Intervertebral disc (IVD) degeneration is inadequately understood due to the lack of in vitro systems that fully mimic the mechanical and biological complexity of this organ. We have recently made an advancement by developing a bioreactor able to simulate physiological, multiaxial IVD loading and maintain the biological environment in ex vivo IVD models [1]. To validate this new bioreactor system, we simulated natural spine movement by loading 12 bovine IVDs under a combination of static compression (0.1 MPa), cyclic flexion/extension (±3˚, ±6˚ or 0-6˚) and cyclic torsion (±2˚, ±4˚ or 0-4˚) for more than 10’000 (0.2 Hz) or 100’000 (1 Hz) cycles over 14 days. A higher number of cycles increased the release of glycosaminoglycans and nitric oxide, as an inflammation marker, whereas fewer cycles maintained these two factors at physiological levels. All applied protocols upregulated the expression of MMP13 in the outermost annulus fibrosus (AF), indicating a collagen degradation response. This was supported by fissures observed in the AF after a longer loading duration. Increasing loading cycles induced high cell death in the nucleus pulposus and inner AF, while with fewer cycles, high cell viability was maintained in all IVD regions, irrespective of the magnitude of rotation. Less frequent multiaxial loading maintains IVD homeostasis while more frequent loading initiates an IVD degenerative profile. Specifically, the morphological and molecular changes were localized in the AF, which can be associated with combined flexion/extension and torsion. More loading cycles induced region-specific cell death and a higher release of extracellular matrix molecules from the innermost IVD regions, likely associated with longer exposure to static compression. Altogether, we demonstrated the advantages of the multiaxial bioreactor to study region-specific response in the IVD, which will allow a more profound investigation of IVD degeneration under different combinations of motions

Decellularised porcine superflexor tendon (pSFT) has been demonstrated to be a suitable scaffold for anterior cruciate ligament reconstruction[1]. While the role of collagen in tendons is well known, the mechanical role of glycosaminoglycans (GAGs) is less clear and may be altered by the decellularisation process. To determine the effects of decellularisation on pSFT GAG content and mechanical function and to investigate the consequences of GAG loss in tensile and compressive loading. pSFTs were decellularised following previous techniques [2]. For GAG removal, native pSFTs were treated with chondroitinase ABC (ChABC; 0.1U/mL, 72h). Cell and GAG removal was validated using histology and quantitative assays. Native, decellularised and ChABC treated groups (n=6) were biomechanically characterised. In tension, specimens underwent stress relaxation and strength testing using previous protocols [1]. Stress relaxation data was fitted to a modified Maxwell-Weichert model to determine time-dependent (E1 & E2) and time-independent moduli (E0). The toe and linear region moduli (Etoe, Elinear), in addition to tensile strength (UTS) and failure strain were determined from strength testing. In compression, specimens underwent confined loading conditions (ramp at 10 s-1 to 10% strain and hold). The aggregate modulus (HA) and zero-strain permeability (k0) were determined using previous techniques [3]. Data was analysed by one-way ANOVA with Tukey post-hoc test to determine significant differences between test groups (p<0.05). Quantitative assays showed no GAG reduction post-decellularisation, but a significant reduction after ChABC treatment. HA was only significantly reduced in the ChABC group. k0 was significantly higher for the ChABC group compared to decellularised. E0 was significantly reduced in the decellularised group compared to native and ChABC groups, while E1 and E2 were not different between groups. Etoe, Elinear, UTS and failure strain were not different between groups. Decellularisation does not affect GAG content or impair mechanical function in pSFT. GAG loss adversely affects pSFT compressive properties, revealing major mechanical contribution under compression, but no significant role under tension

In a healthy joint, mechanical loading increases matrix synthesis and maintains cell phenotype, while reducing catabolic activities. It activates several pathways, most of them yet largely unknown, with integrins, TGF-β, canonical (Erk 1/2) and stress-activated (JNK) MAPK playing a key role. Degenerative joint diseases are characterized by Wnt upregulation and by the presence of proteolytic fibronectin fragments (FB-fs). Despite they are known to impair some of the aforementioned pathways, little is known on their modulatory effect on cartilage mechanoresponsiveness. This study aims at investigating the effect of mechanical loading in healthy and in vitro diseased cartilage models using pro-hypertrophic Wnt agonist CHIR99021 and the pro-catabolic FB-fs 30 kDa. Human primary chondrocytes from OA patients have been grown in alginate hydrogels for one week, prior to be incubated for 4 days with 3μM CHIR99021 or 1 μM FB-fs. Human cartilage explants isolated from OA patients have incubated 4 days with 3 μM CHIR99021 or 1 μM FB-fs. Both groups have then been mechanically stimulated (unconfined compression, 10% displacement, 1.5 hours, 1 Hz), using a BioDynamic bioreactor 5270 from TA Instruments. Expression of collagen type I, II and X, aggrecan, ALK-1, ALK-5, αV, α5 and β1 integrins, TGF-β1 have been assessed by Real Time-PCR and normalized with the expression of S29. Percentage of phosphorylated Smad2, Smad1 and JNK were determined through western blot. TGF-β1 content was quantified by sandwich ELISA; MMP-13 and GAG by western blot and DMMB assay, respectively. At least three biological replicates were used. ANOVA test was used for parametric analysis; Kruskal-Wallis and Mann-Whitney post hoc test for non-parametric. Preliminary data show that compression increased collagen II expression in control, but not in CHIR99021 and FB-fs pre-treated group (Fig. 1A-B). This was associated with downregulation of β1-integrin expression, which is the main collagen receptor and further regulates collagen II expression, suggesting inhibition of Erk1/2 pathway. A trend of increase expression of collagen type X after mechanical loading was observed in CHIR and FB-fs group. ALK-1 and ALK-5 showed a trend toward stronger upregulation in CHIR99021 group after compression, suggesting the activation of both Smad1/5/8 and Smad 2/3 pathways. To further investigate pathways leading to these different mechano-responses, the phosphorylation levels of Smad1 and Smad2, Erk1/2 and JNK proteins are currently being studied. Preliminary results show that Smad2, Smad1 and JNK protein levels increased in all groups after mechanical loading, independently of an increase in TGF-β1 expression or content. Compression further increased phosphorylation of Smad2, but not of Smad1, in all groups

The influence of rigid fixation and permanent compression on the results, the timing of fusion and rehabilitation after fractures of the femoral neck was investigated. A hip fracture is 60–80% of all fractures of the proximal femur. Despite recent advances in the treatment of this disease, the percentage of unsatisfactory outcomes as high as 25–35%. The choice of surgical treatment in femoral neck fractures in the elderly remains as controversial as it was almost 50 years ago when Speed called him as “the unsolved fracture. Hip replacement is currently the gold standard in the treatment of femoral neck fractures. But compared with the osteosynthesis operation takes more time, is accompanied by massive blood loss, sometimes the need for transfusion and a higher risk of deep wound infection. Given these facts the best is an indoor low-traumatic method of osteosynthesis locking. Compare of the results of femoral neck fractures using of osteosynthesis 3 blade nail, spongious screws and nail for permanent compression. A retrospective analysis of treatment of 252 patients from 1982 to 2015 with subcapitale and transcervical fractures of the femoral neck on the basis “RCTO named by H.J. Makazhanova”. In the research locales patients older than 40 years. All patients were divided according to the applied method of treatment: 1 group of 95 patients operated using a 3-blade-nail, in the 2nd group of 105 patients operated on spongious screws, in the 3 group of 52 patients operated nail for the permanent compression, authoring. All patients underwent x-ray examination before and after surgery. The average period from time of injury before performing the osteosynthesis amounted to 4–7 days. The follow-up period was 6–12 months. The results obtained clinically and radiographically divided into good, satisfactory, poor. Good and satisfactory results were regarded as positive, and poor results as negative. The average age of patients was 67.5 years. Among these female patients − 174 (69%), the male − 78 (31%). Traumatization more prone to elderly accounting for 206 (81.7%) cases, and only 46 (18.3%) in the middle age group. Analysis of the results of treatment showed positive results in 1 group − 69.5 %, in group 2 − 83.8 %, in group 3 − 96.2 %. In the first group of 29 (31.5 %) and in the second group of 17 (16.2 %) patients have postoperative complications: secondary displacement, nail migration, pseudarthrosis, necrosis of head. The patients of third group have postoperative complications in 2 cases (3.8 %): displacement of bone fragments according of retraumatization. Employability was restored in 1 group − 7–9 months, in group 2 - in 6–8 months, 3 group - through 6–6.5 months. 1). The method of choice for fresh fractures of the femoral neck, especially subcapital fractures in the elderly, is a minimally invasive method of closed compression osteosynthesis. 2). Comparative analysis of treatment results showed that for the consolidation and subcapital transcervical femoral neck fractures can provide rigid fixation of bone fragments. 3). The use of permanent compression is the best method, which shortens the period of consolidation

Introduction and Objective. The effectiveness of anti-embolic graduated compression stockings (GCSs) has recently been questioned. The aim of this study is to systematically review all the relevant randomised controlled trials published to date. Materials and Methods. We systematically reviewed all the randomised controlled trials comparing anti-embolism stockings with no stockings. We searched the Cochrane Central Register of Controlled Trials, MEDLINE, EMBASE and CINAHL, Cochrane Musculoskeletal Injuries Group specialized register and the reference lists of articles as well as hand search results. Trials were independently assessed and data for the main outcome measures; deep vein thrombosis (DVT), pulmonary embolism and skin ulceration, were extracted by two reviewers. Results. A total of 26 relevant RCTs involving 8279 participants were systematically reviewed. The occurrence of deep vein thrombosis was 306/4159 (7.3%) with the stocking to 492/4120 (11.9%) without the stockings (RR 0.49, 95% CI 0.39–0.62). The occurrence of pulmonary embolism was also reduced from 1.2% to 0.7% (95% 0.33–0.92). This initial finding was unsound due to the potential underreporting of negative studies and the subsequent changes to clinical practice. For the three large contemporary studies involving 5171 participants, these failed to show any statistically significant reduction in thrombosis, with DVT confirmed in 158 (6.1%) participants in those allocated to stocking, as opposed to 171 (6.6%) in the control group. Conclusions. The current recommendations regarding the use of thrombo-embolic stockings need to be reconsidered, as their effectiveness at reducing the occurrence of post-operative deep vein thrombosis is minimal at best, based on the current evidence and clinical practices

Abstract. Objectives. The principle of osteoporotic vertebral compression fracture (OVCF) is fixing instability, providing anterior support, and decompression. Contraindication for vertebroplasty is anterior or posterior wall fracture. The study objectives was to evaluate the efficacy and safety of vertebroplasty with short segmented PMMA cement augmented pedicle screws for OVCF with posterior/anterior wall fracture patients. Methods. A retrospective study of 24 patients of DGOU type-4 (vertebra plana) OVCF with posterior/anterior wall fracture, were treated by vertebroplasty and short segment PMMA cement augmented pedicle screws fixation. Radiological parameters (kyphosis angle and compression ratio) and clinical parameters Visual analogue scale (VAS) and Oswestry disability index (ODI) were analysed. Results. A significant improvement was noted in VAS (preoperative, 7.90 ±0.60; final follow-up 2.90 ± 0.54) and ODI (77.10 ± 6.96 to 21.30 ± 6.70), (P < 0.05). Neurological improvement was noted in all patients. Kyphosis corrected significantly from preoperative 23.20±5.90 to 5.30±1.40 postoperative with 5% (3.30± 2.95) loss of correction at final follow-up. Anterior vertebral height restored significantly from 55.80±11.9% t0 87.6±13.1% postoperative with 4.5±4.0% loss at final follow-up. One case had cement leakage was found, but the patient is asymptomatic. No implant-related complication was seen. No iatrogenic dural or nerve injury. Conclusions. Treatment with vertebroplasty with cement augmented screw fixation and direct decompression is a great option in treating such a complex situation in fragile age with fragile bones because It provides anterior support with cementing that avoids corpectomy. Short segment fixation has less stress risers at the junctional area

Abstract. Objectives. Back pain will be experienced by 70–85% of all people at some point in their lives and is linked with intervertebral disc (IVD) degeneration. The aim of this study was to 1) compare 3D internal strains in degenerate and non-degenerate human IVD under axial compression and 2) to investigate whether there is a correlation between strain patterns and failure locations. Methods. 9.4T MR images were obtained of ten human lumbar IVD. Five were classed as degenerate (Pfirrmann = 3.6 ± 0.3) and five were classed as non-degenerate (Pfirrmann = 2.0 ± 0.2). MR Images were acquired before applying load (unloaded), after 1 kN of axial compression, and after compression to failure using a T2-weighted RARE sequence (resolution = 90 µm). Digital Volume Correlation was then used to quantify 3D strains within the IVDs, and failure locations were determined from analysis of the failure MRIs. Results. Average of axial strains were higher (p<0.05) in the degenerate samples compared to the non-degenerate (−3.4 vs-5.2%, respectively), particularly in the posterior and lateral annulus (−6.2 vs −3.6%, and −5.6 vs −3.5%, respectively). Maximum 3D compressive strains were higher (p<0.05) in the posterior annulus and nucleus regions of the degenerate discs compared to non-degenerate (−9.8 vs −6.2%, and −7.7 vs −5.5%, respectively). In all samples peak tensile and shear strains were observed close to the endplates. All samples failed through the endplates with fractures in the nucleus region in all non-degenerate samples, and fractures in the lateral annulus regions in all degenerate samples. Conclusion. Degeneration caused significant changes to strain distributions within IVDs, particularly at the lateral and posterior AF regions. A shift from endplate failure in the nucleus to the annulus region was observed which was also seen in peak axial internal strains demonstrating a possible correlation between internal IVD strains, and endplate failure locations. Declaration of Interest. (b) declare that there is no conflict of interest that could be perceived as prejudicing the impartiality of the research reported:I declare that there is no conflict of interest that could be perceived as prejudicing the impartiality of the research project

With information about a patient's bone mechanical properties orthopaedic operations could be optimised to reduce intra- and post-operative complications. However, there is currently no reliable method of measuring a patient's bone mechanical properties in vivo. We have previously investigated microindentation, using a 1.5mm diameter spherical indenter tip, and found no correlation between these measurements and compression testing measurements. We hypothesised that by using a larger diameter indenter tip we would closer match bone millimetre-scale mechanical properties. 20 bone samples were taken from 20 patients undergoing hip replacement surgery. The samples were machined from the femoral neck calcar cortical bone into 6×3×3mm parallelepiped specimens, aligned with the osteons along the long axis. The samples were micro-computed tomography (CT) scanned to calculate porosity. Microindentation was performed using a 6mm diameter, sapphire, spherical indenter tip. 12 indentations were performed in a grid and the reduced moduli were calculated using the Oliver-Pharr method. Compression testing was then performed to failure and the apparent elastic modulus was calculated for each sample. A moderate correlation was found between the indentation reduced moduli and compression testing elastic moduli (r=0.52, r2=0.275, p=0.018). In addition, a moderate correlation was found between the indentation reduced moduli and CT-measured porosity (r=0.5, r2=0.251, p=0.025) and a strong correlation was found between compression testing moduli and porosity (r=0.75, r2=0.568, p<0.001). Using large-tip spherical microindentation, indentation reduced moduli correlated significantly with compression testing apparent elastic moduli in these 20 cortical bone specimens. Microindentation using a large, spherical indenter tip may predict the mechanical properties of bone at the millimetre length scale and shows promise as a potential future clinical decision aid in surgery

Background. Bothlimited-contact dynamic compression plate (LC-DCP) and locking compression plate (LCP) systems were designed to provide enhanced bone healing and to improve stability at fracture site. However, implant failure, delayed union, nonunion and instability are still frequently encountered complications. The purpose of this study was to determine the biomechanical characteristics of a novel persistent compression dynamic plate (PCDP) which provides a persistent compression to fracture edges, and to compare the biomechanical properties of such a novel plate with the commonly used LCP. Methods. The novel persistent compression dynamic plate (PCDP) system is composed of a body, an inner compression spring and a distal mobile component. The body (proximal part) contains an adjustable screw and the distal part of the dynamic system can slide inside the body through a special tube. 12 (saw bone) artificial femoral bones were used. Transverse distal shaft fracture was created in all the saw bones at the same level, 6 femurs were fixed using the novel PCDP, whereas the other 6 femurs were fixed using the well-known LCP. All samples had undergone a nondestructive repetitive different forces (axial compression, bending and torsion), to evaluate the biomechanical differences between the two plating systems. Results. Under axial load the mean stiffness value was 439,0 N/mm for the PCDP and 158,9 N/mm for the LCP. There was nosignificant difference in A-P (anteroposterior) ve P-A (posteroanterior) bending stiffness values between PCDP and LCP, P=0.37 and P=0.80 respectively. However LCP provided significantly stiffer fixation in medial and lateral bending tests than PCDP (P=0.037) and (P=0.016), respectively. But no significant difference was detected between the two plating system in the torsional stiffness P=0.15. Conclusion. These results do not show any significant biomechanical difference in the applied torsional and bending stresses between LCP and PCDP. However the remarkably increased persistent compression effect of the PCDP created a considerable stress on fracture edges which may accelerate bone healing. Level of Evidence. Level 5

Summary Statement. The spinal cord showed marked sensibility to acute compression causing complete and irreversible injury. On the contrary, the spinal cord has more ability for adaptation to slow progressive compression mechanisms having the possibility of neural recovery after compression release. Introduction. The aim of this experimental study was to establish, by means of neurophysiologic monitoring, the degree of compression needed to cause neurologic injury to the spinal cord, and analyze whether these limits are different making fast or slow compression. Material and Methods. Spinal cord was exposed from T7 to T11 in 5 domestic pigs with a mean weight of 35 kg. The T8 and T9 spinal roots were also exposed. A pair of sticks, attached to a precise compression device, was set up to both sides of the spinal cord between T8 and T9 roots. Sequentially, the sticks were approximated 0.5 mm every 2 minutes causing progressive spinal cord compression. An acute compression of the spinal cord was also reproduced by a 2.5 mm displacement of the sticks. Cord to cord motor evoked potentials were obtained with two epidural catheters, stimulating proximal to T6 and recording below the compression level, distal to T10, for each sequential approach of the sticks. Results. The mean width of the dural sac was 7.1 mm. For progressive compression, increasing latency and decreasing amplitude of the evoked potentials were observed after a mean displacement of the sticks of 3.2 ± 0.9 mm, the evoked potential finally disappearing after a mean displacement of 4.6 ± 1.2 mm. The potential returned 16.8 ± 3.2 minutes after the compression was stopped in every case. The evoked potentials immediately disappeared after an acute compression 2.5 ± 0.3 mm, without any sign of recovering after 30 minutes. Conclusion. The proposed experimental model replicates the mechanism of a spinal cord injury caused by medially displaced screws into the spinal canal, causing therefore lateral compression to the spinal cord. The spinal cord showed marked sensibility to acute compression, which caused complete and irreversible injury. On the contrary, the spinal cord has more ability for adaptation to progressive and slow compression mechanisms. From a clinical point of view, it seems mandatory to avoid maneuvers of rapid mobilization or acute, even minimal, contusions of the thoracic cord

Summary Statement. Tibia plateau split fracture fixation with two cancellous screws is particularly suitable for non-osteoporotic bone, whereas four cortical lag screws provide a comparable compression in both non-osteoporotic and osteoporotic bone. Angle-stable locking plates maintain the preliminary compression applied by a reduction clamp. Introduction. Interfragmentary compression in tibia plateau split fracture fixation is necessary to maintain anatomical reduction and avoid post-traumatic widening of the plateau. However, its amount depends on the applied fixation technique. The aim of the current study was to quantify the interfragmentary compression generated by a reduction clamp with subsequent angle-stable locking plate fixation in an osteoporotic and non-osteoporotic synthetic human bone model in comparison to cancellous or cortical lag screw fixation. Methods. Adult synthetic human tibiae with hard or soft cancellous bone were osteotomised at the lateral tibia plateau creating a split fracture (AO type 41-B1) and fixed with either two 6.5 mm cancellous, four 3.5 mm cortical lag screws or 3.5 mm LCP proximal lateral tibia plate, preliminary compressed by a reduction clamp (n = 5 per group). Interfragmentary compression was measured by a pressure sensor film after instrumentation. One-way analysis of variance (ANOVA) with Bonferroni post hoc correction was performed for statistical analysis (p < 0.05). Results. Applying a reduction clamp, interfragmentary compression was 0.6 MPa ± 0.1 in non-osteoporotic and osteoporotic bone. The locking plate was able to maintain the compression (0.5 MPa ± 0.1) in non-osteoporotic and osteoporotic bone, but it was significantly lower compared to four cortical lag screws (non-osteoporotic p = 0.01; osteoporotic p = 0.03). Comparing four 3.5 mm cortical lag screws, compression was not significantly different between the non-osteoporotic (1.7 MPa ± 0.7) and osteoporotic bone (1.4 MPa ± 0.5). Two 6.5 mm cancellous lag screws achieved significantly higher compression in non-osteoporotic (2.1 MPa ± 0.6) compared to osteoporotic (0.8 MPa ± 0.2, p = 0.01) bone. Conclusion. Preliminary compression applied by a reduction clamp was maintained by angle-stable locking plates. The two 6.5 mm cancellous screw technique would especially be appropriate for young human non-osteoporotic bone, whereas the four 3.5 mm cortical screw configuration could also be applied in osteoporotic bone

Spinal nerve roots often sustain compression injuries. We used a Wistar rat model of the cauda equina syndrome to investigate such injuries. Rapid transient compression of the cauda equina was produced using a balloon catheter. The results were assessed by daily neurological examination and somatosensory evoked potential (SEP) recording before surgery and ten weeks after decompression. Compression of the spinal nerves induced changes in the SEP which persisted for up to ten weeks after decompression, but it had no effect on the final neurological outcome. Our study shows the importance of early surgical decompression for cauda equina syndrome

Summary. Shear stress and hydrostatic effects on the hMSCs early mechano gene response were similar. For the same magnitude gene response, the hydrostatic compression (1.5×10. 5. Pascal) is a 200000 times greater than the force exerted by shear stress (0.7 Pascal). Introduction. In the lab, a perfusion bioreactor designed to automate the production of bone constructs was developed. The proof of concept was established in a large animal model of clinical relevance. The cells perfused in the bioreactor are likely to perceive 2 types of stresses: shear stress and hydrostatic pressure. Optimization of this bioreactor implies a better understanding of the effects of these forces on the cells in order to have better proliferation and differentiation. An understanding of the response of one cell layer submit to various strength is relevant. The primary objective of this study was to test the hypothesis that hMSCs have the fundamental ability to distinguish between different types of mechanical signals as evidenced by distinct gene expression. The effect of shear stress on one cell layer cultures of hMSCs will be evaluated using a commercially available system called Ibidi. For the hydrostatic pressure as there is no commercial device available, our group has developed a prototype capable of delivering a well-defined mechanical loading to cells in culture. Validation of the techniques: In order to validate the systems (shear stress and cyclic pressure apparatus) used in this study, we have used an osteocytes-like cell line, MLO-Y4. When stimulated by a 30 minutes PFF at 7 dyn/cm. 2. or hydrostatic compression at 1.5 bar, cells responded by producing NO in the culture media. NO release after mechanical stimulation of hMSCs: hMSCs were subjected to increased PFF (7 to 42 dyn/cm. 2. ) for 30 minutes. This stimulation resulted in an increased release of NO in the media compared to non-stimulated cells (p<0.05). Interestingly the level of NO was maximal at 7 dyn/cm. 2. and decreased with higher flow rate. Similar observation was made after hMSCs stimulation by hydrostatic pressure for 30 minutes: a peak of NO release at 1.5 bar was observed. Early gene expression of known mechano-sensitive genes: Gene expression analysis immediately after stimulation (PFF or hydrostatic compression) was performed on a range of known mechano-sensitive genes: NOS2, PTGS2, PTGES, IER3 and EGR1. Immediately after stimulation by PFF at 7 dyn/cm. 2. or hydrostatic pressure at 1.5 bars, the expression of all the genes of interest appear to be up regulated in stimulated cells. Conclusions. In the present study, hMSCs cells responses to two different treatments, shear stress and hydrostatic pressure, were monitored in parallel to study the difference in sensitivity to both mechanical stresses. Both systems used ensure a stable and reproducible strain condition in a well-controlled environment. We demonstrated that the shear stress and the hydrostatic pressure effects on the hMSCs were similar. We note that, for the same magnitude response, force exerted by the hydrostatic compression (1.5×10. 5. Pascal) on the cells is a 200000 times greater than the force exerted by shear stress (0.7 Pascal). This shows that the direct effect of hydrostatic compression on the hMSCs is negligible compared to the shear stress

Introduction. In recent years, there has been a growing interest, in many fields of medicine, in the use of bone adhesives that are biodegraded to non-toxic products and resorbed after fulfilling their function in contact with living tissue. Biomechanical properties of newly developed bone glue, such as adhesion to bone and elastic modulus were tested in our study. Material and methods. Newly developed injectable biodegradable “self-setting” bone adhesive prepared from inorganic tricalcium phosphate powder and aqueous solution of organic thermogelling polymers was used for ex-vivo fixing fractured pig femur. Ex-vivo biomechanical tests were performed on 45 fresh pig femurs. Control group consist of 10 healthy bones, tested group was created by 35 bones with artificial fractures in diaphysis – oblique (O) and bending wedge (BW) type of fracture. Tested group were divided to following 4 subgroups (sg); sg1 – O fracture (n=15) glued together with 3 different type of bone adhesives, sg2 BW fracture (n=5) glued together with bone adhesive (n=5); sg3 – BW fracture fixed with locking compression plate (LCP), n=5; sg4 – BW fracture fixed with LCP in combination with bone adhesive. Three-point bending force and shear compression tests were performed on linear electrodynamic test instrument (ElectroPuls E10000, Instron). Femurs from sg1, sg2 and sg4 were tested on Micro-CT before and after biomechanical testing. Results. Shear compression tests in sg1 without amino acids modification showed that it is needed force of 0.5 mPa to recreate fracture, however, modification with amino acids increased glue strength to 3 mPa. Three-point bending force test in sg2 showed reduced force of 250 N to recreate fracture, anyhow in sg4 force needed to initiate the fracture was increased up to 5000 N. Conclusion. Newly developed injectable biodegradable “self- setting” bone adhesive represents new possibility how to fix small bone fragments in comminuted fractures and simultaneous chance how to improve and accelerate bone healing process. Acknowledgement. Project no. AOTEU-R-2016-064 was supported by AOTRAUMA, Switzerland

There is a growing trend towards using pre-clinical models of atrophic non-union. This study investigated different fixation devices, by comparing the mechanical stability at the fracture site of tibia bone fixed by either intramedullary nail, compression plate or external fixator. 40 tibias from adult male Wistar rats' cadavers were osteotomised at the mid-shaft and a gap of 1 mm was created and maintained at the fracture site to simulate criteria of atrophic non-union model. These were divided into five groups (n=8 in each): the first group was fixed with 20G intramedullary nail, the second group with 18G nail, the third group with 4-hole plate, the fourth group with 6-hole plate, and the fifth group with external fixator. Tibia was harvested by leg disarticulation from the knee and ankle joints, the soft tissues were carefully removed from the leg, and tibias were kept hydrated throughout the experiment. Each group was then subdivided into two subgroups for mechanical testing: one for axial loading (n=4) and one for 4-point bending (n=4). Statistical analysis was carried out by ANOVA with a fisher post-hoc comparison between groups. A p-value less than 0.05 was considered statistically significant. Axial load to failure data and stiffness data revealed that intramedullary nails are significantly stronger and stiffer than other devices, however there was no statistically significant difference axially between the nail thicknesses. In bending, load to failure revealed that 18G nails are significantly stronger than 20G. We concluded that 18G nail is superior to the other fixation devices, therefore it has been used for in-vivo experiments to create a novel model of atrophic non-union with stable fixation

There is a growing trend towards using pre-clinical models of atrophic non-union. This study investigated different fixation devices, by comparing the mechanical stability at the fracture site of tibia bone fixed by either intramedullary nail, compression plate or external fixator. 40 tibias from adult male Wistar rats' cadavers were osteotomised at the mid-shaft and a gap of 1 mm was created and maintained at the fracture site to simulate criteria of atrophic non-union model. These were divided into five groups (n=8 in each): the first group was fixed with 20G intramedullary nail, the second group with 18G nail, the third group with 4-hole plate, the fourth group with 6-hole plate, and the fifth group with external fixator. Tibia was harvested by leg disarticulation from the knee and ankle joints, the soft tissues were carefully removed from the leg, and tibias were kept hydrated throughout the experiment. Each group was then subdivided into two subgroups for mechanical testing: one for axial loading (n=4) and one for 4-point bending (n=4). Statistical analysis was carried out by ANOVA with a fisher post-hoc comparison between groups. A p-value less than 0.05 was considered statistically significant. Axial load to failure data and stiffness data revealed that intramedullary nails are significantly stronger and stiffer than other devices, however there was no statistically significant difference axially between the nail thicknesses. In bending, load to failure revealed that 18G nails are significantly stronger than 20G. We concluded that 18G nail is superior to the other fixation devices, therefore it has been used for in-vivo experiments to create a novel model of atrophic non-union with stable fixation

Summary Statement. Repetitive loading of degenerated human intervertebral discs in combined axial compression, flexion and axial rotation, typical of manual handling lifing activities, causes: an increase in intradiscal maximum shear strains, circumferential annular tears and nuclear seperation from the endplate. Introduction. Chronic low back pain (LBP) is a crippling condition that affects quality of life and is a significant burden to the health care system and the workforce. The mechanisms of LBP are poorly understood, however it is well known that loss of intervertebral disc (disc) height due to degeneration is a common cause of chronic low back and referred pain. Gross disc injury such as herniation can be caused by sudden overload or by damage accumulation via repetitive loading, which is a cause of acute LBP and an accelerant of disc degeneration. The aim of this study was to determine for the first time the relationship between combined repetitive compression, flexion and axial rotation motion of degenerated cadaver lumbar spine segments, and the progression of three-dimensional (3D) internal disc strains that may lead to disc herniation and macroscopic tissue damage. Patients & Methods. Seven degenerated human lumbar functional spinal units (FSUs) underwent pre-test MRI, had a grid of tantalum wires inserted into the mid-transverse plane of the disc and were subjected to 20,000 cycles of repetitive loading in combined compression (1.7 MPa), flexion (11–13°) and right axial rotation (2–3°) in a six degree of freedom hexapod robot. Stereoradiographs were taken at cyclic intervals (1, 500, 1000, 5000, 10000, 15000 and 20000 cycles) from which 3D intradiscal principal strains and maximum shear strains (MSS) were calculated and partitioned into nine disc anatomical regions. After testing the discs underwent post-test MRI followed by macroscopic assessment to identify tissue damage. A repeated measures ANOVA having a within-subjects factor of cycle number, and a between-subjects factor of disc region was used to examine the effects of cycle number and disc region on MSS. Results. No visible evidence of disc herniation occurred after 20,000 cycles, however circumferential annular tears and nucleus separation from the endplate were observed in all specimens in agreement with observed signal changes in post-test MRI images. There was a significant effect of both cycle number, disc region and the interaction of cycle number x disc region on MSS (p<0.001). MSS was significantly larger after 20,000 cycles compared with the first loading cycle in the anterior, left anterolateral, left lateral, and left posterolateral disc regions (p<0.037). Minor changes in MSS were seen in the posterior and nucleus regions. The largest increases were observed in the left anterolateral and left posterolateral regions after 20,000 cycles. Discussion/Conclusion. A significant increase in MSS was observed across most regions in the disc after 20,000 repetitive loading cycles, especially in the left anterolateral and left posterolateral regions. No herniation was observed, although macroscopic and MRI evidence of circumferential annular tears and nuclear separation from the endplate occurred, suggesting internal disc tissue disorganisation that may indicate a progression towards eventual herniation

Summary. Biomechanically, a 2° screw deviation from the nominal axis in the PFLCP leads to significantly earlier implant failure. Screw deviation relies on a technical error on insertion, but in our opinion cannot be controlled intraoperatively with the existing instrumentation devices. Background. Several cases of clinical failure have been reported for the Proximal Femoral Locking Compression Plate (PFLCP). The current study was designed to investigate the failure mode and to explore biomechanically the underlying mechanism. Specifically, the study sought to determine if the observed failure was due to technical error on insertion or due to implant design. Methods. To exclude patient and fracture type related factors, an abstract foam block model simulating an unstable pertrochanteric fracture was created for three study groups with six specimens each (n=6). Group 1 was properly instrumented according to the manufacturer's guidelines. In Group 2 and 3, the first or second screw was placed in a posterior or anterior off-axis orientation by 2° measured in the transversal plane, respectively. Each construct was tested cyclically until failure using a test setup and protocol simulating complex axial and torsional loading. Radiographs were taken prior to and after the tests. Force, number of cycles and failure mode were compared. Results. The 2° screw deviation from the nominal axis led to significantly earlier construct failure in Group 2 and 3. The failure mode consisted of loosening of the off-axis screw due to disengagement with the plate, resulting in loss of construct stiffness and varus collapse of the fracture. Conclusions. In our biomechanical test setup, a screw deviation of only 2° from the nominal axis consistently led to the failure mode observed clinically. In our opinion, screw deviation mostly relies on technical error on insertion. But, proper screw insertion may be difficult or impossible with the existing instrumentation devices, especially as it cannot be controlled or guaranteed intraoperatively

Demographics changes and the increasing incidence of metastatic bone disease are driving the significant issues of vertebral body (VB) fractures as an important consideration in the quality of life of the elderly. Whilst osteoporotic vertebral fractures have been widely studies both clinically and biomechanically, those fractures arising from metastatic infiltration in the spine are relatively poorly understood. Biomechanical in-vitro assessment of these structurally weaker specimens is an important methodology for gaining an understanding of the mechanics of such fractures in which a key aspect is the development of methodologies for predicting the failure load. Here we report on a method to predict the vertebral strength by combining computed tomography assessment with an engineering beam theory as an alternative to more complex finite element analyses and its verification within a laboratory scenario. Ninety-two human vertebral bodies with 3 different pathologies: osteoporosis, multiple myeloma (MM) and specimens containing cancer metastases were loaded using a define protocol and the failure loads recorded. Analysis of the resulting data demonstrated that the mean difference between predicted and experimental failure loads was 0.25kN, 0.41kN and 0.79 kN, with adjunct correlation coefficients of 0.93, 0.64 and 0.79 for osteoporotic, metastatic and MM VBs, respectively. Issues in predicting vertebral fracture arise from extra-vertebral bony formations which add to vertebral strength in osteoporotic VB but are structurally incompetent in metastatic disease. The methodology is currently used in providing better experimental design/benchmarking within in-vitro investigations together with further exploration of its utility in the clinical arena.

The aim of this randomised, controlled in vivo study in an ovine model was to investigate the effect of cylic pneumatic pressure on fracture healing. We performed a transverse osteotomy of the right radius in 37 sheep. They were randomised to a control group or a treatment group where they received cyclic loading of the osteotomy by the application of a pressure cuff around the muscles of the proximal forelimb. Sheep from both groups were killed at four or six weeks. Radiography, ultrasonography, biomechanical testing and histomorphometry were used to assess the differences between the groups. The area of periosteal callus, peak torsional strength, fracture stiffness, energy absorbed over the first 10° of torsion and histomorphometric analysis all showed that the osteotomies treated with the cyclic pneumatic pressure at four weeks were not significantly different from the control osteotomies at six weeks.