The optimum cementing technique for the tibial
component in cemented primary total knee replacement (TKR) remains
controversial. The technique of cementing, the volume of cement
and the penetration are largely dependent on the operator, and hence
large variations can occur. Clinical, experimental and computational
studies have been performed, with conflicting results. Early implant
migration is an indication of loosening. Aseptic loosening is the
most common cause of failure in primary TKR and is the product of
several factors. Sufficient penetration of cement has been shown
to increase implant stability. This review discusses the relevant literature regarding all aspects
of the cementing of the tibial component at primary TKR. Cite this article:
Oxidized zirconium (OxZr) is used as a ceramic surface for femoral components in total knee arthroplasty (TKA). The aim of this study was to investigate its performance by examining retrieved femoral components and their corresponding PE inserts in matched comparison with conventional chrome/cobalt/molybdenum alloy (CrCoMo). 11 retrieved posterior stabilized (PS) TKA with an OxZr femoral component were included. From a cohort of 56 retrieved TKA with CrCoMo femoral components, pairs were matched according to duration of implantation, patient age, reason for revision, and BMI. The retrieved tibial polyethylene (PE) inserts were analyzed for wear using the Hood classification. Femoral components were optically viewed at 8–32x magnification and screened for scratching, pitting, delamination, and striation. Profilometry was performed to measure surface roughness of the OxZr components using a non-contact white light profiler.Introduction
Methods
The influence of controlled mechanical loading on osseointegration was investigated using an in vivo device implanted in the distal lateral femur of five male rabbits. Compressive loads (1 MPa, 1 Hz, 50 cycles/day, 4 weeks) were applied to a porous coated titanium cylindrical implant (5mm diameter, 2mm width, 75% porosity, 350ìm average pore diameter) and the underlying cancellous bone.. The contralateral limb served as an unloaded control. MicroCT scans at 28 μm resolution were taken of a 4 × 4mm cylindrical region of interest that included cancellous bone below the implant. A scanning electron microscope with a backscattered electron (BSE) detector was used to quantify the percent bone ingrowth and periprosthetic bone in undecalcified sections through the same region of interest. A mixed effects model was used to account for the correlation of the outcome measures within rabbits.. The percent bone ingrowth was significantly greater in the loaded limb (19 +/− 4%) compared to the unloaded control limb (16 +/− 4%, p=0.016) as measured by BSE imaging. The underlying cancellous periprosthetic tissue bone volume fraction was not different between the loaded (0.26 +/− 0.06) and unloaded control limb (0.27 +/− 0.07, p=0.81) by microCT. BSE imaging also showed no difference in the percent area of periprosthetic bone (27 +/− 10% loaded vs. 23 +/− 10% unloaded, p=0.25). Cyclic mechanical loading significantly enhanced bone ingrowth into a titanium porous coated surface compared to the unloaded controls.
The majority of the scientific literature is based on data obtained from elderly cadaveric material. Little is known about the biomechanical properties of the soft tissue grafts currently used prior to implantation. The correct preconditioning and intraoperative tensioning of the soft tissue grafts has also not been investigated. The initial graft biomechanical properties are important. Inadequate tension will lead to continuing instability whilst excessive tension may cause accelerated joint arthrosis. The tension in the graft may decrease by 30% if it has not been cyclically pretensioned.
This device will also allow the accurate preconditioning of the graft, providing objective data that can then be compared to the subsequent clinical progress of the patient. All testing will be accomplished during the time it takes to prepare the tunnels for insertion of the graft, and as such will not prolong unnecessarily the operative time.
This set-up will be immersed in a saline water bath maintained at body temperature during testing. The load cell will be hermetically sealed, with clamps and water bath being autoclavable. With the facilities for draping, the test area will remain sterile. The auto graft clamps will be designed to allow fixation of various graft materials (eg semitendinosus, gracilis, bone-patella tendon-bone) and adjustable for graft lengths. The water bath will house a thermocouple, heating mat and controller to maintain the saline temperature to within 1°C. The testing system will be mounted on a stainless steel trolley for mobility in the operating room with an underlying shelf to house the associated electronics and a retractable side draw for storage of the laptop computer. The autograft will be preconditioned between two known loads for 20 cycles recording load and displacement simultaneously on a laptop computer. Once preconditioned, the autograft will then be used for the ACL reconstruction in the standard way.