A durable biological fixation between implant and bone depends largely on the micro-motions [Pilliar et al., 1986]. Finite element analysis (FEA) is a numerical tool to calculate micro-motions during physiological loading. However, micromotions can be simulated and calculated in various ways. Generally, only a single peak force of an activity is applied, but it is also possible to apply discretized loads occurring during a continuous activity, offering the opportunity to analyze incremental micro-motions as well. Moreover, micro-motions are affected by the initial press-fit. We therefore aimed to evaluate the effect of different loading conditions and calculation methods on the micro-motions of an uncemented femoral knee component, while varying the interference-fit.

We created an FE model of a distal femur based on calibrated CT-scans. A Sigma® Cruciate-Retaining Porocoat® (DePuy Synthes, Leeds, UK) was placed following the surgical instructions. A range of interference-fits (0–100 µm) was applied, while other contact parameters were kept unchanged. Micro-motions were calculated by tracking the projection of implant nodes onto the bone surface. We defined three different micro-motions measures: micro-motions between consecutive increments of a full loading cycle (incremental), micro-motions for each increment relative to the initial position (reference), and the largest distance between projected displacements, occurring during a discretized full cycle (resulting) (Fig. 1A). Four consecutive cycles of normal gait and squat movements were applied, in different configurations. In the first configuration, incremental tibiofemoral and patellofemoral contact forces were applied, which were derived from Orthoload database using inverse dynamics [Fitzpatrick et al., 2012]. Secondly, we applied the same loads without the patellofemoral force, which is often used in experimental set-ups. Finally, only the peak tibiofemoral force was applied, as a single loading instance. We calculated the average of micro-motions of all nodes per increment to compare different calculation techniques. The percentage of area with resulting micro-motions less than 5 µm was also calculated.

The percentage of surface area was increased non-linearly when the interference fit changed from 0 to 100 µm particularly for squat movement. Tracking nodes over multiple cycles showed implant migration with interference-fits lower than 30µm (Fig. 1A). Loading configurations without the patellofemoral force, and with only the peak tibiofemoral force slightly overestimated and underestimated the resulting micro-motions of squat movement, respectively; although, the effect was less obvious for the gait simulation when no patella force was applied. Both incremental and reference micro-motions underestimated the resulting micro-motions (Fig. 1B). Interestingly, the reference micro-motions followed the pattern of the tibiofemoral contact force (Fig. 1B).

The calculation technique has a substantial effect on the micro-motions, which means there is a room for interpretation of micro-motions analyses. This furthermore stresses the importance of validation of the predicted micro-motions against experimental set-ups. In addition, the minor effect of loading configurations indicates that a simplified loading condition using only the peak tibiofemoral force is suitable for experimental studies. From a clinical perspective, the migration pattern of femoral components implanted with a low interference fit stresses the role of an adequate surgical technique, to obtain a good initial stability.

Femoral knee implants have promising outcomes, although some high-flex designs have shown rather high loosening rates (Han et al., 2007). In uncemented implants, it is vital to limit micromotions at the implant-bone interface, to facilitate secondary fixation through bone ingrowth (kienapfel et al., 1999). Hence, it is essential to investigate how micromotions of different uncemented implants are affected by various loading conditions when a range of bone qualities as a patient-related factor is applied.

Using finite element (FE) analysis, we simulated implant-bone interface micromotions during four consecutive cycles of normal gait and squat movements. An FE model of a distal femur was generated based on calibrated CT-scans, after which Sigma® and LCS® Cruciate-Retaining Porocoat® components (DePuy Synthes, Leeds, UK) were implanted. Using a frictional contact algorithm (µ=0.95), an initial press-fit fixation was simulated, which was previously validated against experimental data. The micromotions were calculated by tracking the projection of implant nodes on the bone surface excluding overhang area. The applied loading patterns were based on discretized simulations, providing incremental loads for each activity based on implant-specific kinematics, which was derived from Orthoload database using inverse dynamics (Fitzpatrick et al., 2012). This provided the opportunity to calculate incremental micromotions, but also the resulting micromotions for each single cycle, for both activities. In addition, the percentage of implant surface area with resulting micromotions less than a defined threshold was calculated.

Regardless of the type of loading, in all simulations, the predicted micromotions were highest in the first cycle, suggesting settling of the implant during initial cycle. The Sigma®implant displayed a 30% larger area with micromotions below the threshold of 5 microns, for both loading conditions (Fig. 1A). The highest micromotions occurred at the anterior flange, regardless of type of activity or design. Squatting had a more detrimental effect on the primary stability, with smaller areas of low micromotions as compared to the gait load (Fig. 1B). Bone stiffness had a minor effect, which was more apparent for squatting (Fig. 1B).

We found acceptable low ranges of micromotions in both implant designs, although demanding activities such as squatting generated higher motions. In addition, LCS® experienced higher micromotions, probably caused by the smaller contact area at bone-implant interface compared with Sigma®. Nevertheless, the predicted micromotions were all below the clinically relevant threshold for bone ingrowth (<40 microns) (kienapfel et al., 1999). Furthermore, our simulated settling behavior stresses the necessity for simulating multiple loading cycles, rather than just a single cycle. The effect of bone stiffness was evident, but only to a limited extent. The main current limitation of our study is the utilization of an elastic material model for the bone which is probably the reason to predict a low range of micromotions. We are planning to make the material model more realistic, by including plasticity and viscoelastic bone behavior.

Local infiltration analgesia (LIA) is promoted as an effective treatment modality for pain control after total knee arthroplasty (TKA) (1). A mixture of drugs is used to provide a multimodal analgesic effect. Previous studies reported that the use of these drugs is safe. After we carefully implemented a LIA study protocol in our practice, concerns raised about patient safety with probably higher infection rates. This forced us to perform an interim analysis after the first 58 cases.

58 patients underwent a unilateral TKA with a standardised LIA protocol (2), which consisted of a mixture of ropivacaine, epinephrine, and triamcinolone acetonide. Complications, knee function and patient satisfaction scores were prospectively recorded during regular outpatient control.

Four patients (6.9%) presented with signs of periprosthetic joint infection (PJI) within two months after surgery. Baseline characteristics were similar between the infected and non infected group. All infections were treated with debridement and retention, and antimicrobial treatment was started. One patient who suffered an infection died during followup. At two years followup all implants could be retained. Knee function and KSS score were acceptable for the patients who suffered PJI.

There is no consensus on the combination of drugs used for LIA. The application of corticosteroids in LIA is reported to be safe (3), but arguable results about the injection of local corticosteroids around knee arthroplasty surgery in the past have raised suspicion in literature (4). Combined with our unacceptable high rate of PJI, we believe that the current body of evidence, with small heterogeneous series, does not support the safe use of corticosteroids in LIA.

Pegs are often used in cementless total knee replacement (TKR) to improve fixation strength. Studies have demonstrated that interference fit, surface properties, bone mineral density (BMD) and viscoelasticity affect the performance of press-fit designs. These parameters also affect the insertion force and the bone damage occurring during insertion. We aimed to quantify the effect of the aforementioned parameters on the short-term fixation strength of cementless pegs.

6 mm holes were drilled in twenty-four human femora. BMD was measured using calibrated CT-scans, and randomly assigned to samples. Pegs were produced to investigate the effect of interference fit (diameters 6.5 and 7.6 mm), surface treatment (smooth and rough- porous-coating [friction coefficient: 1.4]) and bone relaxation (relaxation time 0 and 30 min) and interactions were studied using a DOE method. Two additional rough surfaced peg designs (diameters 6.2 and 7.3 mm) were included to scrutinize interference. Further, a peg based on the LCS Porocoat® (DePuy Synthes Joint Reconstruction, Leeds, UK) was added as a clinical baseline. In total seven designs were used (n = 10 for all groups). Pegs were inserted and extracted using an MTS machine (Figure 1), while recording force and displacement. Bone damage was defined as the difference between the cross-sectional hole area prior to and after the test.

BMD and interference fit were significant factors for insertion force. BMD had a significant positive correlation with pull-out force and subsequent analyses were therefore normalised for BMD.

Pull-out force increased significantly with interference for both surface coatings at time 0 (p < 0.05). However, after 30 minutes the effect remained significant for rough pegs only (p < 0.05-Figure 2A).

Additionally, the pull-out force increased with diameter in a non-linear manner for the rough pegs (Figure 2B). The two surface treatments were not significantly different to the clinical comparator. Interference fit was the only significant factor for bone damage.

BMD was significant for insertion and pull-out forces, reinforcing the need to account for this factor in biomechanical studies and clinical practice. This study also highlights the importance of time in studying bone interactions, with surface treatment and interference showing different interaction effects with relaxation time. Although smooth pegs initially have a higher pull-out force, this effect reduces over time whereas the pullout force for rough pegs is maintained. Smooth pegs also show time sensitivity in relation to interference and the benefit of increased interference reduces over time, whereas it is maintained in rough pegs. This may be explained by different damage (compressive and abrasive) mechanisms associated with different surface treatments.

In conclusion, BMD and interference fit are significant factors for initial fixation. Bone relaxation plays an important role as it reduces the initial differences between groups. Therefore, these findings should be strongly considered in the design development of cementless TKR.

The effect of an advanced porous surface morphology on the mechanical performance of an uncemented femoral knee prosthesis was investigated. Eighteen implants were inserted and then pushed-off from nine paired femurs (Left legs: advanced surface coating; right legs: Porocoat® surface coating as baseline). Bone mineral density (BMD) and anteroposterior dimension were measured, which both were not significantly different between groups. The insertion force was not significantly different, but push-off force was significantly higher in the advanced surface coating group (P = 0.007). BMD had direct relationship with the insertion force and push-off force (p < 0.001). The effect of surface morphology on implant alignment was very small. We suggest that the surface properties create a higher frictional resistance thereby providing a better inherent stability of implants featuring the advanced surface coating.

To achieve desirable outcomes in cementless total knee replacement (TKR), sufficient primary stability is essential. The primary stability inhibits excessive motions at the bone-implant interface, hence providing the necessary condition for osseointegration [1]. Primary stability for cementless TKR is provided by press-fit forces between the bone and implant. The press-fit forces depend on several factors including interference fit, friction between bone and implant surface, and the bone material properties. It is expected that bone mineral density (BMD) will affect the stability of cementless TKR [2]. However, the effect of BMD on the primary stability of cementless femoral knee component has not been investigated in vitro.

Phantom calibrated CT-scans of 9 distal femora were obtained after the surgical cuts were made by an experienced surgeon. Since the press-fit forces of the femoral component mainly occur in the Anteroposterior (AP) direction, the BMD was measured in the anterior and posterior faces for a depth of 5 mm; this depth was based on stress distributions from a Finite Element Analysis of the same implant design. In addition, four strain gauges were connected to different locations on the implant's outer surface and implant strain measured throughout as an indication of underlying bone strain. A cementless Sigma CR femoral component (DePuy Synthes Joint Reconstruction, Leeds, UK) was then implanted using an MTS machine. In order to simulate a ‘normal’ bone condition, the implanted bone was preconditioned for one hour at a cyclic load of 250–1500 N, and a rate of 1 Hz. Finally, the implants were pushed-off from the bone in a high-flex position. Forces and displacements were recorded both during insertion and push-off tests.

Strong correlations were found for insertion and push-off forces with BMD, R² = 0.88 and R² = 0.88, respectively (p < 0.001), so although implantation may be harder in patients with higher BMD, initial stability is also improved. A correlation was also found between final strain and push-off forces (R² = 0.89, p < 0.01) and BMD also showed a strong reverse correlation with total bone relaxation (R² = 0.76, p = 0.023). These results indicate that higher BMD induces higher bone strain, which can lead to improved fixation strength.

There is no consensus on the best fixation method for the TKR but some surgeons prefer a cementless design for young and active patients. The results of our study showed that the primary stability of a cementless femoral knee component is directly correlated with the bone mineral density. Therefore, patient selection based on bone quality may increase the likelihood of good osseointegration and adequate long-term fixation for cementless femoral knee components.

Introduction

A few follow-up studies of high flexion total knee arthoplasties report disturbingly high incidences of femoral loosening. Finite element analysis showed a high risk for early loosening at the cement-implant interface at the anterior flange. However, femoral implant fixation is depending on two interfaces: cement-implant interface and the cement-bone interface. Due to the geometry of the distal femur, a part of the cement-bone interface consists of cement-cortical bone interface. The strength of the cement-bone interface is lower than the strength of the cement-implant interface.

The research questions addressed in this study were: 1) which interface is more prone to loosening and 2) what is the effect of different surgical preparation techniques on the risk for early loosening.

High-flexion knee replacements have been developed to accommodate a large range of motion (ROM > 120°) after total knee arthroplasty (TKA). Femoral rollback or posterior translation of the femoral condyles during knee flexion is essential to maximise ROM and to avoid bone-implant impingement during deep knee flexion. The posterior cruciate ligament (PCL) has been described as the main contributor to femoral rollback. In posterior-stabilised TKA designs the PCL is substituted by a post-cam mechanism. The main objective of this study was to analyse the mechanical interaction between the PCL and a highflexion cruciate-retaining knee replacement during deep knee flexion. For this purpose, the mechanical performance of the high-flexion cruciate-retaining TKA design was evaluated and compared with two control designs including a highflexion posterior-stabilised design.

Materials & Methods: Prosthetic knee kinematics and kinetics were computed using a three-dimensional dynamic finite element (FE) model of the knee joint. The FE knee model consisted of a distal femur, a proximal tibia and fibula, a quadriceps and patella tendon, a non-resurfaced patella, TKA components and a posterior cruciate ligament in case cruciate-retaining designs were evaluated. Tibio-femoral and patello-femoral contact were defined in the FE knee model and the polyethylene insert was modelled as a non-linear elastic-plastic material. Three different rotating platform TKA systems were analysed in this study: the high-flexion cruciate-retaining PFC Sigma CR150, the high-flexion posterior-stabilised PFC Sigma RP-F and the conventional cruciate-retaining PFC Sigma RP (Depuy, J& J, UK). Both the polyethylene stress characteristics and the tibio-femoral contact locations were evaluated during a squatting movement (ROM = 50° – 150°).

Results: During deep knee flexion (ROM > 120°), the high-flexion cruciate-retaining TKA design showed a lower peak contact stress (74.7 MPa) than the conventional cruciate-retaining design (96.5 MPa). The posterior-stabilized high-flexion TKA design demonstrated the lowest peak contact stress at the condylar contact interface (54.2 MPa), although the post was loaded higher (77.4 MPa). All three TKA designs produced femoral rollback in the normal flexion range (ROM ≤ 120°), whereas the cruciate-retaining designs showed a paradoxical anterior movement of the femoral condyles during high-flexion.

Discussion: PCL retention is a challenging surgical aim and affects the prosthetic knee load and kinematics as shown in this study. In addition, for adequate functioning the PCL should not be too tight or too lax after surgery. Hence, we investigated the effect of PCL laxity on the prosthetic performance and the best-balanced PCL was used in our simulations. Although PCL balancing is not an issue for posterior-stabilized TKA, we found the tibial post to be loaded relatively high for this implant type.

Recently, high-flexion knee implants have been developed to provide for a large range of motion after total knee arthroplasty. Since knee forces increase with larger flexion angles, it is commonly assumed that high-flex-ion implants are subjected to large loads in the highflexion range (flexion > 120°). However, high-flexion studies often do not consider thigh-calf contact which occurs during high-flexion activities such as squatting and kneeling. We hypothesized that thigh-calf contact is substantial and has a reducing effect on the prosthetic knee loading during deep knee flexion.

The effect of thigh-calf contact on the loading of a knee implant was evaluated using a three-dimensional dynamic finite element knee model. The knee model consisted of a distal femur, a proximal tibia and fibula, a patella, high-flexion components of the PFC Sigma RP-F (Depuy, Warsaw, USA) and a quadriceps and patella tendon. Using this knee model, a squatting movement was simulated including thigh-calf contact characteristics of a typical subject which have been described in an earlier study.

Thigh-calf contact considerably reduced the implant loading during deep knee flexion. At maximal flexion (155°), the compressive knee force decreased from 4.9 to 2.9 times bodyweight. The maximal joint forces shifted from occurring at maximal flexion angle to the flexion angle at which thigh-calf contact initiated (±130°). The maximal polyethylene contact stress at the tibial post decreased from 49.3 to 28.1 MPa at maximal flexion.

This study confirms that thigh-calf contact reduces the knee loading during high-flexion. Both the joint forces and the polyethylene stresses reduced considerably when thigh-calf contact was included.

Background: The selection of presentations at orthopedic meetings is an important process. If the peer reviewers do not consistently agree on the quality score, the review process is arbitrary and open to bias. The aim of this study was:

1) To describe the inter reviewer agreement of a previously designed scoring scheme to rate abstracts submitted for presentation at the Dutch Orthopedic Association.

Methods: We calculated intraclass correlation coefficients (ICC) to measure the level of agreement among reviewers using the International Society of the Knee (ISK) abstract quality of reporting system. Acceptance rate and quality of the abstracts are described.

Results: Of 419 abstracts 229 (55%) were accepted. Inter-reviewer agreement to rate abstracts was substantial 0.68 (95%CI 0.47, 0.83) to almost perfect 0.95 (95%CI 0.92, 0.97) and did not change over the eligible time period. Less abstracts were accepted after 2004 (p = 0.039). The mean ISK abstract score, maximally 100 points, for accepted abstracts ranged from 60.4 (95%CI 57.7, 63.0) to 63.8 (95% CI 62.0, 65.7). The mean ISK abstract score for rejected abstracts varied from 45.8 (95%CI 40.3, 51.2) to 50.6 (95% CI 46.5, 54.8). Both scores for accepted and rejected abstracts did not change over time. Workload of the reviewers did not influence their level of agreement (p=0.167).

Interpretation: The ISK abstract rating system has an excellent inter observer agreement. Other scientific orthopedic meetings could adopt this ISK rating system for further evaluation in local or international setting.

It is impossible to determine the effect of a single parameter in clinical or in-vitro knee research. There are also parameters which can not or hardly be determined. These disadvantages can be overcome with a model. The objective of this study was to create a dynamic FE model of a human knee joint after TKA which is applicable to a variety of research question.

The knee model consisted of a femur, tibia and patella, collateral ligaments and a PCL, combined with a CKS cruciate retaining total knee prosthesis. The patella was not resurfaced. An axialload of 150 N and a quadriceps-force of 81N was applied. The model was validated by the model prediction of joint laxities at different flexion-angles and the calculation of the knee kinematics during flexion-extension.

The predicted varus-valgus laxity at different flexion angles was in between 0 and 6.3 degrees. Laxity values decreased towards extension and towards 90 degrees of flexion. The AP test at 20, 30 and 90 degrees of flexion showed a anterior laxity of 3.1, 4.3 and 2 mm, respectively. The posterior laxity was 5.7 mm, but could only be determined at 90 degrees. The model predicted reasonable kinematics, which were identical for two consecutive flexion-extension movements.

The model predictions were well in agreement with reported values, which were measured experimentally. Differences could be well explained by ligament structures which were (still) omitted with in the model. This dynamic model, in which ligaments were actually modelled as bands, combined all major structures within the knee joint. It was well able to predict laxities and kinematics and turned out to be very stable, mathematically. With this model we will be able to address effects of prosthetic and surgical parameters on the stability and kinematics of the knee joint.

Introduction: The Kudo total elbow prosthesis (TEP) is a well established implant, with good mid-term results. In the last decades this implant underwent several modifications. The last modification (type 5) has overcome the problems of stem breakage of the humeral component by modifications of the stem. The ulnar component can be placed with or without cement; the humeral component is always placed without cement.

Aims of this study: To examine the mid-term results of the Kudo type 5 TEP and to compare the results of the uncemented Kudo total elbow prosthesis (TEP), with the hybrid Kudo TEP (uncemented humeral component and cemented ulnar component).

Material and methods: Between 1994 and 2004 89 Kudo type 5 TEPs were placed for joint destruction due to rheumatoid arthritis (RA). The mean age of the patients was 55 years (range 21–84 years). Twenty-two prostheses were placed in males, 66 in females. Forty-nine TEPs (group 1) were fully uncemented and 40 TEPs (group 2) were hybrid (humeral component uncemented, ulnar component cemented). The groups were comparable as related to age, sex and indication for surgery. After implantation of the prosthesis a radiograph was made every two years or sooner when indicated.

Evaluation took place after an average of 5.3 years of follow up (range 1.7–10.6 years) and consisted of a questionnaire, elbow function assessment and anteroposterior and lateral radiographs in a standard way. Pre- and postoperative range of motion was analysed with the paired T-test. Pain scores and EFAS scores postoperatively were analysed using the independent sample T-test. The survival of the prosthesis was calculated from the time of implant to the time of revision or occurrence of radiolucencies.

Results: In group 1, seven ulnar components had to be revised due to aseptic loosening after a mean follow-up of 4 years (range 1.5–6.3 years). Three of these ulnar components were short-stemmed, four were long stemmed uncemented.

In group 2 five patients died of an unrelated course and no revisions have taken place, one TEP is loose on X-ray (after two years) with a suspicion of septic loosening The EFAS scores (87 in group 1 and 91 in group 2) and range of motion (84 degrees in group 1 and 90 degrees in group 2) were the same in both groups.

Conclusion: In this group of patients with RA the survival of the Kudo type 5 TEP with cemented ulnar component is better as compared to the uncemented ulnar component.

Introduction: Total ankle prostheses (TAP’s) are implanted for end stage cartilage damage especially in patients with rheumatoid arthritis (RA), juvenile idiopathic arthritis (JIA) or post-traumatic arthritis. Little is known about the long term survival of these prostheses in patients with RA and JIA. In this study we examined the outcome of TAP in these patients.

Patients and methods: Between 1994 and 2004 85 TAP’s were implanted in 58 cases (10 males and 48 females) with RA (n=53) or juvenile chronic arthritis (n=5). The records of all patients were reviewed. Every patient was invited for a visit to our outpatient clinic for a history taking, a physical examination and a Kofoed ankle score (a clinical score for ankle function ranging from 0 to 100) was obtained.

Results: The record of every patient was available for review. Two patients had died (cause of death was unrelated to the surgery), and 56 patients could be reexamined. A perioperative fracture (8 medial 3 lateral and 2 tibial) occurred in 13 cases. The fractures were fixed in the same operation and healed without complications; none of these prostheses needed a reintervention. After a mean follow up of 2.7 years (range 1 to 9 years) two patients died with the prosthesis in situ, one patient underwent an above knee amputation for infected arthroplasties of ankle and knee and four prostheses were removed because of loosening or malfunctioning of the prosthesis and arthrodeses were performed. The other 51 cases were analysed and showed a mean Kofoed ankle score of 72.8 (SD=15.8). This score is similar to scores obtained from patients receiving ankle arthroplasties for non-rheumatic indications.

Conclusions: Placement of total ankle prostheses in patients with RA shows good medium term results. The intra-operative fracture rate is high, but does not affect the outcome; none of the failed arthroplasties was due to a preoperative fracture.

Clinical experience of impaction bone grafting for revision knee arthroplasty is limited, with initial stability of the tibial tray emerging as a major concern. The length of the stem and its diameter have been altered to improve stability. Our aim was to investigate the effect of the type of stem, support of the rim and graft impaction on early stability of the tray.

We developed a system for impaction grafting of trays which we used with morsellised bone in artificial tibiae. Trays with short, long thick or long thin stems were implanted, with or without support of the rim. They were cyclically loaded while measuring relative movement.

Long-stemmed trays migrated 4.5 times less than short-stemmed trays, regardless of diameter. Those with support migrated 2.8 times less than those without. The migration of short-stemmed trays correlated inversely with the density of the impacted groups. That of impaction-grafted tibial trays was in the range reported for uncemented primary trays. Movements of short-stemmed trays without cortical support were largest and sensitive to the degree of compaction of the graft. If support of the rim was sufficient or a long stem was used, impacted morsellised bone graft achieved adequate initial stability.

Malfunctioning of Total Knee Replacements is often related to patella-femoral problems. As the patella groove guides the patella during flexion, the difference between anatomic- and prosthetic groove geometry may be of major influence concerning patella-femoral problems. This study focusses on the orientation or direction of the femoral patella groove, relative to the mechanical axis of the femur. Literature shows a controversy in measured groove orientation: Eckhoff et al. (1996) have measured a lateral groove, and Feinstein et al. (1996) have measured a medial groove, relative to the mechanical axis. Current femoral knee components have a lateral, or neutral directed patella groove. As most TKA surgical techniques subscribe an exorotation of the femoral component during implantation, the prosthetic in vivo situation will show a lateral groove. The objectives were to clarify the described controversy and to determine whether there is a difference in anatomic- and prosthetic groove orientation, which might cause patella-femoral problems.

The patella groove orientation of 100 human femora was measured using a 3-D measurement system. A spherical measurement probe was moved through the groove, starting at the notch and finishing at the cartilage edge, to simulate patella motion. The patella groove angle was defined as the angle between the mechanical axis and the measured groove points, in the frontal plane. A medial patella groove angle of 1.8±2.6° was measured. An implanted situation of a femoral component with neutral groove showed a lateral groove angle of 1.3°. An implanted situation of a femoral component with assymmetrical groove showed a lateral groove angle of 2.6°. The authors measured a medial oriented patella groove. This anatomical groove orientation is in contradiction with current femoral knee component design and surgical practice, because that results in a lateral oriented groove. This difference in anatomic- and prosthetic groove orientation may be a cause of patella-femoral problems.

Aims: The purpose of this study is to validate a novel, quantitative functional test for TKA patients using commonly used subjective questionnaires as standard. Methods: Electrogoniometry was used to get information about the stability of rising from a chair. Thirteen pre Ðoperative TKA patients were measured while rising from a chair at two different heights. Using phaseplots (relationship between joint angle and joint velocity), the relative phase between the hip and knee was calculated. Instability was deþned as the standard deviation over ten trials for every patient and each height. An independent physician administered the WOMAC, KSS and SF-36 questionnaires. The instability factor of rising was correlated (using Spearmanñs Rho) to the outcomes of the questionnaires. Results: The stability of rising correlated moderately high with the questionnaires. Best correlations were calculated for instability and the WOMAC and SF-36 physical functioning (0.45 and 0.56, respectively). The worst correlation was with the KSS pain score (0.05). In general, the correlations for the lowest chair height were slightly higher. Conclusions: As there is no gold standard for functional evaluation of the TKA, a chair rise protocol has been developed. In this study the stability of rising correlates moderately high with the WOMAC, KSS and SF-36 questionnaires. The stability of rising from a lower chair seems to discriminate better than rising from a higher chair. This test will be used as a quantitative functional follow up of TKA patients.