Advertisement for orthosearch.org.uk
Results 1 - 17 of 17
Results per page:
Orthopaedic Proceedings
Vol. 102-B, Issue SUPP_2 | Pages 82 - 82
1 Feb 2020
Zobel S Huber G King M Pfeiffer D Morlock M
Full Access

Introduction. During revision surgery, the active electrode of an electrocautery device may get close to the implant, potentially provoking a flashover. Incidents have been reported, where in situ retained hip stems failed after isolated cup revision. Different sizes of discoloured areas, probably induced by electrocautery contact, were found at the starting point of the fracture. The effect of the flashover on the implant material is yet not fully understood. The aim of this study was to investigate the fatigue strength reduction of Ti-6Al-4V titanium alloy after electrocautery contact. Material and Methods. 16 titanium rods (Ti-6Al-4V, extra low interstitial elements, according to DIN 17851, ⊘ 5 mm, 120 mm length) were stress-relief annealed (normal atmosphere, holding temperature 622 °C, holding time 2 h) and cooled in air. An implant specific surface roughness was achieved by chemical and electrolytic polishing (Ra = 0.307, Rz = 1.910). Dry (n = 6) and wet (n = 6, 5 µl phosphate buffered saline) flashovers were applied with a hand-held electrode of a high-frequency generator (Aesculap AG, GN 640, monopolar cut mode, output power 300 W, modelled patient resistance 500 Ω). The size of the generated discoloured area on the rod's surface - representative for the heat affected zone (HAZ) - was determined using laser microscopy (VK-150x, Keyence, Japan). Rods without flashover (n = 4) served as control. The fatigue strength of the rods was determined under dynamic (10 Hz, load ratio R = 0.1), force-controlled four-point bending (FGB Steinbach GmbH, Germany) with swelling load (numerical bending stress 852 MPa with a bending moment of 17.8 Nm) until failure of the rods. The applied bending stress was estimated using a finite-element-model of a hip stem during stumbling. Metallurgical cuts were made to analyse the microstructure. Results. The control rods failed at the pushers of the setup (median: 94,550, range: 194,000 cycles). The rods with flashover failed directly at the HAZ significantly earlier than the control rods (p = 0.018). The analysis of the microstructure showed a transformation of the equiaxed α+β microstructure to a bimodal state. The size of the HAZs were equal for the dry (median: 1.51 mm. 2. , range: 5.68 mm. 2. ) and wet flashovers (median: 0.92 mm. 2. , range: 2.50 mm. 2. , p = 0.792). The cycles to failure were smaller for the dry flashover (median: 22,650 cycles, range: 5,700) than the wet flashover but not reaching statistical significance (median: 32,200, range: 57,900; p = 0.052). No correlation between the dimension of the HAZs and the cycles to failure was found (dry: r. 2. = 0.019, p = 0.8; wet: r. 2. = 0.015, p = 0.721). Discussion. Flashovers induced by an electrocautery device reduce the fatigue strength of Ti-6Al-4V. Since no correlation between the size of the HAZs and the cycles to failure was found, every contact between electrocautery devices and metal implants should be avoided. For any figures or tables, please contact authors directly


Orthopaedic Proceedings
Vol. 99-B, Issue SUPP_3 | Pages 9 - 9
1 Feb 2017
Aldinger P Pawar V
Full Access

INTRODUCTION. Due to increasing interest into taper corrosion observed primarily in hip arthroplasty devices with modular tapers, efforts towards characterizing the corrosion byproducts are prevalent in the literature [1–4]. As a result of this motivation, several studies postulate cellular induced corrosion due to the presence of remarkable features in the regions near taper junction regions and articulating surfaces [3–5]. Observations made on explanted devices from a retrieval database as well as laboratory tests have led to the alternative proposal of electrocautery-electrosurgery damage as the cause of these features. These surgical instruments are commonly used for hemostasis or different degrees of tissue dissection. METHODS. Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) were used to evaluate the features observed on retrieved devices. Retrieved devices consisted of OXINIUM and cobalt-chromium-molybdenum (CoCrMo) femoral implants, a Titanium-alloy hip stem, and a CoCrMo metal-on-metal femoral head. Electrocautery-electrosurgery damage was created using a SurgiStat II (Valleylab, Colorado) onto various components (CoCrMo, OXINIUM femoral heads as well as Ti-6Al-4V and CoCrMo alloy test stem constructs). Test components were evaluated using the same methods as the retrieved devices. RESULTS. Remarkable features were present on retrieved devices (Figure 1) which were similar to previous studies (3–5). The appearance of these features could be described as crater-like, pitted, scratched, molten or splattered material, and ruffled. These features were present on articulating and non-articulating regions as well as near taper junctions. Testing performed on samples using the SurgiStat II, created features that were similar in appearance (Figure 1). Additionally, material transfer that included an iron peak based on EDS in addition to the cobalt and chromium (present due to native material) was detected in the regions of contact (Figure 2). CONCLUSIONS. It was possible to re-create damage features similar to those previously characterized as remarkable features created by cellular-induced corrosion [3–5]. It is theorized that the high-voltage based electrocautery (commonly Bovie) or high-frequency based electrosurgical devices can result in localized degradation/alteration of oxides and passive regions of commonly used orthopaedic alloys. These surgical instruments, specifically the cutting electrodes, are frequently made of stainless steels which can result in iron transfer during contact with the device. During the surgical use of the electrocautery-electrosurgery instrument, it may be necessary to remove tissue, bone, or cauterize near the implant or explant which may have led to the damage features noted in this study and the previous literature [3–5]. If this damage occurs during the initial implantation of the devices, it may further exacerbate corrosion in the damaged region and/or alter the mechanical integrity of the constructs (i.e. fatigue performance)


Orthopaedic Proceedings
Vol. 105-B, Issue SUPP_3 | Pages 22 - 22
23 Feb 2023
Sandow M Cheng Z
Full Access

Arthroscopic electrosurgical tools for ablative, desiccating or coagulative effect are delivered as monopolar or bipolar probes. Monopolar electrosurgery delivers various profiles of heat energy directly to the tissue within a non-conductive irrigant (such as water or glycine) whereas bipolar electrosurgery creates an energy source by producing an electrical arc between the bipolar electrodes on the instrument head within an electro-conductive irrigation solution (saline) - and the heat generated is then transferred to the target tissues. This study investigated the heat generation within the simulated in-vitro test model to review the level of local heat production and potential local tissue heat.

In a simulated In-vitro testing environment the local heat generation using bipolar or monopolar electrosurgical probes at standard power setting in either saline or water was tested, both touching and not touching a simulated tissue target, and for variable on-times.

Monopolar generated relatively little heat when used in water and not touching the tissue. By contrast the bipolar wand generated potentially damaging local tissue temperature rises when used in saline and not touching the tissue. Both probes generated high local tissue heat when touching the tissue in their recommended irrigation solution.

Monopolar electrosurgery delivered high localized temperature to the simulated tissue surface, but produced relatively little heat when not touching the tissue in a water solution. Bipolar however created high local temperature within the fluid adjacent to the probe irrespective if it was touching the tissue or not. Activation of the bipolar probe away from the tissue in saline irrigation may create a potential harmful temperature within the fluid medium without delivering therapeutic thermal effect to the target tissues. Monopolar electrosurgery appears to deliver a more controlled thermal effect, and only when in contact with the target tissues – potentially creating a reduced collateral thermal footprint.


Orthopaedic Proceedings
Vol. 99-B, Issue SUPP_3 | Pages 57 - 57
1 Feb 2017
Campbell P Yuan N Luck J Courpron P Park S
Full Access

Recently, a special type of surface pitting found on metal implants was proposed to arise from “inflammatory cell-induced” corrosion (ICI, Figure 1) (1, 2). The actual mechanism of this was unknown, but similar features were suggested to be artefacts of electrocautery damage from revision surgery (3). Under lab conditions and without the influence of any cells, we aimed to reproduce the same surface pits and structures with electrocautery. Methods. A polished cobalt-chromium disk (40 mm diameter, 8 mm thick) was marked into 8 sections for various testing conditions (Figure 2a). A stainless steel Bovie tip with a unipolar electrocautery machine (SYSTEM 5000, ConMed, USA) was used at typical surgical coagulation conditions: (70 volt, 120 watts, 562 KHz frequency). We mimicked three types of surgical techniques with the electrocautery: “Dotting” was repeated, on and off, direct surface contact; “Dragging” was constant, direct surface contact; “Hovering” was pausing several millimeters above the surface. We also examined the interplay of these practices on diamond-tip-induced scratches and either dry or wet (normal saline) conditions. High magnification images (Keyence VHX-2000E) were taken after the disk was cleaned with laboratory soap, light mechanical scrubbing, and formalin soak. Results. Coagulation mode generated electrical sparks when dotting/dragging and electrical arcs when hovering. These left seared marks that persisted even after cleaning (Figure 2b). At higher magnification, the surface features were comparable in size and shape to those attributed to ICI (1, 2). Areas wet with saline (Figure 3a) showed an abundance of ringed pits with raised edges that closely resembled those observed in Figure 1. Furthermore we obtained images similar to the phenomenon of “cellular tracks” (Figure 3b) (1). Premade scratches did not influence the pit arrangement but scratches made by the Bovie tip produced the characteristic scratch-associated ICI features as observed on implant retrievals in the past (Figure 3c) (4). Discussion. In the absence of cells, pitting equivalent to proposed ICI features was successfully replicated using an electrocautery in coagulation mode. Previously (4), we found a high incidence but small surface area of these features on the majority of retrievals, predominantly located in a focal area of the superior aspect of the femoral ball next to the junction of the stem. There were fewer on the inferior aspect which is consistent with electocautery damage when dissecting the hip capsule. The effect of this damage on retained parts is unknown, but electrocautery damage around areas of implant fractures has been reported (3). Conclusion. The striking similarities of the recreated pit structures imaged here suggest that the noted features of “inflammatory cell induced corrosion” were artefacts of the electrocautery during revision surgery. Future implant retrieval analysis should acknowledge these structures are not related to any particular mode of failure but should check for them around implant fracture sites


Bone & Joint Open
Vol. 1, Issue 6 | Pages 309 - 315
23 Jun 2020
Mueller M Boettner F Karczewski D Janz V Felix S Kramer A Wassilew GI

Aims. The worldwide COVID-19 pandemic is directly impacting the field of orthopaedic surgery and traumatology with postponed operations, changed status of planned elective surgeries and acute emergencies in patients with unknown infection status. To this point, Germany's COVID-19 infection numbers and death rate have been lower than those of many other nations. Methods. This article summarizes the current regimen used in the field of orthopaedics in Germany during the COVID-19 pandemic. Internal university clinic guidelines, latest research results, expert consensus, and clinical experiences were combined in this article guideline. Results. Every patient, with and without symptoms, should be screened for COVID-19 before hospital admission. Patients should be assigned to three groups (infection status unknown, confirmed, or negative). Patients with unknown infection status should be considered as infectious. Dependent of the infection status and acuity of the symptoms, patients are assigned to a COVID-19-free or affected zone of the hospital. Isolation, hand hygiene, and personal protective equipment is essential. Hospital personnel directly involved in the care of COVID-19 patients should be tested on a weekly basis independently of the presence of clinical symptoms, staff in the COVID-19-free zone on a biweekly basis. Class 1a operation rooms with laminar air flow and negative pressure are preferred for surgery in COVID-19 patients. Electrocautery should only be utilized with a smoke suction system. In cases of unavoidable elective surgery, a self-imposed quarantine of 14 days is recommended prior to hospital admission. Conclusion. During the current COVID-19 pandemic, orthopaedic patients admitted to the hospital should be treated based on an interdisciplinary algorithm, strictly separating infectious and non-infectious cases. Cite this article: Bone Joint Open 2020;1-6:309–315


Orthopaedic Proceedings
Vol. 101-B, Issue SUPP_8 | Pages 48 - 48
1 May 2019
Lombardi A
Full Access

The battle of revision TKA is won or lost with safe, effective, and minimally bony-destructive implant removal, protecting all ligamentous stabilisers of the knee and, most importantly, the extensor mechanism. For exposure, incisions should be long and generous to allow adequate access. A standard medial parapatellar capsular arthrotomy is preferred. A synovectomy is performed followed by debridement of all scar tissue, especially in the medial and lateral gutters. All peripatellar scar tissue is excised followed by release of scar tissue within the patellar tendon, allowing for displacement or everting of the patella. As patellar tendon avulsion at any time of knee surgery yields disastrous results, the surgeon should be continuously evaluating the patellar tendon integrity, especially while displacing/everting the patella and bringing the knee into flexion. If displacement/eversion is difficult, consider rectis-snip, V-Y quadricepsplasty, or tibial tubercle osteotomy. The long-held requisite for patellar eversion prior to component removal is inaccurate. In most cases simple lateral patellar subluxation will provide adequate exposure. If a modular tibial system is involved, removal of the tibial polyethylene will decompress the knee, allowing for easier access to patellar, femoral, and tibial components. For patellar component removal, first identify the border of the patella, then carefully clean and debride the interface, preferably with electrocautery. If the tibial component is cemented all-polyethylene, remove using an oscillating saw at the prosthetic-bone interface. Debride the remaining cement with hand tools, ultrasonic tools, or burrs. Remove the remaining peg using a low-speed burr. If the tibial component is metal-backed, then utilise a thin saw blade or reciprocating saw to negotiate the undersurface of the component between the pegs. If pegs are peripherally located, cut with a diamond disc circular cutting tool. Use a trephine to remove the pegs. For femoral component removal, identify the prosthetic-bone/prosthetic-cement interface then remove soft tissue from the interface, preferably with electrocautery. Disrupt the interface around all aspects of the component, using any of following: Gigli saw for cementless components only, micro saw, standard oscillating saw, reciprocating saw, a series of thin osteotomes, or ultrasonic equipment. If the femoral component is stemmed, remove the component in two segments using an appropriate screwdriver to remove the screw locking the stem to the component. Remove the femoral component with a retrodriver or femoral component extractor. Debride cement with hand tools or burr, using care to avoid bone fracture. If a stem is present, then remove with the appropriate extraction device. If “mismatch” exists, where femoral (or likewise, tibial) boss is smaller in diameter than the stem, creating a cement block prohibiting stem removal, remove the cement with hand tools or burr. If the stem is cemented, use hand tools, ultrasonic tools, or a burr to debride the cement. Curette and clean the canals. For tibial component removal, disrupt the prosthetic-cement/prosthetic-bone interface using an oscillating or reciprocating saw. Gently remove the tibial component with a retrodriver or tibial extractor. If stem extensions are utilised, disengage and debride all proximal cement prior to removing the stem. If stem is present, then remove stem with appropriate extraction device. If stem is grit-blasted and well-fixed, create 8mm burr holes 1.5 to 2.5cm distal to tibial tray on medial aspect and a small divot using burr, then drive implant proximally with Anspach punch. Alternatively, a tibial tubercle osteotomy may be performed. If the stem is cemented, use hand tools, ultrasonic tools or burr to debride cement


Orthopaedic Proceedings
Vol. 99-B, Issue SUPP_3 | Pages 19 - 19
1 Feb 2017
Arnholt C MacDonald D Lowell J Gilbert J Mihalko W Kurtz S
Full Access

Introduction. Previous studies of CoCr alloy femoral components for total knee arthroplasty (TKA) have identified 3. rd. body abrasive wear, and apparent inflammatory cell induced corrosion (ICIC) [1] as potential damage mechanisms. The association between observed surface damage on the femoral condyle and metal ion release into the surrounding tissues is currently unclear. The purpose of this study was to investigate the damage on the bearing surface in TKA femoral components recovered at autopsy and compare the damage to the metal ion concentrations in the synovial fluid. Methods. 12 autopsy TKA CoCr femoral components were collected as part of a multi-institutional orthopedic implant retrieval program. The autopsy components included Depuy Synthes Sigma Mobile Bearing (n=1) and PFC (n=1), Stryker Triathlon (n=1) and Scorpio (n=3), and Zimmer Nexgen (n=4) and Natural Knee (n=2). Fluoro scans of all specimens prior to removal was carried out to assure no signs of osteolysis or aseptic loosening were present. Third-body abrasive wear of CoCr was evaluated using a semi-quantitative scoring method similar to the Hood method [2]. ICIC damage was reported as location of affected area and confirmed using a digital optical microscope with 4000X magnification. Synovial fluid was aspirated from the joint capsule prior to removal of the TKA device. The synovial fluid was spun at 1600 rpm for 20 minutes in a centrifuge with the cell pellet removed. The supernatant was analyzed in 1 mL quantities for ICP-MS (inductively coupled plasma mass spectrometry) by Huffman Hazen Laboratories. Data was expressed as ppb. Results. Mild to severe damage (Damage Score ≥ 2) was observed on 92% of the components in at least one quadrant, with no severe damage (Damage Score = 4) observed. ICIC damage was observed on three components in three different regions (the posterior lateral, anterior, and medial bearing surface). These observations were confirmed with digital optical microscopy, where we observed as interconnecting pits and indentations with a spiraling or trailing region, consistent with prior observation of ICIC in retrievals (Figure 1). Cobalt was detected in 7 cases, however the metal levels were not as high as levels observed in patients with a failed joint replacement (Table 1). There was no correlation between the metal ion concentration and the damage score on the CoCr femoral condyle. Discussion. This study documents the damage mechanics and associated metallic release into the synovial fluid of “well-functioning” TKA components retrieved at autopsy. It has been suggested that ICIC damage is actually damage from electrocautery during surgery. However, we observed ICIC damage on autopsy retrievals in which the use of electrocautery is unlikely. The damage mechanisms observed on the autopsy TKA components were similar but less severe compared to mechanisms observed in long-term TKA components from revision surgery [1]. More research is needed to better understand the metal release from CoCr femoral components and periprosthetic tissue reactions in TKA


Orthopaedic Proceedings
Vol. 94-B, Issue SUPP_XLIV | Pages 38 - 38
1 Oct 2012
Weidert S Wang L Thaller P Landes J Brand A Navab N Euler E
Full Access

The verification of the alignment of the lower limb is critical for reconstructive surgery as well as trauma surgery in order to prevent osteoarthritis. The mechanical axis is a straight line defined by the center of the femoral head and the center of the ankle joint, ideally passing the knee joint in its center. Whereas the usual preoperative method to determine the mechanical axis of the lower limbs is still the long standing radiograph, common intra-operative methods are the use of an electrocautery cord or an X-ray grid consisting of wire lines underneath the patient. Both methods require the surgeon to bring the femoral head and the ankle joint exactly to overlay with a radiopaque line that passes through both points. The distance of the knee center from this line is defined as the mechanical axis deviation (MAD). In order to reduce the errors introduced by perspective projection effects, the joint centers must be placed in the center of the c-arm images, which definitely requires time, experience and additional radiation. We propose a computer aided X-ray stitching method that puts individual X-ray images into a panoramic image frame combining the Camera Augmented Mobile C-arm (CamC) system, which features a video camera with its optical center virtually coinciding with the origin of the X-rays, with an optical tracking marker pattern underneath the operating table. The camera image of the marker pattern is used to perform pose estimation of the C-arm, allowing the calculation of the x-ray source motion between the positions in which the individual X-rays were taken. By estimating the homography, the different X-rays can be registered into a panoramic frame, enabling perfect alignment and metric measurements. In order to reduce parallax effects that lead to axis and metric measurement errors, we applied a method requiring two constraints: The bone plane has to be roughly parallel to the planar marker pattern and the distance between the marker plane and the bone plane has to be estimated. In order to evaluate the method, we used a life-size synthetic skeleton leg. After tightening a straight wire between the centers of the hip and ankle joint, the knee joint was bent into a MAD of 55 mm, which was confirmed by measuring the distance between the knee center and the wire with a ruler. The leg phantom was then placed on a radiolucent operating table, parallel to the pattern plane 130 mm underneath. The operating table was moved through the C-arm while acquiring the three desired X-ray images. which were registered into a panoramic image frame. The centers of the femoral head, the ankle, and the knee were manually determined on the generated panoramic image by a surgeon. The mechanical axis was automatically displayed and the MAD was visualised in the image and computed as 55.23 mm. We presented a new solution to intra-operatively verify alignment of the lower extremity. When using the CamC system, only a marker pattern has to be used for tracking. No additional tracking devices and calibration procedures are needed. Furthermore, the presented method only requires three x-rays that cover the femoral head, the knee and the ankle and marking of the three spots. Due to the parallax correction, these spots do not have to be exactly in the center of the picture. For this reason, compared to using an X-ray grid or an electrocautery cord, our method allows the procedure to be much faster and reduces the number of x-ray images. However, for clinical evaluation, a patient study will be conducted in the future


Orthopaedic Proceedings
Vol. 100-B, Issue SUPP_10 | Pages 122 - 122
1 Jun 2018
Gonzalez Della Valle A
Full Access

Adequate soft tissue balance at the time of total knee arthroplasty (TKA) prevents early failure. In cases of varus deformity, once the medial osteophytes have been resected, a progressive release of the medial soft tissue sleeve (MSS) from the proximal medial tibia is needed to achieve balance. The “classic” medial soft tissue release technique, popularised by John Insall et al., consists of a sharp subperiosteal dissection from the proximal medial tibia that includes superficial and deep medial collateral ligament (MCL), semimembranosus tendon, posteromedial capsule, along with the pes anserinus tendons, if needed. However, this technique allows for little control over releases that selectively affect the flexion and extension gaps. When severe deformity is present, an extensive MSS release can cause iatrogenic medial instability and the need to use a constrained implant. It has been suggested that the MSS can be elongated by performing selective releases. This algorithmic approach includes the resection of the posterior osteophytes as the initial balancing gesture. If additional MSS release is necessary in extension, a subperiosteal release of the posterior aspect of the MSS is performed with electrocautery, detaching the posterior aspect of the deep MCL, posteromedial capsule and semimembranosus tendon for the proximal and medial tibia. Dissection is rarely extended more than 1.5 cm distal to the joint line. If additional release is necessary in extension, the medial compartment is tensioned with a laminar spreader and multiple needle punctures (generally less than 8) are performed in the taut portion of the MSS using an 18G or 16G needle. If additional release is necessary to balance the flexion gap, multiple needle punctures in the anterior aspect of the MSS are performed. This stepwise approach to releasing the MSS in a patient with a varus deformity allows the surgeon to target areas that selectively affect the flexion and extension gaps. Its use has resulted in diminished use of constrained TKA constructs and subsequent cost savings. We have not seen an increase in post-operative instability developing within the first post-operative year. We recommend caution when implementing this technique. Unlike the traditional release method, pie-crusting is likely technique-dependent and failure can occur within the MCL itself. Due to the critical importance of the MCL in knee stability, further research and continuous follow up of patients undergoing TKA with this technique are warranted. Intra-operative sensing technology may be useful to quantitate the effect of pie-crusting on the compartmental loads and overall knee balance


Orthopaedic Proceedings
Vol. 99-B, Issue SUPP_7 | Pages 79 - 79
1 Apr 2017
Haas S
Full Access

Deformity correction is a fundamental goal in total knee arthroplasty. Severe valgus deformities often present the surgeon with a complex challenge. These deformities are associated with abnormal bone anatomy, ligament laxity and soft tissue contractures. Distorted bone anatomy is due to bone loss on the lateral femoral condyle, especially posteriorly. To a lesser extent bone loss occurs from the lateral tibia plateau. The AP axis (Whiteside's Line) or epicondylar axis must be used as a rotational landmark in the severely valgus knee. Gap balancing techniques can be helpful in the severely valgus knee, but good extension balance must be obtained before setting femoral rotation with this technique. Coronal alignment is generally corrected to neutral or 2- to 3-degree overcorrection to mild mechanical varus to unload the attenuated medial ligaments. The goal of soft tissue releases is to obtain rectangular flexion and extension gaps. Soft tissue releases involve the IT band, posterolateral corner/arcuate complex, posterior capsule, LCL, and popliteus tendon. Assessment of which structures is made and then releases are performed. In general, pie crust release of the IT band is sufficient for mild deformity. More severe deformities require release of the posterolateral corner / arcuate and posterior capsule. I prefer a pie crust technique, while Ranawat has described the use of electrocautery to perform these posterior/ posterolateral releases. In most cases the LCL is not released, however, this can be released from the lateral epicondyle, if necessary. Good ligament balance can be obtained in most cases, however, some cases with severe medial ligament attenuation require additional ligament constraint such as a constrained condylar implant


Orthopaedic Proceedings
Vol. 99-B, Issue SUPP_22 | Pages 61 - 61
1 Dec 2017
Davies G Bradford N Oliver R Verheul R Bruce W Walsh W
Full Access

Aim. The prevention of surgical-site infection (SSI) is of great importance. Airborne particulate correlates with microbial load and SSI. There are many potential sources of airborne particulates in theatre and from an experimental point of view impossible to control. We evaluated the effectiveness of a novel air decontamination-recirculation system (ADRS) in reducing airborne particles in a laboratory environment and controlled the introduction of particulate using diathermy. Methods. Airborne particles were measured with and without activation of the ADRS in PC2 laboratory to provide a baseline. Particles were generated in a controlled manner utilising electrocautery ablation of porcine skin tissue. Ablation was performed at 50W power (Cut) for 60 seconds at a constant rate with and without the ADRS operating in the PC2 laboratory. Particles were measured continuously in 30s intervals at two sites 0.5m and 3m from the site of diathermy. Adequate time was allowed for return to baseline between each repetition. Each experiment was repeated 10 times. Results. The ADRS significantly reduced baseline airborne particles in the empty PC2 laboratory. When using electrocauterization (as a source of particle generation), peak particles were significantly higher at 0.5m compared to 3m. Small particles (0.3–0.5 microns) were reduced at 0.5m with ADRS whilst larger particles were not. The ADRS significantly reduced all particles of 0.3–10.0 microns at 3m. Particles also returned to a lower baseline and at a faster rate with the ADRS. Conclusion. Airborne particle counts are a surrogate measure of microbial load. As likelihood of SSI is assumed to increase with the quantity of airborne pathogens present, there is a great deal of interest in methods of reducing airborne particle count in the operating theatre. Distance from the source of particle generation influences particle load and has potential clinical relevance for the operating theatre layout and staff. The ADRS effectively reduced the peaks and baseline of airborne particles and hastened the clearance of generated particles. The use of this technology in the operating theatre is of great interest for further research as suppression of airborne particulate may play a role in reducing SSIs. Diathermy provides a simple means to introduce particles in a controlled manner for such experiments


Orthopaedic Proceedings
Vol. 98-B, Issue SUPP_22 | Pages 77 - 77
1 Dec 2016
Haas S
Full Access

Deformity correction is a fundamental goal in total knee arthroplasty. Severe valgus deformities often present the surgeon with a complex challenge. These deformities are associated with abnormal bone anatomy, ligament laxity and soft tissue contractures. Distorted bone anatomy is due to bone loss on the lateral femoral condyle, especially posteriorly. To a lesser extent bone loss occurs from the lateral tibia plateau. The AP Axis (Whiteside's Line) or Epicondylar axis must be used as a rotational landmark in the severely valgus knee. Gap balancing techniques can be helpful in the severely valgus knee, but good extension balance must be obtained before setting femoral rotation with this technique. Coronal alignment is generally corrected to neutral or 2- to 3-degree overcorrection to mild mechanical varus to unload the attenuated medial ligaments. The goal of soft tissue releases is to obtain rectangular flexion and extension gaps. Soft tissue releases involve the IT band, Posterolateral Corner/Arcuate Complex, Posterior Capsule, LCL, and Popliteus Tendon. Assessment of which structures is made and then releases are performed. In general Pie Crust release of the ITB is sufficient for mild deformity. More severe deformities require release of the Posterolateral Corner/Arcuate Complex and Posterior Capsule. I prefer a pie crust technique, while Ranawat has described the use of electrocautery to perform these posterior/ posterolateral releases. In most cases the LCL is not released, however, this can be released from the lateral epicondyle, if necessary. Good ligament balance can be obtained in most cases, however, some cases with severe medial ligament attenuation require additional ligament constraint such as a constrained condylar implant


Orthopaedic Proceedings
Vol. 98-B, Issue SUPP_17 | Pages 21 - 21
1 Nov 2016
Sperling J
Full Access

The standard approach is through the deltopectoral interval. Among patients with prior incisions, one makes every effort to either utilise the old incision or to incorporate it into a longer incision that will allow one to approach the deltopectoral interval and retract the deltoid laterally. The deltopectoral interval is most easily developed just distal to the clavicle, where there is a natural infraclavicular triangle of fat that separates the deltoid and pectoralis major muscles even in very scarred or stiff shoulders. Typically, the deltoid is retracted laterally leaving the cephalic vein on the medial aspect of the exposure. The anterior border of the deltoid is mobilised from the clavicle to its insertion on the humerus. The anterior portion of the deltoid insertion together with the more distal periosteum of the humerus may be elevated slightly. The next step is to identify the plane between the conjoined tendon group and the subscapularis muscle. Dissection in this area must be done very carefully due to the close proximity of the neurovascular group, the axillary nerve, and the musculocutaneous nerve. Scar is then released from around the base of the coracoid. The subacromial space is freed of scar and the shoulder is examined for range of motion. Particularly among patients with prior rotator cuff surgery, there may be severe scarring in the subacromial space. Internal rotation of the arm with dissection between the remaining rotator cuff and deltoid is critical to develop this plane. If external rotation is less than 30 degrees, one can consider incising the subscapularis off bone rather than through its tendinous substance. For every 1 cm that the subscapularis is advanced medially, one gains approximately 20 to 30 degrees of external rotation. The rotator interval between the subscapularis and supraspinatus is then incised. This release is then continued inferiorly to incise the inferior shoulder capsule from the neck of the humerus. This is performed by proceeding from anterior to posterior with progressive external rotation of the humerus staying directly on the bone with electrocautery and great care to protect the axillary nerve. The key for glenoid exposure as well as improvement in motion is deltoid mobilization, a large inferior capsular release, aggressive humeral head cut and osteophyte removal


Orthopaedic Proceedings
Vol. 95-B, Issue SUPP_22 | Pages 87 - 87
1 May 2013
Haas S
Full Access

Deformity correction is a fundamental goal in Total Knee Arthroplasty. Severe valgus deformities often present the surgeon with a complex challenge. These deformities are associated with abnormal bone anatomy, ligament laxity and soft tissue contractures. Distorted bone anatomy is due to bone loss on the lateral femoral condyle, especially posteriorly. To a lesser extent bone loss occurs from the lateral tibia plateau. The AP Axis (Whiteside's Line) or Epicondylar axis must be used as a rotational landmark in the severely valgus knee. Gap balancing techniques can be helpful in the severely valgus knee, but good extension balance must be obtained before setting femoral rotation with this technique. Coronal alignment is generally corrected to neutral or 2 to 3 degree overcorrection to mild mechanical varus to unload the attenuated medial ligaments. The goal of soft tissue releases is to obtain rectangular flexion and extension gaps. Soft tissue releases involve the IT band, Posterolateral corner/Accurate Complex, Posterior Capsule, LCL, and Popliteus Tendon. Assessment of which structures is made and then releases are performed. In general Pie Crust release of the ITB is sufficient for mild deformity. More severe deformities require release of the Posterolateral corner/Accurate Complex and Posterior Capsule. I prefer a pie crust technique, while Ranawat has described the use of electrocautery to perform these posterior/ posterolateral releases. In most cases the LCL is not released, however, this can be released from the lateral epicondyle if necessary. Good ligament balance can be obtained in most cases, however, some cases with severe medial ligament attenuation require additional ligament constraint such as a constrained condylar implant


Orthopaedic Proceedings
Vol. 98-B, Issue SUPP_17 | Pages 54 - 54
1 Nov 2016
Lombardi A
Full Access

When dealing with the patella in total knee arthroplasty (TKA) there are three philosophies. Some advocate resurfacing in all cases, others do not resurface, and a third group selectively resurfaces the patella. The literature does not offer one clear and consistent message on the topic. Treatment of the patella and the ultimate result is multifactorial. Factors include the patient, surgical technique, and implant design. With respect to the patient, inflammatory versus non-inflammatory arthritis, pre-operative presence or absence of anterior knee pain, age, sex, height, weight, and BMI affect results of TKA. Surgical technique steps to enhance the patellofemoral articulation include: 1) Restore the mechanical axis to facilitate patellofemoral tracking. 2) Select the appropriate femoral component size with respect to the AP dimension of the femur. 3) When performing anterior chamfer resection, measure the amount of bone removed in the center of the resection and compare to the prosthesis. Do not overstuff the patellofemoral articulation by taking an inadequate amount of bone. 4) Rotationally align the femur appropriately using a combination of the AP axis, the transepicondylar axis, the posterior condylar axis, and the tibial shaft axis. 5) If faced with whether to medialise or lateralise the femoral component, always lateralise. This will enhance patellofemoral tracking. 6) When resurfacing the patella, only evert the patella after all other bony resections have been performed. Remove peripheral osteophytes and measure the thickness of the patella prior to resection. Make every effort to leave at least 15 mm of bone and never leave less than 13 mm. 7) Resect the patella. The presenter prefers a freehand technique using the insertions of the patellar tendon and quadriceps tendon as a guide, sawing from inferior to superior, then from medial to lateral to ensure a smooth, flat, symmetrical resection. Medialise the patellar component and measure the thickness of reconstruction. 8) When not resurfacing the patella, surgeons generally remove all the peripheral osteophytes, and some perform denervation using electrocautery around the perimeter. 9) Determine appropriate patellofemoral tracking only after the tourniquet is released. 10) Close the knee in flexion so as not to tether the soft tissues about the patella and the extensor. With or without patellar resurfacing, implant design plays in important role in minimizing patellofemoral complications. Newer designs feature a so-called “swept back” femur in which the chamfer resection is deepened, and patellofemoral overstuffing is minimised. Lateralizing the trochlear groove on the anterior flange, orienting it in valgus alignment, and gradually transitioning to midline have improved patellofemoral tracking. Extending the trochlear groove as far as possible into the tibiofemoral articulation has decreased patellofemoral crepitation and patellar clunk in posterior stabilised designs. With respect to the tibial component, providing patellar relief anteriorly in the tibial polyethylene has facilitated range of motion and reduced patellar impingement in deep flexion. On the patella side, the all-polyethylene patella remains the gold standard. While data exist to support all three viewpoints in the treatment of the patella in TKA, it is the presenter's opinion that the overwhelming data support patella resurfacing at the time of primary TKA. It is clear from the literature that the status of the patellofemoral articulation following TKA is multifactorial. Surgical technique and implant design are key to a well-functioning patellofemoral articulation. Pain is the primary reason patients seek to undergo TKA. Since our primary goal is to relieve pain, and there has been a higher incidence of anterior knee pain reported without patellar resurfacing, why not resurface the patella?


Bone & Joint Open
Vol. 1, Issue 4 | Pages 74 - 79
24 Apr 2020
Baldock TE Bolam SM Gao R Zhu MF Rosenfeldt MPJ Young SW Munro JT Monk AP

Aim

The coronavirus disease 2019 (COVID-19) pandemic presents significant challenges to healthcare systems globally. Orthopaedic surgeons are at risk of contracting COVID-19 due to their close contact with patients in both outpatient and theatre environments. The aim of this review was to perform a literature review, including articles of other coronaviruses, to formulate guidelines for orthopaedic healthcare staff.

Methods

A search of Medline, EMBASE, the Cochrane Library, World Health Organization (WHO), and Centers for Disease Control and Prevention (CDC) databases was performed encompassing a variety of terms including ‘coronavirus’, ‘covid-19’, ‘orthopaedic’, ‘personal protective environment’ and ‘PPE’. Online database searches identified 354 articles. Articles were included if they studied any of the other coronaviruses or if the basic science could potentially applied to COVID-19 (i.e. use of an inactivated virus with a similar diameter to COVID-19). Two reviewers independently identified and screened articles based on the titles and abstracts. 274 were subsequently excluded, with 80 full-text articles retrieved and assessed for eligibility. Of these, 66 were excluded as they compared personal protection equipment to no personal protection equipment or referred to prevention measures in the context of bacterial infections.


Bone & Joint Open
Vol. 1, Issue 6 | Pages 236 - 244
11 Jun 2020
Verstraete MA Moore RE Roche M Conditt MA

Aims

The use of technology to assess balance and alignment during total knee surgery can provide an overload of numerical data to the surgeon. Meanwhile, this quantification holds the potential to clarify and guide the surgeon through the surgical decision process when selecting the appropriate bone recut or soft tissue adjustment when balancing a total knee. Therefore, this paper evaluates the potential of deploying supervised machine learning (ML) models to select a surgical correction based on patient-specific intra-operative assessments.

Methods

Based on a clinical series of 479 primary total knees and 1,305 associated surgical decisions, various ML models were developed. These models identified the indicated surgical decision based on available, intra-operative alignment, and tibiofemoral load data.