Introduction. Tibiofemoral constraint in patients with total knee replacements (TKR) is dependent on both implant geometry and the surrounding soft tissue structures. Choosing more highly constrained geometries can reduce the contribution of soft tissue necessary to maintain joint stability [1]. Often when knee revision surgeries are required, the soft tissue and bone are compromised leading to the use of more constrained implants to ensure knee stability [2]. The current study quantifies the differences in varus-valgus (VV) and internal-external (IE) constraint between two types of total knee revision systems: SIGMA® TC3© and ATTUNE® REVISION. Methods. Nine cadaveric knees (7 male, age 64.0 ± 9.8 years, BMI 26.28 ± 4.92) were implanted with both fixed-bearing SIGMA TC3 and ATTUNE REVISION knee systems. Five knees received the TC3 implant first, while the remaining 4 received the ATTUNE implant first. The knees were mounted in an inverted position, and a six degree-of-freedom force-torque sensor (JR3, Woodland, CA) was rigidly secured to the distal tibia (Fig. 1). A series of manual manipulations applying IE and VV torques was performed through the flexion range [3]. Each specimen was then revised to the alternate revision system, and the manual manipulations were repeated. Joint loads were calculated, and tibiofemoral kinematics were described according to the Grood-Suntay definition [4]. VV and IE kinematics were calculated as a function of flexion angle, VV torque, and IE torque as has been described previously [3]. The knees were analysed at ±6 Nm VV and ±4 Nm IE, and the kinematics were normalized to the zero load path. A paired t-test (p < .05) was employed to identify significant differences between the kinematics of the two knee systems at 10º flexion increments. Results. Less VV motion was observed in the ATTUNE REVISION system compared to the TC3 system reaching statistical significance in mid-flexion. (Fig. 2). No significant differences were observed in IE rotation between the two designs, except in full extension where the SIGMA TC3 provided increased constraint (Fig. 3). Discussion. The ATTUNE REVISION System provided increased VV constraint compared to the TC3 design. The ATTUNE tibial post was more conforming to the femoral box throughout flexion, which contributed to the increased constraint. However, this increase was not concurrent with a reduction in IE rotational freedom as has been common with more constrained revision systems [5]. ATTUNE REVISION provides additional VV stability while retaining knee IE freedom and, therefore, may enable more natural knee kinematics for patients with MCL deficiency in need of a revision TKR. Future work will focus on how the increased levels of VV constraint affect weight-bearing knee kinematics in the presence of ligament deficiency. Acknowledgements. This work was supported by DePuy Synthes Joint Reconstruction, Warsaw, Indiana, a Johnson and Johnson Company. For figures and references – please contact authors directly

Introduction. Patellar crepitus and clunk are tendofemoral-related complications predominantly associated with posterior-stabilizing (PS) total knee arthroplasty (TKA) designs [1]. Contact between the quadriceps tendon and the femoral component can cause irritation, pain, and catching of soft-tissue within the intercondylar notch (ICN). While the incidence of tendofemoral-related pathologies has been documented for some primary TKA designs, literature describing revision TKA is sparse. Revision components require a larger boss resection to accommodate a constrained post-cam and stem/sleeve attachments, which elevates the entrance to the ICN, potentially increasing the risk of crepitus. The objective of this study was to evaluate tendofemoral contact in primary and revision TKA designs, including designs susceptible to crepitus, and newer designs which aim to address design features associated with crepitus. Methods. Six PS TKA designs were evaluated during deep knee bend using a computational model of the Kansas knee simulator (Figure 1). Prior work has demonstrated that tendofemoral contact predictions from this model can differentiate between TKA patients with patellar crepitus and matched controls [2]. Incidence of crepitus of up to 14% has been reported in Insall-Burstein® II and PFC® Sigma® designs [3]. These designs, in addition to PFC® Sigma® TC3 (revision component), were included in the analyses. Primary and revision components of newer generation designs (NexGen®, Attune® and Attune® Revision) were also included. Designs were evaluated in a patient model with normal Insall-Salvati ratio and a modified model with patellar tendon length reduced by two standard deviations (13mm) to assess worst-case patient anatomy. Results. During simulations with normal patellar tendon length, only PFC® Sigma® and PFC® Sigma® TC3 showed tendofemoral contact within the trochlea, and no design showed contact at the transition to the ICN (Figure 2). In simulations with patella baja, Insall-Burstein® II, PFC® Sigma®, and PFC® Sigma® TC3, demonstrated tendofemoral contact across the trochlea at the transition into the notch. In contrast, NexGen®, Attune® and Attune® Revision showed tendon contact for approximately half the width of the transition to the notch (Figure 3). PFC® Sigma® and Attune® demonstrated very similar tendofemoral contact to their equivalent revision components, although the shorter trochlear groove of Attune® Revision marginally increased contact at the transition. Discussion. Insall-Burstein® II, PFC® Sigma®, and PFC® Sigma® TC3 designs showed full contact with the quadriceps tendon at the anterior border of the ICN when combined with a short patellar tendon. NexGen®, Attune® and Attune® Revision had a more gradual transition between the trochlea and the notch, which resulted in less exposure to tendon contact. Even with the shorter trochlear groove required for revision components, Attune® Revision showed minimal difference in tendofemoral contact when compared with Attune®. There appears to be distinct benefit in a femoral design which reduces tendofemoral contact at the transition to the ICN; this may be of particular importance for patients with patella baja

Introduction. Previous fluoroscopy studies have been conducted on numerous primary-type TKA, but minimal in vivo data has been documented for subjects implanted with revision TKA. If a subject requires a revision TKA, most often the ligament structures at the knee are compromised and stability of the joint is of great concern. In this present study, subjects implanted with a fixed or mobile bearing TC3 TKA are analyzed to determine if either provides the patient with a significant kinematic advantage. Methods. Ten subjects are analyzed implanted with fixed bearing PFC TC3 TKA and 10 subjects with a mobile bearing PFC TC3 TKA. Each subject underwent a fluoroscopic analysis during four weight bearing activities: deep knee bend (DKB), chair rise, gait, and stair descent. Fluoroscopic images were taken in the sagittal plane at 10 degree increments for the DKB, 30 degree increments for chair rise, and at heel strike, toe off, 33% and 66% cycle gait and stair descent. Results. The average weight bearing maximum flexion for the fixed bearing TKA group was 104 degrees (SD = 18.2 degrees). The average medial and lateral anterior-posterior (AP) translation for these subjects from full extension to maximum weight-bearing flexion was −6.74 mm and −8.0 mm in the posterior direction, respectively. The average femorotibial axial rotation was 1.27 degrees from full extension to maximum flexion. The average medial and lateral AP translations respectively from full extension to maximum flexion are shown in Figures 1 and 2 and the corresponding average femorotibial axial rotation pattern is shown in Figure 3. Subjects implanted with a mobile bearing device are presently being analyzed. Discussion. The fixed bearing device, on average, does not allow for much axial rotation when compared to less constrained or mobile bearing TKA designs. Previous studies have mobile bearing rotating platform primary posterior stabilized devices have documented that the bearing does rotate with the femur. Therefore, it is assumed subjects having a mobile bearing TC3 TKA may achieve greater axial rotation. Subjects having the fixed bearing TC3 TKA did achieve posterior femoral rollback of both condyles, revealing that a fixed bearing revision TKA may act more like a hinged device

Introduction. We aim to assess the functional outcome, patient perceived satisfaction and implant survival at a mean follow up of 13[10–16] years following revision knee replacement. Patients and Methods. Between 1995 and 2001, 243 revision knee replacements were performed in 230 patients using Endolink [Link, Hamburg] or TC3 [Depuy, Leeds] prosthesis at Wrightington hospital, Wrightington, were consented to take part in this study. Data was collected prospectively which includes complications and functional assessment by Oxford knee score, WOMAC, HSS, UCLA, SF12 scores, and patient satisfaction questioner. The scores were obtained pre-operatively and post-operatively at 1 year, 5 years and at the latest follow-up. The mean age was 69 yrs, 51% were males, TC3 prosthesis as used in 175 and Endolink in 68, the revision was for Infection in 71[29%], 53 patients had intra-operative positive culture, 35 had 2 stage revision. Results. At a mean follow up of 13 years [10–16] the survival of revision knee replacement in our patient group is 86%. Further surgery was performed in 35[14%], which includes 5 patients who had above knee amputation. The re-revision rate in the non-infected group [13%] was significantly lower compared to the re-revision in infected group [18%]. The Oxford scores improved at 1 year which continued to improve up to 5 years following which there was a gradual deterioration in the scores. There was no significant improvement in the generic HSQ, SF12 and UCLA scores following surgery. The functional scores improved to a lesser extent in patients with proven infection. Discussion and Conclusion. At a mean follow up of 13 years the implant survival for revision knee replacement using endolink or TC3 prosthesis is 86%. The non-infected group had lower re-revision rates. The improvement in functional scores is lower following revision for infection

Introduction. Electromyography (EMG) is the best known method in obtaining in vivo muscle activation signals during dynamic activities, and this study focuses on comparing the EMG signals of the quadriceps muscles for different TKA designs and normal knees during maximum weight bearing flexion. It is hypothesized that the activation levels will be higher for the TKA groups than the normal group. Methods. Twenty-five subjects were involved in the study with 11 having a normal knee, five a rotating platform (RP) posterior stabilized (PS) TKA, and nine subjects with a PFC TC3 revision TKA. EMG signals were obtained from the rectus femoris, vastus medialis, and vastus lateralis as the patients performed a deep knee bend from full extension to maximum flexion. The data was synchronized with the activity so that the EMG data could be set in flexion-space and compared across the groups. EMG signals were pre-processed by converting the raw signals into neural excitations and normalizing this data with the maximum voluntary contraction (MVC) performed by the subject. The signals were then processed to find the muscle activations which, normalized by MVC, range from 0 to 1. Results. The average muscle activations for each of the three groups are shown in Figures 1, 2, and 3 for the rectus femoris, vastus medialis, and vastus lateralis respectively. The vastus medialis had the highest activation of the muscles during the weight bearing activity from 0 to 90 degrees flexion. On average, the trend seen is that the normal group had lower muscle activation levels to perform the weight bearing activity as opposed to the TKA groups which supports our hypothesis. The PS RP TKA had lower peak values than the PFC TC3 TKA. Discussion. EMG analysis provides insight into muscle activation during dynamic activities. When designing TKA devices for implantation, the patient themselves must be taken into account. In a subject with deficient ligaments, a more constrained device can make day-to-day activities easier, but at the expense of extra effort in achieving higher flexion activities. The high constraints within the PFC TC3 may cause the patient to have to put more effort into the activity. The rotating platform TKA had closer to normal muscle activation levels for the maximum weight bearing knee flexion activity

INTRODUCTION. Modular knee implants are used to manage large bone defects in revision total knee arthroplasty. These implants are confronted with varying fixation characteristics, changes in load transfer or stiffen the bone. In spite of their current clinical use, the influence of modularity on the biomechanical implant-bone behavior (e.g. implant fixation, flexibility, etc.) still is inadequately investigated. Aim of this study is to analyze, if the modularity of a tibial implant could change the biomechanical implant fixation behavior and the implant-bone flexibility. MATERIAL & METHODS. Nine different stem and sleeve combinations of the clinically used tibial revision system Sigma TC3 (DePuy) were compared, each implanted standardized with n=4 in a total of 36 synthetic tibial bones. Four additional un-implanted bones served as reference. Two different cyclic load situations were applied on the implant: 1. Axial torque of ±7Nm around the longitudinal stem axis to determine the rotational implant stability. 2. Varus-valgus-torque of ±3,5Nm to determine the bending behavior of the stem. A high precision optical 3D measurement system allowed simultaneous measuring of spatial micromotions of implant and bone. Based on these micromotions, relative motions at the implant-bone-interface and implant flexibility could be calculated. RESULTS. Lowest relative micromotions were measured along the tibial base component and the sleeve; however, these motions varied depending on the implant construct used. Maximum relative micromotions were detected at the distal end of the implant for all groups, indicating a more proximal fixation of all modular combinations. Regarding varus-valgus-torque measurement, all groups showed a deviant flexibility behavior compared to the reference group. When referred to the un-implanted bone, implants without stems revealed the highest flexibility, whereas implants with shorter stems had lowest flexibility. DISCUSSION & CONCLUSION. All groups showed a more proximal fixation behavior; moreover, both extent and location of fixation could be influenced by varying the modular combination. Larger stems seemed to support a more distal fixation behavior, whereas the implant fixation moved proximal while extending the sleeve. Here the influence of the sleeve on fixation behavior seemed to be dominant compared to the influence of the stem. Concerning varus-valgus-torque, a strong connection between the used stem and implant-bone flexibility seemed to exist. In addition, the influence of the sleeve on flexibility seemed to be rather low. This study showed, that modularity can influence the biomechanical behavior of tibial implants. If these results can be transferred to other tibial implants still remains to be seen

Purpose. Traditional total knee arthoplasty techniques have involved implantation of diaphyseal stems to aid in fixation expecially when using constrained polyethylene inserts. While the debate over cemented vs uncemented stems continues, the actual use of stems is considered routine. The authors' experience with cemented stemmed knee revisions in older patients with osteoporotic bone has been favorable. Our younger patients with press-fit stems from varying manufacturers have been plagued with a relatively high incidence of component loosening and stem tip pain in the tibia and occasionally thigh. We report the early results of the first 20 total knee revisions using press-fit metaphyseal filling sleeved stemless implants with constrained bearings. Methods. Twenty three patients with failed primary or revision total knees were assigned to receive stemless sleeved revision knee designs using the DePuy MBT/TC3 system. Reasons for revision included loosening, implant fracture, stiffness, instability, and stem pain. Twenty patients (ages ranging from 42–73) were successfully reconstructed without stems. Six knees with significant uncontained cavitary defects were included. Three patients with unexpectedly osteoporotic metaphyseal bone were revised with cemented stemmed implants and excluded. All cases used cement for initial fixation on the cut bone surface and fully constrained mobile bearing inserts. Results. Follow up ranged from six months to three years. All patients had radiographic evidence of well fixed stable implants on most recent examination. All four cases of revision for “end of stem pain” had complete resolution of symptoms within two weeks of revision surgery. Long leg anterior posterior mechanical alignment x-rays measured within two degrees of neutral in all cases. Knee Society Scores improved an average of 34 points. Clinical results for revision for stiffness had the lowest final scores post operatively. Conclusion. Stemmed total knee arthroplasty revision implants with or without cement are considered the standard for most revision reconstructions. Recently, primary total hip replacements using newer short metaphyseal stems have shown promising early clinical results. This case series of twenty total knee revisions using stemless press-fit metaphyseal sleeves shows similarly favorable outcomes. The complications of stemmed implants such as stem tip pain and difficulty of cemented stem removal can be avoided successfully in non-osteporotic bone reconstructions. With stable bony ingrowth visible on early post-operatyive radiographs, long term stable fixation even with constrained bearings is expected. Longer follow up will be needed to validate this technique for routine use