Introduction

PIPJ replacement has become increasingly popular however, there is very little clinical data available apart from small studies and those from the originators of the prostheses. We present a review of our initial experience with the Acension^(c) Pyro-carbon PIP joint.

Purpose: Injury to the distal radioulnar joint can result in ulna sided wrist pain and instability. Stabilisation of the distal radioulnar ligaments described by Adams and Berger uses a tendon graft run along the anatomical course of the distal radioulnar ligaments from the lip of the radial sigmoid notch to the fovea of the ulna. The graft wraps around the ulna head and is fixed with a simple suture; this can be challenging for the surgeon and requires a considerable length of tendon. The length of graft required could be reduced by fixing the graft directly to the ulna. Alternative fixation methods when the graft is short would include bone anchors and interference screws.

We therefore compared the fixation strength achieved with simple suture, by bone anchor and by interference screw (Mini Bio-suture Tack and 3mm Biotenodesis interference screw, Arthrex, UK).

Methods: Four ulna bones were harvested along with four corresponding tendons. Tendons were divided into 2mm wide strips and run through a 3.5mm hole in the ulna. Maximum load was measured after fixing the tendon with 1) simple suture, 2) a bone anchor, and 3) an interference screw. Paired data was tested with the paired T-test and Wilcoxon test.

Results: Maximum load recorded was highest for the Mini Bio-Suture Tack bone anchor (99.28 ± 47.39) followed by the simple suture method (96.23 ± 24.14 N), and the Biotenodesis interference screw (46.90 ± 11.29). Differences approached significance when comparing simple suture fixation with interference screws (p=0.02/0.068).

Conclusions: No study has investigated the use of interference screws to secure two tendons in one graft tunnel. Previous work using a single graft and a single tendon has consistently shown that interference screws are superior to other methods of fixation. However, when performing Adam’s procedure for stabilisation of the distal radioulnar joint suturing the tendon together or using a bone anchor provide the greatest fixation strength. This might be due to loss of the interference effect when placing two grafts in the tunnel.

Purpose of Study: To compare the mechanical performance of two commonly used arthroscopic slip knots with that of a hand tied control.

Methods: The arthroscopic slip knots assessed were the Duncan Loop (DL) and the Tautline Hitch (TLH), both of which were tied with arthroscopic knot pushers and secured with Three Reversing Hitches on Alternating Posts (RHAPs). These were compared with four hand tied throws of a squre knot. All three knots were tied using three different materials: number two Ethibond, number one PDS and number two Fiberwire. All knots were tied in a close loop configuration between two metal bars mounted on an Instron materials testing device and pulled apart to both clinical and ultimate failure. Clinical failure was defined as the force in Newtons (N) required to increase loop length by three millimetres, which equtes in vivo with a critical loss in apposition of repaired tissues. Ultimate failure was defined as the force in N resulting in complete slippage or breakage of the knot being tested. This study was different than those before it in that a much larger number of each knot/suture permutation was tested (thirty in each case) to give the study sufficient power to detect significant differences between the knots tested.

Results and Conclusion: Based on the findings of this study, it is our recommendation that an arthroscopic TLH slip knot secured with three RHAPs and tied using a number two Fiberwire suture be used to produce shoulder repairs that are equivalent if not superior to those achieved using open hand tied methods.

Introduction and Aims: The aim was to assess the efficacy of current arthroscopic knotting techniques with commonly used suture materials.

Method: A Hounsfield tensiometer with 1000N load cell, strain rate 25mm/min, bar separation of 7.5mm under standard temperature and pressure was used. Suture materials used, 2 Ethibond, 1 PDS and 1 Panacryl. The knotting techniques compared were the Tennessee slider, Tautline hitch, Duncan Loop, SMC knot and Surgeon’s knot. Two surgeons tied each 10 times using a suture passer and standardised knot technique. Each knot was tested to failure on 10 sequential experiments. Suture material strength was tested in isolation, tested to failure using the different knots then repeated after suture immersion in normal (0.9%) saline.

Results: Ultimate strength of the suture material and the knotting techniques were assessed. The mode of failure, slip or suture material fracture was also investigated. The 2 Ethibond had higher ultimate strength than either 1 PDS or 1 Panacryl. The Tautline hitch and Surgeon’s knot had significantly lower slip rates, with superior internal security than the other knotting techniques (P less than 0.002). The Tennessee slider, Duncan Loop and SMC knots had low security and slipped in more than 50 percent of experiments. There was no difference after saline soaking. The number of additional half hitches required for maximum knot holding capacity was consistently three, confirming previous findings.

Conclusion: The Tautline hitch is recommended due to internal security, tying characteristics and overall knot strength. Whichever knot is selected, three additional alternating half hitches to obtain consistent security is strongly supported.

Aim of Study To assess the efficacy of commonly used sutures materials with commonly described arthroscopic knotting techniques in as close a physiological pattern as possible.

Methods The investigation was carried out in three phases. Initially the ultimate strength of the suture material was tested. Materials compared were 1PDS, 2 Ethibond, 1 Panacryl The suture was then tested to failure by two surgeons comparing five different knotting techniques. Knots tested were Tennessee slider, Duncan loop, SMC, Tautline hitch, and Surgeons knot. Finally the test was repeated after soaking the suture with normal saline.

Results As expected, 2 ethibond has a higher ultimate strength than either 1 PDS or 1 Panacryl. The Tautline hitch and Surgeon’s knot had a significantly lower slippage rate when compared to the other knotting techniques. (P value < 0.002). The Tennessee slider, Duncan Loop and SMC knots slipped in > 50% of experiments. No difference was observed when the suture material had been soaked in normal saline. The number of half hitches required to provide maximum knot holding capacity was 3, confirming previous experimental findings by other investigators.

Conclusions Tautline hitch is recommended for use with all suture materials due to low slippage rates, ease of tying, ease of sliding and overall high knot strength.

Introduction The aim of this study was to assess the efficacy of current arthroscopic knotting techniques with commonly used suture materials.

Methods A Hounsfield tensiometer with a 1000N load cell, strain rate of 25 mm/min, bar separation of 7.5 mm was used under standard temperature and pressure. Suture materials were those in common use; 2 Ethibond, 1 PDS and 1 Panacryl. The knotting techniques compared were the Tennessee slider, Tautline hitch, Duncan Loop, SMC knot and the Surgeon’s knot. Two surgeons tied each knot 10 times using a suture passer and standardised knot technique. Each knot was tested to failure on 10 sequential experiments. Suture material strength was tested alone, tested to failure using the different knots and after suture immersion in normal saline. The ultimate strength of the suture material and of the various knotting techniques were assessed. The mode of failure, slip or suture material fractured was also investigated.

Results The 2 Ethibond had superior strength compared to 1 PDS or 1 Panacryl. The Tautline hitch and Surgeon’s knot had a significantly lower slip rate, with superior internal security than the other knotting techniques (p < 0.002). The Tennessee slider, Duncan Loop and SMC knots slipped in more than 50% of experiments. No difference was observed after soaking in normal saline. The number of additional half hitches required for maximum knot holding was consistently three, confirming previous findings.

Conclusions The Tautline hitch is recommended with its superior internal security, tying characteristics and overall knot strength. Whichever arthroscopic knot is selected, the addition of three alternating half hitches for consistent security and reliability is strongly supported.

87 patients (51 male, 36 female; mean age 57, range 30 to 82) underwent arthroscopic subacromial decompression (SAD) and were followed up for one year. We calculated the ASES, the Constant, the DASH Disability/ Symptom, and the SF-36 Physical Function scores.

All the scores improved throughout the follow-up period, although the SF36 score showed less marked improvement. Comparing the preoperative and one year values there were significant improvements at one year (p < 0.001) for the three upper-limb-specific scoring systems (ASES, Constant and DASH), and for the SF36, but less so (p = 0.001). Comparing the 6 months and one year scores there were significant improvements in the ASES, Constant and DASH scores, but not in the SF36 score. This suggests that improvement may still be continuing at one year.

No significant differences in the postoperative scores for the four acromion operative appearance groups (normal, minor scuffing, marked damage, bare bone areas) were found, or for the operative cuff appearance groups (normal, minor scuffing, partial tear, full thickness tear, massive cuff tear).

We also asked for the patients’ assessment of their outcome at one year, using a satisfaction visual analogue scale (VAS), and two category selection questions relating to satisfaction and to perceived room for further improvement respectively. Patients were coded as successes or failures on their responses to the VAS and the two questions. There seems to be an association with cuff appearance and success or failure as determined by the response to the room for improvement question. More specifically, this difference seems to be due the infraspinatus. A normal infraspinatus is associated with a successful outcome as perceived by the patient.

In conclusion, with SAD recovery may not be complete at one year. The three limb-specific scores are equally useful in monitoring progress, whereas the more general SF36 score is less useful. The state of the acromion or cuff does not have an effect on outcome as measured by the commonly used scores. The appearance of the infraspinatus may be predictive of success as measured by the patient.

The study assesses the efficacy of commonly used suture materials with commonly described arthroscopic knotting techniques in as close a physiological pattern as possible.

The investigation was carried out in three phases. Initially the suture material strength was tested. The suture was then tested to failure using the different knotting techniques. Finally the test was repeated after soaking the suture with normal saline.

A Hounsfield tensometer was utilised with a load cell of 1000N, strain rate of 25mm/min, bar separation of 7.5mm and standard temperature and pressure. Suture material tested was 2 ethibond, 1 PDS and 1 Panacryl. Knotting techniques compared were the Tennessee slider, Tautline hitch, Duncan Loop, SMC knot and Surgeon’s knot. Two surgeons tied each knot 10 times after first becoming practiced with each technique. Each knot was tested to failure on 10 sequential experiments.

Ultimate strength of the suture material and of the knotting techniques was assessed. In addition the mode of failure, whether the knot slipped or suture material fractured was investigated.

As expected, 2 ethibond has a higher ultimate strength than either 1 PDS or 1 Panacryl. The Tautline hitch and Surgeon’s knot had a significantly lower slippage rate when compared to the other knotting techniques. (P value < 0.002). The Tennessee slider, Duncan Loop and SMC knots slipped in more than 50% of experiments. No difference was observed when the suture material had been soaked in normal saline. The number of half hitches required to provide maximum knot holding capacity was 3, confirming previous experimental findings by other investigators.

The Tautline hitch is recommended for use with all suture materials due to low slippage rates, ease of tying, ease of sliding and overall high knot strength