The leading indication for revision total hip
arthroplasty (THA) remains aseptic loosening owing to wear. The younger,
more active patients currently undergoing THA present unprecedented
demands on the bearings. Ceramic-on-ceramic (CoC) bearings have
consistently shown the lowest rates of wear. The recent advances,
especially involving alumina/zirconia composite ceramic, have led
to substantial improvements and good results Alumina/zirconia composite ceramics are extremely hard, scratch
resistant and biocompatible. They offer a low co-efficient of friction
and superior lubrication and lower rates of wear compared with other
bearings. The major disadvantage is the risk of fracture of the
ceramic. The new composite ceramic has reduced the risk of fracture
of the femoral head to 0.002%. The risk of fracture of the liner
is slightly higher (0.02%). Assuming that the components are introduced without impingement,
CoC bearings have major advantages over other bearings. Owing to
the superior hardness, they produce less third body wear and are
less vulnerable to intra-operative damage. The improved tribology means that CoC bearings are an excellent
choice for young, active patients requiring THA. Cite this article:
We have investigated the effect of using tranexamic
acid (TXA) during peri-acetabular osteotomy (PAO) on peri-operative
blood loss and blood transfusion requirements. In addition we analysed
whether the use of TXA was associated with an increased risk of
venous thromboembolism (VTE) following this procedure. A consecutive series of 96 PAOs, performed by a single surgeon,
were reviewed. A total of 48 patients received TXA and 48 did not.
The TXA group received a continuous infusion of TXA at a rate of
10 mg/kg/h. The primary outcome measure was the requirement for
blood transfusion. Secondary outcomes included total blood loss,
the decrease in the level of haemoglobin in the blood, the length
of hospital stay, and the complications of this treatment. The mean rate of transfusion was significantly lower in the TXA
group (62.5% The use of TXA reduced the blood loss and the rate of transfusion
after PAO significantly, without adverse effects such as an increased
rate of VTE. Cite this article:
The accurate reconstruction of hip anatomy and
biomechanics is thought to be important in achieveing good clinical
outcomes following total hip arthroplasty (THA). To this end some
newer hip designs have introduced further modularity into the design
of the femoral component such that neckshaft angle and anteversion,
which can be adjusted intra-operatively. The clinical effect of
this increased modularity is unknown. We have investigated the changes
in these anatomical parameters following conventional THA with a
prosthesis of predetermined neck–shaft angle and assessed the effect
of changes in the hip anatomy on clinical outcomes. In total, 44 patients (mean age 65.3 years (standard deviation
( The mean pre-operative neck–shaft angle was significantly increased
by 2.8° from 128° ( Cite this article:
The leading cause for total hip arthroplasty (THA) revision remains aseptic loosening due to bearing wear. The younger and more active patients currently undergoing arthroplasty present unprecedented demands on THA-bearings. Ceramic-on-ceramic (CoC) bearings have consistently shown the lowest wear rates. The recent advances, especially in alumina CoC bearings, have solved many past problems and produced preferable results in vitro. Alumina ceramics are extremely hard, scratch resistant, biocompatible, offer a low coefficient of friction, superior lubrication and lower wear rates in comparison to other bearings in THA. The major disadvantage of ceramics used to be fracture. The new generation of alumina ceramics, has reduced the risk of ball fracture to 0.03–0.05%. The risk for liner fracture is even lower. Assuming an impingement-free component implantation, CoC bearings have major advantages over other bearing combinations. Due to the superior hardness, CoC bearings produce less third body wear and are virtually impervious to damage from instruments during the implantation process. A complication specific to CoC bearings is squeaking. Squeaking occurs if the friction in the joint articulation is sufficient to excite vibrations to audible magnitudes (due to loss of lubrication). The high range of reported squeaking (0.45% to 10.7%) highlights the importance of correct implant position. If a correct implant position can be guaranteed, then squeaking is rare and without clinical significance. The improved tribology and presumable resulting implant longevity make CoC the bearing of choice for young and active patients. Especially the alumina matrix (Biolox delta) offers increased burst strength and greater fracture toughness.
The endoprosthetic treatment of secondary osteoarthritis resulting from congenital hip dysplasia is difficult due to the small diameter of the acetabulum and the hypoplastic anterolateral bone stock. On the femoral side the increased femoral anteversion, insufficient femoral offset and proximal femoral deformities (mostly valgus deformities) as well as the small diameter and straight form of the intramedullary canal pose challenges. Careful preoperative planning is mandatory. The Crowe classification is usually used to describe these pathologies. In severe cases (Crowe 3 and especially Crowe 4) a shortening and derotating femoral osteotomy should be taken into account. Small acetabular components, acetabular augments, and modular femoral components must be available at all times. For acetabular fixation press-fit cups are preferred today, but excellent results were also described for threaded cups. The advantage of press-fit cups is the extensively documented and superior track record, but threaded cups allow for an easier reconstruction of the original hip center as well as slight medialization. As a result of medialization a reduction in polyethylene wear together with a low rate of loosening lead to very good long-term results in a younger patient population. Cementless straight stems are documented to be preferable for the small femoral diameter and the straight anatomic shape of the proximal femur. Nevertheless, the higher complication rate, especially the increased rate of nerve palsies, should be preoperatively discussed with the patient. The ideal bearing surface is currently unclear, ceramic-on-ceramic seems to be promising, although the longest data available support the use of metal-on-polyethylene.
Intact abductors of the hip play a crucial role
in preventing limping and are known to be damaged through the direct lateral
approach. The extent of trauma to the abductors after revision total
hip replacement (THR) is unknown. The aim of this prospective study
was to compare the pre- and post-operative status of the gluteus
medius muscle after revision THR. We prospectively compared changes
in the muscle and limping in 30 patients who were awaiting aseptic
revision THR and 15 patients undergoing primary THR. The direct
lateral approach as described by Hardinge was used for all patients.
MRI scans of the gluteus medius and functional analyses were recorded
pre-operatively and six months post-operatively. The overall mean
fatty degeneration of the gluteus medius increased from 35.8% (1.1
to 98.8) pre-operatively to 41% (1.5 to 99.8) after multiple revision
THRs (p = 0.03). There was a similar pattern after primary THR,
but with considerably less muscle damage (p = 0.001), indicating
progressive muscle damage. Despite an increased incidence of a positive
Trendelenburg sign following revision surgery (p = 0.03) there was
no relationship between the cumulative fatty degeneration in the
gluteus medius and a positive Trendelenburg sign (p = 0.26). The
changes associated with other surgical approaches to the hip warrant
investigation. Cite this article:
The utilization of sonicate fluid cultures (SFC) has been shown to increase the detection rate of periprosthetic joint infection (PJI) in comparison to the use of conventional microbiological methods, because sonication enables a sampling of the causative bacteria directly from the surface of the endoprosthetic components. The hypothesis of this study is that not only will the detection rate of PJI be improved, but also the detection rate of polymicrobial infection in patients with total knee arthroplasty (TKA) revision surgery. 74 patients which underwent TKA revision surgery received a synovial aspiration, intraoperative tissue cultures, histological sampling of the periprosthetic membrane, and sonication of the explanted endoprosthesis. A PJI was defined according to the following criteria: presence of intraarticular pus or a sinus tract, positive isolation of causative bacteria in ≥2 microbiological samples or a histological membrane indicative of infection (type II or III periprosthetic membrane).Introduction
Material and methods
Acetabular retroversion has been implicated as a risk factor for the development of early hip osteoarthritis. In clinical practice standard osseous signs such as the cross-over sign (COS) and the posterior wall sign (PWS) are widely used to establish the diagnosis of acetabular retroversion on plain radiographs. Despite standardized radiological evaluation protocols, an increased pelvic tilt can lead to a misdiagnosis of acetabular retroversion in AP radiographs and 2D MR or CT scans. Previous studies have shown that the elimination of observer bias using a standardized methodology based on 3D-CT models and the anterior pelvic plane (APP) for the assessment of COS and PWS results in greater diagnostic accuracy. Using this method a prevalence of 28% for COS and 24% for PWS has been found in a cohort of patients with symptoms indicative of FAI, however the prevalence of both signs in asymptomatic adults remains unknown. This study therefore sought to establish the prevalence of the COS and PWS in relation to the APP in an asymptomatic population using a reliable and accurate 3 D-CT based assessment. A large pool of consecutive CT scans of the pelvis undertaken in our department for conditions unrelated to disorders of the hip was available for analysis. Scans in subjects with a Harris hip score of less than 90 points were excluded leaving a sample of 100 asymptomatic subjects (200 hips) for this study. A previously established 3D analysis method designed to eliminate errors resulting from variations in the position and orientation of the pelvis during CT imaging was applied to determine in order to assess the prevalence of the COS and PWS in relation to the APP. Here, the acetabuli were defined as retroverted if either the COS, PWS or both were positive.INTRODUCTION:
METHODS:
Sonicate fluid cultures (SFC) are more sensitive than conventional microbiological methods in identifying periprosthetic joint infections (PJI), because sonication enables a sampling of the causative bacteria directly from the surface of the endoprosthetic components. Because of their high sensitivity SFC can be positive while all other microbiological methods remain negative. It is therefore difficult to interpret a single SFC as being truly or falsely positive. The aim of this prospective study was to improve the interpretation of SFC in the diagnosis of PJI in patients after total hip arthroplasty through the use of multiple SFC. 102 patients of which 37 had a defined PJI according to the following criteria were included: intraarticular pus or a sinus tract, a periprosthetic membrane (PM) indicative of infection, or a positive microbiological culture in a minimum of 2 separate microbiological samples. A single positive microbiological sample was classified as false positive. In 35 patients multiple SFC were acquired from the separate endoprosthetic components.Introduction
Material and methods
Head sizes used in total hip arthroplasty (THA) has increased drastically from the original 22mm used by Charnley. This is due to two factors: the use of hard-on-hard materials for the bearing articulation and the increasing problem of dislocation. Hard-on-hard materials enable mixed or fluid film lubrication due to their good wettability. The development of a fluid film layer is encouraged by smaller surface pressures (larger area) and higher velocity at the articulating interface (larger radius), suggesting that larger diameters exhibit better lubrication and such less wear. This was effectivly proven in pre-clinical simulator studies and used as argument to increase the diameters of metal-on-metall and ceramic-on-ceramic bearings. Clinically the tribological advantage of larger diameters has not yet been shown. For hard-on-soft bearings the situation is different. Due to the bad wettability of Polyethylene (PE), the abrasive wear regime is dominant. This means that the longer wear path of a larger diameter will inevitably carry a larger amount of wear debris. Despite this relation, the heads used in combination with PE were also increased up to 40mm diameter, justified by the overall greatly reduced wear amount of the new generation(s) of cross-linked PE and favourable simulator results. First in-vivo studies have shown that larger heads carry larger amounts of wear particles. Whether this increase is relevant with respect to osteolysis is still unclear and will have to be shown in longer term studies. Larger heads require a larger “jumping” distance until they dislocate. Consequently the use of larger heads reduces dislocation rates, which was shown in multiple clinical studies. However, the reduction in dislocation rate achieved by increasing diameters varies greatly. Some centres achieve dislocation rates below 1% with 28mm heads, other centres require 36mm heads to achieve the same result. No study shows any further advantage with head diameters larger than 36mm. Despite their obvious biomechanical advantage with regard to stability, larger heads also have large disadvantages. Larger heads carry inevitably larger friction moments, requiring better anchoring of the components. In unfavourable conditions (start-up, break-down of lubrication film), friction moments of hard-on-hard bearings can get very high and reach or even exceed the losening torque of the head on the taper. Depending on the head impaction foce during assembly, the loosening torques amount to 8 to 17Nm. Movement at the head-taper connection possibly causes wear and increased corrosion at this interface. Larger head diameters also require thinner shells and/or liners, leading to problems with liner chipping or incomplete seating. Large head diameters have also lead to the use of sub-hemispherical cups with reduced covering surface, increasing the risk of fluid film break down due to edge loading if not well positioned. Finally, larger heads might give the surgeon a wrong feeling of security regarding a sub-optimal positioned cup. The question regarding “the optimal” head diameter is open for discussion and needs to consider the bearing material used. Head size should be limited to a reasonable compromise, which based on the information currently available, could be 36mm. Join the “36 and under” club.The tribological aspect
The biomechanical aspect
Skeletal muscle injuries often lead to severe functional deficits. Mesenchymal stem cell (MSC) therapy is a promising but still experimental tool in the regeneration of muscle function after severe trauma. One of the most important questions, which has to be answered prior to a possible future clinical application is the ideal time of transplantation. Due to the initial inflammatory environment we hypothesized that a local injection of the cells immediately after injury would result in an inferior functional outcome compared to a delayed transplantation. Twenty-seven female Sprague Dawley rats were used for this study. Bone marrow was aspirated from both tibiae of each animal and autologous MSC cultures obtained from the material. The animals were separated into three groups (each n=9) and the left soleus muscles were bluntly crushed in a standardized manner. In group 1 2×106 MSCs were transplanted into the injured muscle immediately after trauma, whereas group 2 and 3 received an injection of saline. Another week later the left soleus muscles of the animals of group 2 were transplanted with the same number of MSCs. Group 1 and 3 received a sham treatment with the application of saline solution in an identical manner. In vivo functional muscle testing was performed four weeks after trauma to quantify muscle regeneration. Maximum contraction forces after twitch stimulation decreased to 39 ± 18 % of the non injured right control side after crush trauma of the soleus muscles as measured in group 3. Tetanic stimulation showed a reduction of the maximum contraction capacity of 72 ± 12 % of the value obtained from intact internal control muscles. The transplantation of 2 x 106 MSCs one week after trauma improved the functional regeneration of the injured muscles as displayed by significantly higher contraction forces in group 2 (twitch: p = 0.014, tetany: p = 0.018). Local transplantation of the same number of MSCs immediately after crush injury was able to enhance the regeneration process to a similar extent with an increase of maximum twitch contraction forces by 73.3 % (p = 0.006) and of maximum tetanic contraction forces by 49.6 % (p = 0.037) compared to the control group. The presented results underline the effectivity of MSC transplantation in the treatment of severe skeletal muscle injuries. The most surprising finding was that despite of the fundamental differences of the local environment into which MSCs had been transplanted, similar results could be obtained in respect to functional skeletal muscle regeneration. We assume that the effect of the MSC after immediate injection can partly be explained by their known immunomodulatory competences. The data of our study provide evidence for a large time window of MSC transplantation after muscle trauma.
While significant component malalignment in the frontal and sagittal plane may lead to early loosening and pain, even small errors in the rotational component alignment are not tolerated due to its complex impact on knee joint kinematics and especially the patella tracking. It is accepted that navigated implantation of total knee arthroplasties improves accuracy in the frontal plane but it is yet unclear weather navigation leads to a more precise rotational component alignment. The study evaluated the influence of navigated implantation on femoral and tibial component alignment. In a prospective randomized study 32 navigated and 28 conventionally implanted total knee arthroplasties were evaluated through a postoperative CT scan. In all cases the femoral component was referenced to the surgical epicondylar axis and the tibial component was referenced to the medial third of the tibial tuberosity. The angles between these bone landmarks and the components were measured on the CT scans and compared between both study groups. The rotational malalignment of the femoral component in the conventional operating technique was 0.1° ± 2.2° (range 3.3° of internal rotation and 5.0° of external rotation). Navigated implanted femoral components showed a malalignment of 0.3° ± 1.4° (range 4.7° of internal rotation and 2.2° of external rotation), the difference was not significant. The rotational malalignment of the tibial component in the conventional technique was 7.5° ± 6.0° (range 27.1° of internal rotation and 15° of external rotation). Navigated implanted tibial components showed a malalignment of 6.9° ± 4.7° (range 21.2° internal rotation and 11.0° external rotation), the difference was not significant. In conclusion the use of a navigation system did not improve the rotational alignment of the tibial or femoral component if only one bone landmark was used. Taking the relatively small errors of a navigation machine into account the error is attributable to the surgeon, who seems to be unable to precisely define bone landmarks. More than one landmark (e.g. additionally Whiteside’s line, posterior condyles, flexion gap for the femur and ankle joint for the tibia) should be used to define the component rotations. Consideration of different rotational landmarks is best done with a navigation system that, in contrast to the manual technique, has the possibility to show the degree of deviation of the components from each landmark.
Total hip arthroplasty is a challenging problem in case of high hip dislocation. In order to reduce the hip, a femoral shortening osteotomy is necessary to prevent damage to the neurovascular structures. In this study we present the mid-term results of a simple technique of simultaneous derotating and shortening osteotomy of the femur without the necessity of additional osteosynthesis. In this retrospective study we included 28 patients with high hip dislocation. In these patients 30 consecutive cementless primary total hip arthroplasties with femoral shortening osteotomy were performed. 20 cases were previously operated. All patients were clinically and radiologically followed up after a mean of 4.5 years (range 2 – 5.7 years). Time point of consolidation was determined on consecutive radiographs for each patient. The average operative time was 116 minutes (range 65 to 150 minutes). There were no intraoperative complications. Postoperatively no femur fractures, no pseudarthroses and no pareses were observed. The mean consolidation time of the osteotomy was 4.4 months. At the time of follow-up, one aseptic loosening had been verified. In this case a very small stem (size 03) had been used. The mean Merle d’Aubigne score for the unrevised hips improved from 8.2 points preoperatively to 15.1 points at follow-up. In conclusion the presented technique allowed an easy and fast implantation of total hip arthroplasty in patients with high hip dislocation. The Zweymueller stem design with its rectangular cross-section seems responsible for the sufficient stability of the osteotomy resulting in a short consolidation time. Any additional osteosynthesis is obsolete. This leads to additional advantages including a short duration of surgery and a low complication rate. The good clinical results are attributable to the fact, that by shortening the femur, the physiological hip joint biomechanics could be approximated. The mid-term results of the described technique are very promising.
The development of iron oxide nanoparticles, which are taken up and endosomally stored by stem cells, allows the evaluation of cellular behaviour in the muscle with the use of magnetic resonance imaging (MRI). Previous work has shown that labelling does not affect the proliferation and neurogenic differentiation capacity of embryonic stem cells. In the present study we are currently investigating the in vivo distribution and migration of locally transplanted MSC after blunt muscle trauma in a rat model.