developed and revision TKA FE model with a metal block augmentation (Baseplate size #5 44AP/67ML, Spacer size #5 44AP/67ML, Stem size Φ9, L30, Augment #5 44AP/67ML thickness 5mm) was integrated with the composite tibia FE model. 0°, 30° 60°, 90°, 120° and 140° flexion positions were then considered with femoral rollback phenomenon [Introduction
Materials and Methods
This prospective study was undertaken to compare the clinical and radiological results and the in vivo stabilities of anteromedial (AM) and posterolateral (PL) bundle augmentation during anterior cruciate ligament (ACL) reconstruction. Forty-two ACL partial tears that underwent isolated bundle augmentation (22 AM and 20 PL bundles) were evaluated with a minimum follow-up of 1 year. For in vivo intraoperative stability testing, anteroposterior and external/internal rotation stabilities were measured at 0, 30, 60, and 90° of flexion using a navigation system. Ranges of motion, Lachman and pivot shift test results, Tegner activity scores, and Lysholm knee scores of the AM and PL bundle groups were compared. In addition, Telos arthrometer determined stabilities were compared. In-vivo intraoperative stability testing showed that mean preoperative anterior translation at 30° of flexion was greater in the AM group (8.7 vs. 6.5, p = 0.04), whereas mean rotational amount was larger in the PL group (by 2.9 at 0° and 3.6 at 30° of flexion). After ACL reconstruction, no significant differences were found between the two groups in terms of anterior and rotational stabilities at any flexion angle. Furthermore, clinical outcomes in the two groups were not significantly different. Lachman and pivot shift test results and instrumented laxity findings were similar for the two groups at final follow up. In this study, the authors carefully preserved the remnant injured ACL, and achieved excellent anterior stability recoveries and good rotatory stabilities. No significant intergroup difference was found in terms of intraoperative stability or clinical parameters after ACL reconstruction.
The purpose of this study were to evaluate early intra-operative experiences of a custom-fit total knee arthroplasty (TKA) system and to determine the precision of long leg alignment and component placement achieved using this system. Seventeen patients underwent sagittal MRI of an arthritic knee to determine component placement for TKA from October 2010 and March 2011. Cutting guides were machined to control all intra-operative cuts, and cutting guide placements were recorded by navigation system. Radiographic parameters regarding mechanical axis changes, and inclinations of the femoral and tibial components were measured. Outcome was defined as “excellent” when values of each parameters were within ± 2°, as “acceptable” when within ± 3°, and as “outliers” when >± 3° of optimum. The cutting guide placement was within ±2° of the target angle for inclinations of femoral and tibial components. The cutting heights were within 2mm for distal femoral and proximal tibia. Mechanical axis changed from a mean of 8.57° varus to 0.49° valgus, and mean coronal inclinations of femoral and tibial components were 89.52° and 90.12°, respectively, at last follow up visits. There were no outliers and all of them were classified as excellent. Mean sagittal inclinations of the femoral and tibial components were 1.06° and 84.56°, respectively. There were no intra-operative or acute post-operative complications. The custom-fit TKA system system provides an effective, safe means of achieving an accurate mechanical axis and of reducing prosthetic alignment outliers. However, further long term follow-up is needed.
The elevation of the joint line is considered a possible cause of mid-flexion instability in total knee arthroplasty (TKA). The authors evaluated the effects of joint line change on mid-flexion stability in cruciate retaining TKA. Seventy-nine knees treated by cruciate retaining TKA using a modified balanced gap technique were included in this prospective study. After prosthesis insertion, valgus and varus stabilities were measured under valgus and varus stress using a navigation system at 0, 30, 60 and 90° of knee flexion. Changes of joint lines were measured preoperatively and postoperatively and compared. The knees were allocated to a “No change group (≤4mm, 62 patients)” or to an “Elevation group (>4mm, 17 patients)”. Medio-lateral stabilities (defined as the sums of valgus and varus stabilities measured intra-operatively) were compared in the two groups. The mean joint line elevation was 4.6mm in the no change group and 1.7mm in the elevation group. Mean medio-lateral stability at 30° of knee flexion was 4.8±2.3 mm in the no change group and 6.3±2.7 mm in the elevation group, and these values were significantly different (p = 0.02). However, no significant differences in medio-lateral stability were observed at other flexion angles (p>0.05). Knees with a < 5mm joint line elevation provide better mid-flexion stability after TKA. The results of this study suggest that a < 5mm elevation in joint line laxity is acceptable for cruciate retaining TKA.
This study was performed to measure intra-operative varus-valgus laxities from 0° to 90° of flexion during cruciate retaining total knee arthroplasty (TKA) using the modified balanced gap technique. Forty nine patients awaiting unilateral TKA for osteoarthritis were enrolled into this prospective study. Flexion and extension gaps were measured at full extension and at 90° of flexion using a tensioning device before femoral bone cutting. After implantation and closing the medial parapatellar arthrotomy, varus-valgus laxities at 0, 30, 60 and 90° of flexion were also measured using a navigation system. Mean total varus-valgus laxities were significantly less at 0° of flexion (3.8±1.7°) than at the other selected flexion angles. Mean varus laxity was peaked at 3.1±2.2° at 60° of flexion and reached a nadir of 2.0±1.0° at 0° of flexion, which represented a significant difference. On increasing flexion from 0° to 60°, mean valgus laxity increased from 1.8±1.3° to 2.9±1.6°, which was significant, but no significant difference was found for other angles. The use of the balanced gap technique for cruciate retaining TKA using a navigation system, which allows accurate soft tissue balancing via real time gap size feedback, could be helpful for achieving good in vivo laxities throughout range of motion without significant mid flexion laxity.
Recently, axial radiography has received attention for the assessment of distal femur rotational alignment, and satisfactory results have been as compared with the CT method. The purpose of this study was to assess rotational alignment of the femoral component in knee flexion by axial radiography and to compare flexion stabilities achieved by navigational and robotic total knee arthroplasty (TKA). In addition, the authors also evaluated the effects of flexion stability on functional outcomes in these two groups. Sixty-four patients that underwent TKA for knee osteoarthritis with a minimum of follow-up of 1 year constituted the study cohort. Patients in the navigational group (N = 32) underwent TKA using the gap balancing technique and patients in the robotic group (N = 32) underwent TKA using the measured resection technique. To assess flexion stability using axial radiography a novel technique designed by the authors was used. Rotations of femoral components and mediolateral gaps in the neutral position on flexion radiographs was measured and compared. Valgus and varus stabilities under valgus-varus stress loading, and total flexion stabilities (defined as the sum of valgus and varus stability) were also compared, as were clinical outcomes at final follow up visits. A significant difference was found between the navigation and robotic groups for mean external rotation of the femoral component (2.1° and 0.4°, respectively; Both navigational and robotic techniques provide excellent clinical and flexion stability results. Furthermore, axial radiography was found to provide a useful, straightforward means of detecting rotational alignment, flexion gaps, and flexion stability.
The purpose of this study was to compare posterior tibial slope preoperatively and postoperatively in patients undergoing navigational opening-wedge High tibial osteotomy (HTO) and to compare posterior slope changes for 2 and 3-dimentional (D) navigation versions. Between May 2009 and September 2010, 35 patients with unicompartmental osteoarthritis and varus deformity were treated by navigation-assisted open-wedge HTO. Patients were randomly divided into two groups according to the version of the Orthopilot (Aesculap) navigation system used; 2D group (18 patients, 2-D version) and 3D group (17 patients, 3-D version). Radiologic evaluations were conducted using pre- and postoperative leg axes. Posterior slope of proximal tibiae were measured using the proximal tibial anatomic axis method. Postoperatively the mechanical axis was corrected adequately to a mean valgus of 2.81° in 2D group and of 3.15° in 3D group. Mean posterior slopes were well maintained, and measured 7.9° and 10.3° preoperatively and 8.99° and 9.14° postoperatively in 2D and 3D groups, respectively. No significant difference was found between the two navigation versions with respect to posterior tibial slope; mean tibial slope changes were 1.09° and −0.2° in 2D and 3D groups ( Navigation-assisted opening-wedge HTO greatly improves the accuracy of the desired postoperative mechanical femorotibial axis and posterior tibial slope, and the use of 3D navigation results in significantly less change in posterior tibial slope. The authors recommend the use of the 3D navigation because they provide real time intraoperative information about coronal, sagittal, and transverse axis, which are important for the maintenance of a normal posterior tibial slope.
The preoperative prediction of gap balance after robotic total knee arthroplasty (TKA) is difficult. The purpose of this study was to evaluate the effectiveness of a new method of achieving balanced flexion-extension gaps during robotic TKA. Fifty one osteoarthritic patients undergoing cruciate retaining TKA using robotic system were included in this prospective study. Preoperative planning was based on the amount of lateral laxity in extension and flexion using varus stress radiograph. After complete milling by the robot and soft tissue balancing, intra-operative extension and flexion gaps were measured using a tensioning device. Knees were subdivided into three groups based on lateral laxities in 0° and 90° of flexion, as follows; the tight extension group (≥ 2mm smaller in extension than flexion laxity), the tight flexion group (≥ 2mm smaller in flexion than extension laxity), and the balanced group (< 2mm difference between laxities). In addition, intra-operative gap balance results were classified as acceptable (0–3mm larger in flexion than in extension), tight (larger in extension than in flexion) or loose (> 3mm larger in flexion than in extension) based on differences between extension and flexion gaps. During preoperative planning, 34 cases were allocated to the balanced group, 16 to the tight extension group and 1 case was allocated to the tight flexion group. Intra-operative gap balance was acceptable in 46 cases, 4 cases had a tight result, and one case had a loose flexion gap. We concluded that preoperative planning based on the amount of lateral laxity determined using varus stress radiographs may be useful for predicting intraoperative gap balance and help to achieve precise gap balance during robotic TKA.
