The importance of cup position on the performance of total hip replacements (THR) has been demonstrated in Pelvic movement data for walking for 39 unilateral THR patients was acquired (Leeds Biomedical Research Centre). Patient's elected walking speed was used to group patients into high- and low-functioning (mean speed, 1.36(SD 0.09)ms−1 and 0.85(SD 0.08)ms−1 respectively). A computational algorithm (Python3.7) was developed to calculate cup version during gait cycle. Inputs were pelvic angles and initial cup orientation (assumed to be 45° inclination and 7° version, anterior pelvic plane was parallel to radiological frontal plane). Outputs were cup version angles during a gait cycle (101 measurements/cycle). Minimum, maximum and average cup version during gait cycle were measured for each patient. Two-sample t-test (p=0.05) was used to compare groups.Abstract
Objectives
Methods
Clavicle fractures are common, yet debate exists regarding which patients would benefit from conservative versus operative management. Traditionally shortening greater than 2cm has been accepted as an indicator for surgery. However, clavicle length varies between individuals. In a cadaveric study clavicle shortening greater than 15% was suggested to affect outcomes. There is no clinical correlation of this in the literature. In this study we investigate outcomes following middle third clavicle fractures and the effect of percentage shortening on union rates. We identified a consecutive series of adults with primary midshaft clavicle fractures presenting to our institution from April 2015-March 2017. Clinical records and radiographs were reviewed to elicit outcomes. Time to union was measured against factors including; percentage shortening, displacement, comminution and smoking. Statistical significance was calculated.Abstract
Objectives
Methods
The mechanisms underlying abnormal joint mechanics are poorly understood despite it being a major risk factor for developing osteoarthritis. This study investigated the response of a 3D in vitro bone cell model to mechanical load. Human MSC cells (Y201) embedded in 3D type I collagen gels were differentiated in osteogenic media for 7-days in deformable, silicone plates. Gels were loaded once (5000 µstrain, 10Hz, 3000 cycles), RNA extracted 1-hr post load and assessed by RT-qPCR and RNAseq analysis (n=5/treatment). Cell shape and phenotype were assessed by immunocytochemistry and phalloidin staining. Data was analysed by Minitab.Abstract
Objectives
Methods
A pilon fracture is a severe ankle joint injury caused by high-energy trauma, typically affecting men of working age. Although relatively uncommon (5% to 7% of all tibial fractures), this injury causes among the worst functional and health outcomes of any skeletal injury, with a high risk of serious complications and long-term disability, and with devastating consequences on patients’ quality of life and financial prospects. Robust evidence to guide treatment is currently lacking. This study aims to evaluate the clinical and cost-effectiveness of two surgical interventions that are most commonly used to treat pilon fractures. A randomized controlled trial (RCT) of 334 adult patients diagnosed with a closed type C pilon fracture will be conducted. Internal locking plate fixation will be compared with external frame fixation. The primary outcome and endpoint will be the Disability Rating Index (a patient self-reported assessment of physical disability) at 12 months. This will also be measured at baseline, three, six, and 24 months after randomization. Secondary outcomes include the Olerud and Molander Ankle Score (OMAS), the five-level EuroQol five-dimenison score (EQ-5D-5L), complications (including bone healing), resource use, work impact, and patient treatment preference. The acceptability of the treatments and study design to patients and health care professionals will be explored through qualitative methods.Aims
Methods
Excessive standing posterior pelvic tilt (PT), lumbar spine stiffness, low pelvic Incidence (PI), and severe sagittal spinal deformity (SSD) have been linked to increased dislocation rates. We aimed to compare the prevalence of these 4 parameters in unstable and stable primary Total Hip Arthroplasty (THA) patients. In this retrospective cohort study, 40 patients with instability following primary THA for osteoarthritis were referred for functional analysis. All patients received lateral X-rays in standing and flexed seated positions to assess functional pelvic tilt and lumbar lordosis (LL). Computed tomography scans were used to measure pelvic incidence and acetabular cup orientation. Literature thresholds for “at risk” spinopelvic parameters were standing pelvic tilt ≤ −10°, lumbar flexion (LLstand – LLseated) ≤ 20°, PI ≤ 41°, and sagittal spinal deformity (PI – LLstand mismatch) ≥ 10°. The prevalence of each risk factor in the dislocation cohort was calculated and compared to a previously published cohort of 4042 stable THA patients.Introduction
Methods
A comprehensive classification for coronal lower limb alignment with predictive capabilities for knee balance would be beneficial in total knee arthroplasty (TKA). This paper describes the Coronal Plane Alignment of the Knee (CPAK) classification and examines its utility in preoperative soft tissue balance prediction, comparing kinematic alignment (KA) to mechanical alignment (MA). A radiological analysis of 500 healthy and 500 osteoarthritic (OA) knees was used to assess the applicability of the CPAK classification. CPAK comprises nine phenotypes based on the arithmetic HKA (aHKA) that estimates constitutional limb alignment and joint line obliquity (JLO). Intraoperative balance was compared within each phenotype in a cohort of 138 computer-assisted TKAs randomized to KA or MA. Primary outcomes included descriptive analyses of healthy and OA groups per CPAK type, and comparison of balance at 10° of flexion within each type. Secondary outcomes assessed balance at 45° and 90° and bone recuts required to achieve final knee balance within each CPAK type.Aims
Methods
The reduction in mobility due to hip diseases in children is likely to affect their physical activity (PA) levels. Physical inactivity negatively influences quality of life and health. Our aim was to objectively measure PA in children with hip disease, and correlate it with the Patient-Reported Outcomes Measurement Information System (PROMIS) Mobility Score. A total of 28 children (12 boys and 16 girls) with hip disease aged between 8and 17 years (mean 12 (SD 3)) were studied between December 2018 and July 2019. Children completed the PROMIS Paediatric Item Bank v. 2.0 – Mobility Short Form 8a and wore a hip accelerometer (ActiGraph) for seven consecutive days. Sedentary time (ST), light PA (LPA), moderate to vigorous PA (MVPA), and vigorous PA were calculated from the accelerometers' data. The PROMIS Mobility score was classified as normal, mild, and moderate functions, based on the PROMIS cut scores on the physical function metric. A one-way analysis of covariance (ANCOVA) was used to assess differences among mobility (normal; mild; moderate) and measured PA and relationships between these variables were assessed using bivariate Pearson correlations.Aims
Methods
The aim of this study was to compare robotic arm-assisted bi-unicompartmental knee arthroplasty (bi-UKA) with conventional mechanically aligned total knee arthroplasty (TKA) in order to determine the changes in the anatomy of the knee and alignment of the lower limb following surgery. An analysis of 38 patients who underwent TKA and 32 who underwent bi-UKA was performed as a secondary study from a prospective, single-centre, randomized controlled trial. CT imaging was used to measure coronal, sagittal, and axial alignment of the knee preoperatively and at three months postoperatively to determine changes in anatomy that had occurred as a result of the surgery. The hip-knee-ankle angle (HKAA) was also measured to identify any differences between the two groups.Aims
Methods
A proximal femur fracture (PFF) is a common orthopaedic presentation, with an incidence of over 25,000 cases reported in the Australian and New Zealand Hip Fracture Registry (ANZHFR) in 2018. Hip fractures are known to have high mortality. The purpose of this study was to determine the utility of the Clinical Frailty Scale (CFS) in predicting 30-day and one-year mortality after a PFF in older patients. A retrospective review of all fragility hip fractures who met the inclusion/exclusion criteria of the ANZHFR between 2017 and 2018 was undertaken at a single large volume tertiary hospital. There were 509 patients included in the study with one-year follow-up obtained in 502 cases. The CFS was applied retrospectively to patients according to their documented pre-morbid function and patients were stratified into five groups according to their frailty score. The groups were compared using Aims
Methods
Up to 40% of patients are using opioids at the time of joint replacement surgery in the USA despite emerging evidence suggesting opioids are ineffective for chronic non-cancer pain. Our primary objective was to determine if preoperative opioid use among patient awaiting total knee arthroplasty (TKA) was associated with worse patient-reported outcomes (PRO) measures at one-year follow-up when compared to non-opioid users, after adjusting for age, gender, and comorbidities. The study linked Alberta's Pharmacy Information Network (PIN) data with prospectively collected Alberta Bone and Joint Health Repository administrative data (medical and PRO data) for patients who underwent primary TKA in Alberta from 2013–2015. The PIN contains prescribing information from physician offices and pharmacies across Alberta. Preoperative ‘opioid users’ were defined as having 90-days of consistent opioid use in the 180-days prior TKA, and ‘opioid-exposed’ subjects had recorded opioid prescriptions in the 180-days prior to TKA, but did not meet the definition of an opioid user. Those with no opioid-exposure in the 180-days pre-TKA were deemed a ‘non-opioid user’. We used multiple linear regression to examine how preoperative opioid use (opioid user, opioid-exposed, non-opioid user) impacted Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC) pain and function scores at one year after TKA after adjusting for confounding variables. These included age, sex, preoperative WOMAC scores, comorbidities including depression, diabetes, obesity, stroke, pulmonary disease, renal disease, cardiac disease, liver disease, and overall comorbid burden. Of the 2182 unique cases identified, 151 (7%) were opioid users, 527 (24%) opioid-exposed and 1504 (69%) non-opioid user. Opioid users were more likely to be prescribed strong opioids (e.g., hydromorphone, oxycodone) compared to with opioid-exposed subjects (p < 0 .001) and had a median morphine equivalent dose of 30.7 mg/day compared with the opioid-exposed group (2.2 mg/day, p < 0 .001) in the 180-days prior to TKA. Opioid users, in the 180-days prior to TKA had an active opioid prescription for a mean duration of 153 days (95CI 149, 157) within the 180-days prior to TKA, compared to 34 days (95CI 32, 37) for opioid-exposed (p < 0 .001). In the parsimonious pain and function models, opioid use, lower preoperative WOMAC score, depression, and obesity were associated with worse one-year pain and function. Patients prescribed preoperative opioids had worse WOMAC scores one-year after TKA respectively when compared to non-opioid users, after adjusting for other factors (opioid user pain score: −9.5, function score: −9.4, opioid exposed pain score: −2.6, function score: −3.6, p < 0 .001 for all). Further, opioid users with a concomitant diagnosis of depression had significantly worse one-year postoperative WOMAC scores when compared to non-depressed non-opioid users (scores −14, p < 0 .001 for both pain and function). In Alberta, 31% of patients were prescribed opioids within 180-days before TKA, preoperative opioid use was associated with worse one-year postoperative WOMAC pain and function scores relative to non-opioid users. Our results suggest that strategies to reduce preoperative opioid use could improve patient outcomes after TKA, and support the most recent Canadian opioid prescribing guidelines that attempt to minimize opioid use for chronic conditions such as arthritis.
Total joint arthroplasty (TJA) is often utilized to improve pain and dysfunction associated with end-stage osteoarthritis. Previous research has suggested that depression may negatively impact patient reported pain and function. The purpose of this study was to determine the effect of pre-operative depressive symptoms, using the Center for Epidemiologic Scale for Depression (CES-D) scale, on patient reported function and pain at one, three and six months following TJA, after controlling for the impact of age, sex, pain, joint replaced, and other comorbidities. This was a secondary analysis of a prospective cohort of 710 patients aged 40 years and older who underwent elective primary TJA in the Edmonton zone. Participants were recruited pre-operatively and reported socio-demographics, comorbid conditions and medications (including depression medications where appropriate), each participant also completed the Western Ontario McMaster (WOMAC) Osteoarthritis Index and the CES-D scale preoperatively. Participants then completed the WOMAC and CES-D scale again at one, three, and six months postoperatively. Risk-adjusted longitudinal data analysis using a linear mixed regression model was performed, controlling for age, sex, joint replaced, chronic pain, comorbidity, social support and employment status. THA participants had a mean age of 65.9±10.1 years and included 175 (57%) female while TKA participants had a mean age of 67.9±10.1 years and included 249 (61%) females. ‘Possible’ depressive symptoms (CES-D score 16–19) were identified in 58 (8.1%) participants while ‘probable’ depressive symptoms (CES-D score ≥20) were identified in 68 (9.6%) participants. The mean WOMAC pain and function scores, when analyzed using the linear mixed regression model, demonstrated improvement from baseline at one, three, and six months (p < 0 .001 for both pain and function models as well as over time). However, in the patients with possible and probable depressive symptoms, WOMAC pain scores were 7.6±1.5 and 11.7±1.3 worse respectively than those without depressive symptoms after controlling for age, sex, joint replaced, chronic pain, comorbidities and social support. Similarly, WOMAC function scores in the patients with possible and probable depressive symptoms were 8.8±1.4 and 14.2±1.2 worse respectively than those without depressive symptoms after controlling for age, sex, joint replaced, comorbidities and employment status. Depressive symptoms negatively affect postoperative pain and function measured using WOMAC scales even after risk adjustment up to six-months post TJA. Screening for depressive symptomology both pre- and postoperatively may provide an opportunity to identify and manage depressive symptoms to improve postoperative pain and function.
An algorithm to determine the constitutional alignment of the lower limb once arthritic deformity has occurred would be of value when undertaking kinematically aligned total knee arthroplasty (TKA). The purpose of this study was to determine if the arithmetic hip-knee-ankle angle (aHKA) algorithm could estimate the constitutional alignment of the lower limb following development of significant arthritis. A matched-pairs radiological study was undertaken comparing the aHKA of an osteoarthritic knee (aHKA-OA) with the mechanical HKA of the contralateral normal knee (mHKA-N). Patients with Grade 3 or 4 Kellgren-Lawrence tibiofemoral osteoarthritis in an arthritic knee undergoing TKA and Grade 0 or 1 osteoarthritis in the contralateral normal knee were included. The aHKA algorithm subtracts the lateral distal femoral angle (LDFA) from the medial proximal tibial angle (MPTA) measured on standing long leg radiographs. The primary outcome was the mean of the paired differences in the aHKA-OA and mHKA-N. Secondary outcomes included comparison of sex-based differences and capacity of the aHKA to determine the constitutional alignment based on degree of deformity.Aims
Methods
Cam morphology develops during adolescence and predisposes individuals to future hip pain and osteoarthritis. An improved understanding of cam development is required to determine whether the process is modifiable. The aim of this study was to characterise the risk factors, timing, and pathogenesis of cam formation.Background
Hypothesis/Purpose
Total joint arthroplasty (TJA) is often utilized to improve pain and dysfunction associated with end-stage osteoarthritis. Previous research has suggested that depression may negatively impact patient reported pain and function. The purpose of this study was to determine the effect of preoperative depressive symptoms, using the Center for Epidemiologic Scale for Depression (CES-D) scale, on patient reported function and pain at one, three and six months following TJA, after controlling for the impact of age, sex, pain, joint replaced, and other comorbidities. This was a secondary analysis of a prospective cohort of 710 patients aged 40 years and older who underwent elective primary TJA in the Edmonton zone. Participants were recruited pre-operatively and reported socio-demographics, comorbid conditions and medications (including depression medications where appropriate), each participant also completed the Western Ontario McMaster (WOMAC) Osteoarthritis Index and the CES-D scale preoperatively. Participants then completed the WOMAC and CES-D scale again at one, three, and six months postoperatively. Risk-adjusted longitudinal data analysis using a linear mixed regression model was performed, controlling for age, sex, joint replaced, chronic pain, comorbidity, social support and employment status. THA participants had a mean age of 65.9±10.1 years and included 175 (57%) female while TKA participants had a mean age of 67.9±10.1 years and included 249 (61%) females. ‘Possible’ depressive symptoms (CES-D score 16–19) were identified in 58 (8.1%) participants while ‘probable’ depressive symptoms (CES-D score ≥20) were identified in 68 (9.6%) participants. The mean WOMAC pain and function scores, when analyzed using the linear mixed regression model, demonstrated improvement from baseline at one, three, and six months (p < 0 .001 for both pain and function models as well as over time). However, in the patients with possible and probable depressive symptoms, WOMAC pain scores were 7.6±1.5 and 11.7±1.3 worse respectively than those without depressive symptoms after controlling for age, sex, joint replaced, chronic pain, comorbidities and social support. Similarly, WOMAC function scores in the patients with possible and probable depressive symptoms were 8.8±1.4 and 14.2±1.2 worse respectively than those without depressive symptoms after controlling for age, sex, joint replaced, comorbidities and employment status. Depressive symptoms negatively affect postoperative pain and function measured using WOMAC scales even after risk adjustment up to six-months post TJA. Screening for depressive symptomology both pre- and postoperatively may provide an opportunity to identify and manage depressive symptoms to improve postoperative pain and function.
Up to 40% of patients are using opioids at the time of joint replacement surgery in the USA despite emerging evidence suggesting opioids are ineffective for chronic non-cancer pain. Our primary objective was to determine if preoperative opioid use among patient awaiting total knee arthroplasty (TKA) was associated with worse patient-reported outcomes (PRO) measures at one-year follow-up when compared to non-opioid users, after adjusting for age, gender, and comorbidities. The study linked Alberta's Pharmacy Information Network (PIN) data with prospectively collected Alberta Bone and Joint Health Repository administrative data (medical and PRO data) for patients who underwent primary TKA in Alberta from 2013–2015. The PIN contains prescribing information from physician offices and pharmacies across Alberta. Preoperative ‘opioid users’ were defined as having 90-days of consistent opioid use in the 180-days prior TKA, and ‘opioid-exposed’ subjects had recorded opioid prescriptions in the 180-days prior to TKA, but did not meet the definition of an opioid user. Those with no opioid-exposure in the 180-days pre-TKA were deemed a ‘non-opioid user’. We used multiple linear regression to examine how preoperative opioid use (opioid user, opioid-exposed, non-opioid user) impacted Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC) pain and function scores at one year after TKA after adjusting for confounding variables. These included age, sex, preoperative WOMAC scores, comorbidities including depression, diabetes, obesity, stroke, pulmonary disease, renal disease, cardiac disease, liver disease, and overall comorbid burden. Of the 2182 unique cases identified, 151 (7%) were opioid users, 527 (24%) opioid-exposed and 1504 (69%) non-opioid user. Opioid users were more likely to be prescribed strong opioids (e.g., hydromorphone, oxycodone) compared to with opioid-exposed subjects (p < 0 .001) and had a median morphine equivalent dose of 30.7 mg/day compared with the opioid-exposed group (2.2 mg/day, p < 0 .001) in the 180-days prior to TKA. Opioid users, in the 180-days prior to TKA had an active opioid prescription for a mean duration of 153 days (95CI 149, 157) within the 180-days prior to TKA, compared to 34 days (95CI 32, 37) for opioid-exposed (p < 0 .001). In the parsimonious pain and function models, opioid use, lower preoperative WOMAC score, depression, and obesity were associated with worse one-year pain and function. Patients prescribed preoperative opioids had worse WOMAC scores one-year after TKA respectively when compared to non-opioid users, after adjusting for other factors (opioid user pain score: −9.5, function score: −9.4, opioid exposed pain score: −2.6, function score: −3.6, p < 0 .001 for all). Further, opioid users with a concomitant diagnosis of depression had significantly worse one-year postoperative WOMAC scores when compared to non-depressed non-opioid users (scores −14, p < 0 .001 for both pain and function). In Alberta, 31% of patients were prescribed opioids within 180-days before TKA, preoperative opioid use was associated with worse one-year postoperative WOMAC pain and function scores relative to non-opioid users. Our results suggest that strategies to reduce preoperative opioid use could improve patient outcomes after TKA, and support the most recent Canadian opioid prescribing guidelines that attempt to minimize opioid use for chronic conditions such as arthritis.
Earlier studies dealing with trends in the management of osteonecrosis of the femoral head (ONFH) identified an increasing rate of total hip arthroplasties (THAs) and a decreasing rate of joint-preserving procedures between 1992 and 2008. In an effort to assess new trends in the management of this condition, this study evaluated the annual trends of joint-preserving versus arthroplasties for patients aged < or > 50 years old, and the incidence of specific operative management techniques. A total of 219,371 patients with ONFH were identified from a nationwide database between 1 January 2009 and 31 December 2015. The mean age was 54 years (18 to 90) and 105,298 (48%) were female. The diagnosis was made using International Classification of Disease, Ninth revision, Clinical Modification (ICD-9-CM) and Tenth Revision, Clinical Modification (ICD-10-CM) procedure codes. The percentage of patients managed using each procedure during each year was calculated and compared between years. The trends in the use of the types of procedure were also evaluated.Aims
Methods
To identify a suite of the key physical, emotional, and social outcomes to be employed in clinical practice and research concerning Perthes' disease in children. The study follows the guidelines of the COMET-Initiative (Core Outcome Measures in Effectiveness Trials). A systematic review of the literature was performed to identify a list of outcomes reported in previous studies, which was supplemented by a qualitative study exploring the experiences of families affected by Perthes’ disease. Collectively, these outcomes formed the basis of a Delphi survey (two rounds), where 18 patients with Perthes’ disease, 46 parents, and 36 orthopaedic surgeons rated each outcome for importance. The International Perthes Study Group (IPSG) (Dallas, Texas, USA (October 2018)) discussed outcomes that failed to reach any consensus (either ‘in’ or ‘out’) before a final consensus meeting with representatives of surgeons, patients, and parents.Aims
Methods
To compare long-term survival of all-cemented and hybrid total hip arthroplasty (THA) using the Exeter Universal stem. Details of 1,086 THAs performed between 1999 and 2005 using the Exeter stem and either a cemented (632) or uncemented acetabular component (454) were collected from local records and the New Zealand Joint Registry. A competing risks regression survival analysis was performed with death as the competing risk with adjustments made for age, sex, approach, and bearing.Aims
Methods
The aim of this study was to examine the recent trend in delivery of arthroscopic subacromial decompression (ASD) in Scotland and to determine if this varies by geographical location. Scottish Morbidity Records were reviewed retrospectively between March 2014 and April 2018 to identify records for every admission to each NHS hospital. The Office of Population Censuses and Surveys (OPCS-4) surgical codes were used to identify patients undergoing primary ASD. Patients who underwent acromioclavicular joint excision (ACJE) and rotator cuff repair (RCR) were identified and grouped separately. Procedure rates were age and sex standardized against the European standard population.Aims
Methods
Cementless Total Knee Arthroplasty has been developed to reduce the incidence of failure secondary to aseptic loosening, osteolysis and stress-induced osteopenia, especially in younger and more active patients. However, failures are still more common compared to cemented components, especially those involving the tibia. It is hypothesized that this is caused by incomplete contact between the tibial tray and the underlying bony surface due to: (i) inadequate flatness of the tibial osteotomy, or (ii) failure of implantation to spread the area of contact over the exposed cancellous surface. In the present study we compare the contact area developed during implantation of a cementless tray as a function of the initial flatness of the tibial osteotomy. Eight joint replacement surgeons prepared 14 cadaveric knees for cementless TKR using a standard instrumentation set (ZimmerBiomet Inc). The tibial osteotomy was created using an oscillating bone saw and a 1.27mm blade (Stryker Inc) directed by a slotted cutting guide mounted on an extramedullary rod and fixed to the tibia with pins and screws. The topography of the exposed cancellous surface was captured with a commercial laser scanner (Faro Inc, Halifax, approx. 33,000 surface points). 3D computer models of each tibial surface were generated in a CAD environment (Rapidform, Inuus). After scanning, a cementless tibial tray was implanted on the prepared tibial surface using a manual impactor. The tray-tibia constructs were dissected free of soft tissue, embedded in mounting resin, and sectioned with a diamond wafering saw. Points of bone-tray contact and interface separation were identified by stereomicroscopy and incorporated in the 3D computer models. Maps were generated depicting contacting and non-contacting areas Each model was subdivided into 7 zones for characterizing the distribution of interface contact in terms of anatomic location.Background
Method
Corrosion products from modular taper junctions are a potent source of adverse tissue reactions after THR. In an attempt to increase the area of contact and resistance to interface motion in the face of taper mismatches, neck trunnions are often fabricated with threaded surfaces designed to deform upon assembly. However, this may lead to incomplete contact and misalignment of the head on the trunnion, depending upon the geometry and composition of the mating components. In this study we characterized the effect of different femoral head materials on the strength and area of contact of modular taper constructs formed with TiAlV trunnions. Three groups of 36mm femoral heads (CoCr, Biolox ceramic; Oxinium) and matching Ti-6Al-4V rods with 12/14 trunnions were selected for use in this study. The surface of each trunnion was coated with a 20nm layer of gold applied by sputter-coating in vacuo. Each head/trunnion pair was placed in an alignment jig and assembled with a peak axial impaction force of 2000N using a drop tower apparatus. After assembly, each taper was disassembled in a custom apparatus mounted in a mechanical testing machine (Bionix. MTS. After separation of the components, the surface of each trunnion was examined with backscattered electron microscopy to reveal the area of disruption of the original gold-coated surface. Images encompassing the entire surface of the trunnion were collected and quantified by image processing.Introduction
Materials and Methods
In total hip arthroplasty, correct sizing is critical for fixation and longevity of cementless components. Previously, three-dimensional CT templating has been shown to be more accurate than using 2D radiographs. The accuracy of the Optimized Positioning System (OPSTM) planning software has not been reported. The aim of this study was to measure the accuracy of the OPS planning software in predicting the implanted acetabular cup and femoral stem size when used with the direct anterior approach. Between October 2018 and March 2019, 95 patients received a bone preserving cementless MiniHip stem (Corin, UK). Sixty-three of these patients also received a cementless Trinity cup (Corin, UK). All patients were sent for OPSTM pre-operative planning, a patient-specific dynamic modelling software used to determine the optimal acetabular and femoral component size and positions. Average age was 57 (28 to 78) and 44% were female. All cases were performed using the direct anterior approach. The sizes of implants used were retrospectively compared to the planned OPSTM sizes.Introduction
Method
In theory, Finite Element Analysis (FEA) is an attractive method for elucidating the mechanics of modular implant junctions, including variations in materials, designs, and modes of loading. However, the credence of any computational model can only be established through validation using experimental data. In this study we examine the validity of such a simulation validated by comparing values of interface motion predicted using FEA with values measured during experimental simulation of stair-climbing. Two finite element models (FEM) of a modular implant assembly were created for use in this study, consisting of a 36mm CoCr femoral head attached to a TiAlV rod with a 14/12 trunnion. Two head materials were modelled: CoCr alloy (118,706 10-noded tetrahedral elements), and alumina ceramic (124,710 10-noded tetrahedral elements). The quasi-static coefficients of friction (µs) of the CoCr-TiAlV and Ceramic-TiAlV interfaces were calculated from uniaxial assembly (2000N) and dis-assembly experiments performed in a mechanical testing machine (Bionix, MTS). Interface displacements during taper assembly and disassembly were measured using digital image correlation (DIC; Dantec Dynamics). The assembly process was also simulated using the computational model with the friction coefficient set to µs and solved using the Siemens Nastran NX 11.0 Solver. The frictional conditions were then varied iteratively to find the value of µ providing the closest estimate to the experimental value of head displacement during assembly. To validate the FEA model, the relative motion between the head and the trunnion was measured during dynamic loading simulating stair-climbing. Each modular junction was assembled in a drop tower apparatus and then cyclically loaded from 230–4300N at 1 Hz for a total of 2,000 cycles. The applied load was oriented at 25° to the trunnion axis in the frontal plane and 10° in the sagittal plane. The displacement of the head relative to the trunnion during cyclic loading was measured by a three-camera digital image correlation (DIC) system. The same loading conditions were simulated using the FEA model using the optimal value of µ derived from the initial head assembly trials.INTRODUCTION
MATERIALS and METHODS
We report on the 5 year results of a randomized study comparing TKR performed using conventional instrumentation versus electromagnetic computer-assisted surgery. This study analysed patient reported outcome measures (PROMs) at 5 years utilising the American Knee Society Score (AKSS), Oxford Knee Score (OKS), the Short Form 36 score and range of motion (ROM). Of the 200 patients enrolled 125 completed 5 year follow up, 62 in the navigated group and 63 in the conventional group. There were 28 deceased patients, 29 withdrawals and 16 lost to follow-up. There was improvement in clinical function in most PROMs from 1-5 year follow up across both groups. OKS improved from a mean of 26.6 (12–55) to 35.1 (5–48). AKSS increased from 75.3 (0–100) to 78.4 (−10–100), SF36 from 58.9 (2.5–100) to 53.2 (0–100). ROM improved by an average 7 degrees from 110 degrees to 117 degrees (80–135). There was no statistically significant difference in PROMs between the groups at 5 years. Patients undergoing revision surgery were identified from the dataset and global PACS. There were no revisions within 5 years in the navigated group and 3 revisions in the conventional group, two for infection and one for mid-flexion instability, giving an all cause revision rate of 3.06% at 5 years for this group. There appears to be no significant advantage in clinical function for patients undergoing TKR for OA of the knee with electromagnetic navigation when compared to conventional techniques. There may be an advantage in reducing early revision rates using this technology.
MOXIMED KineSpring® Knee Implant System is an Orthopaedic device designed for younger or highly active patients with osteoarthritis. The device is placed under the skin, is attached to the tibia and femur, and contains springs which help limit some of the forces that are transmitted through the knee during activities such as walking or running and thereby relieve pain that may be experienced by patients with early arthritis of the knee. The aim of this study is to determine the long term safety and efficacy of the KineSpring knee implant system. This is a prospective case series involving two centres in Glasgow. 29 patients (mean age of 45.1 years and range 18-65 years) were recruited into the study between 2011 and 2016. The Primary outcome measure was Oxford knee score (OKS) at 2, 5 and 10 years post-operatively. Secondary outcome measures include device related complications and survival, patient reported functional outcome measures, patient satisfaction, pain levels and change in radiographic classification of osteoarthritis At 2-year follow-up, 7 implants were removed (74.1% survival). Complications include deep infection, requiring removal in 1 patient, 2 implant failures requiring removal and one spring breakage. In comparison to pre-operative measures there was an improvement in the pain (3.58 vs. 5.20, p=0.02), stiffness (4.16 vs. 4.47, p=0.6) and OKS (32.4 vs. 36.9, p=0.03). The KineSpring improves overall pain, stiffness and functional outcome at 2 years following surgery, however there was a high rate of removal and further long-term follow up analysis is required regarding its effectiveness.
3D preoperative planning software for anatomic and reverse total shoulder arthroplasty (ATSA and RTSA) provides additional insight for surgeons regarding implant selection and placement. Interestingly, the advent of such software has brought previously unconsidered questions to light on the optimal way to plan a case. In this study, a survey of shoulder specialists from the American Shoulder and Elbow Society (ASES) was conducted to examine thought patterns in current glenoid implant selection and placement. 172 ASES members completed an 18-question survey on their thought process for how they select and place a glenoid implant for both ATSA and RTSA procedures. Data was collected using a custom online Survey Monkey survey. Surgeon answers were split into three cohorts based on their responses to usage of 3D preoperative planning software: high users, seldom users, and non-users. Data was analyzed for each cohort to examine differences in thought patterns, implant selection, and implant placement.INTRODUCTION
METHODS
The advent of CT based 3D preoperative planning software for reverse total shoulder arthroplasty (RTSA) provides surgeons with more data than ever before to prepare for a case. Interestingly, as the usage of such software has increased, further questions have appeared over the optimal way to plan and place a glenoid implant for RTSA. In this study, a survey of shoulder specialists from the American Shoulder and Elbow Society (ASES) was conducted to examine thought patterns in current RTSA implant selection and placement. 172 ASES members completed an 18-question survey on their thought process for how they select and place a RTSA glenoid implant. Data was collected using a custom online Survey Monkey survey. Surgeon answers were split into two cohorts based on number of arthroplasties performed per year: between 0–75 was considered low volume (LV), and between 75–200+ was considered high volume (HV). Data was analyzed for each cohort to examine differences in thought patterns, implant selection, and implant placement.INTRODUCTION
METHODS
Combined glenoid and humeral bone loss has been identified as an important factor in predicting recurrence after arthroscopic shoulder stabilisation. The “glenoid track” concept is proposed to predict recurrent instability by comparing the relative size of the glenoid to the humeral bone defect. The aim of this study was to investigate whether assessment of the glenoid track on a pre-operative MR arthrogram could be used to predict subsequent instability in a typical UK population. A retrospective study was undertaken of 175 primary arthroscopic stabilisation procedures of which 82% (n=143) were men. The median age was 26 years (IQR 22 to 32, range 16 to 77). The median follow-up was 76 months (range 21 to 125). A pre-operative MR arthrogram was used to determine if the shoulder was on-track or off-track. The endpoint of recurrent dislocation was examined. The prevalence of “off-track” bone loss in this group was 14.2% (n=25). There were 6 (24%) dislocations in the off-track group compared with 5 (3.33%) dislocations in the on-track group (RR 7.2, 95% CI 2.45 to 20.5, p=0.001). At 5 years, the cumulative redislocation rate was 26.1% in the off-track group compared with 8.7% in on-track group. The rate of any recurrent instability was 60% (n=15) v 18% (n=27) (RR 3.33, 95% CI 2.02 to 5.20, p<0.0001). Glenoid track (on v off) was not predicted by gender (p=0.411). In a typical UK population assessment of the glenoid track on an MR arthrogram can be used to risk stratify patients with shoulder instability.
3D preoperative planning software for anatomic total shoulder arthroplasty (ATSA) provides surgeons with increased ability to visualize complex joint relationships and deformities. Interestingly, the advent of such software has seemed to create less of a consensus on the optimal way to plan an ATSA rather than more. In this study, a survey of shoulder specialists from the American Shoulder and Elbow Society (ASES) was conducted to examine thought patterns in current ATSA implant selection and placement. 172 ASES members completed an 18-question survey on their thought process for how they select and place an ATSA glenoid implant. Data was collected using a custom online Survey Monkey survey. Surgeon answers were split into two cohorts based on number of arthroplasties performed per year: between 0–75 was considered low volume (LV), and between 75–200+ was considered high volume (HV). Data was analyzed for each cohort to examine differences in thought patterns, implant selection, and implant placement.INTRODUCTION
METHODS
The objective of this study was to compare differences in alignment following robotic arm-assisted bi-unicompartmental knee arthroplasty (Bi-UKA) and conventional total knee arthroplasty (TKA). This was a prospective, randomised controlled trial of 70 patients. 39 TKAs were implanted manually, as per standard protocol at our institution, and 31 Bi-UKA patients simultaneously received fixed-bearing medial and lateral UKAs, implanted using robotic arm-assistance. Preoperative and 3-month postoperative CT scans were analysed to determine hip knee ankle angle (HKAA), medial distal femoral angle (MDFA), and medial proximal tibial angle (MPTA). Analysis was repeated for 10 patients by a second rater to validate measurement reliability by calculating the intra-class correlation coefficient (ICC). Mean change in HKAA towards neutral was 2.7° in TKA patients and 2.3° in Bi-UKA patients (P=0.6). Mean change in MDFA was 2.5° for TKA and 1.0° for Bi-UKA (P<0.01). Mean change in MPTA was 3.7° for TKA and 0.8° for Bi-UKA (P<0.01). Mean postoperative MDFA and MPTA for TKAs were 89.8° and 89.6° respectively, indicating orientation of femoral and tibial components perpendicular to the mechanical axis. Mean postoperative MDFA and MPTA for Bi-UKAs were 91.0° and 86.9° respectively, indicating a more oblique joint line orientation. Inter-rater agreement was excellent (ICC>0.99). Early functional activities, according to the new Knee Society Scoring System, favoured Bi-UKAs (P<0.05). Robotic arm-assisted, cruciate-sparing Bi-UKA better maintains the natural anatomy of the knee in the coronal plane and may therefore preserve normal joint kinematics, compared to a mechanically aligned TKA. This has been achieved without significantly altering overall HKAA.
It is unknown whether kinematic alignment (KA) objectively improves knee balance in total knee arthroplasty (TKA), despite this being the biomechanical rationale for its use. This study aimed to determine whether restoring the constitutional alignment using a restrictive KA protocol resulted in better quantitative knee balance than mechanical alignment (MA). We conducted a randomized superiority trial comparing patients undergoing TKA assigned to KA within a restrictive safe zone or MA. Optimal knee balance was defined as an intercompartmental pressure difference (ICPD) of 15 psi or less using a pressure sensor. The primary endpoint was the mean intraoperative ICPD at 10° of flexion prior to knee balancing. Secondary outcomes included balance at 45° and 90°, requirements for balancing procedures, and presence of tibiofemoral lift-off.Aims
Methods
This annotation briefly reviews the history of artificial intelligence and machine learning in health care and orthopaedics, and considers the role it will have in the future, particularly with reference to statistical analyses involving large datasets. Cite this article:
The EU-funded Back-UP project aims to develop a cloud computer platform to guide the treatment of low back and neck pain (LBNP) in first contact care and early rehabilitation. In order to identify evidence-based treatment options that can be recommended and are accessible to people with LBNP across Europe, we conducted a systematic review of recently published guidelines. Electronic databases, including Medline, Embase, CINAHL, PsycINFO, HMIC, Epistemonikos, PEDro, TRIP, NICE, SIGN, WHO, Guidelines International Network (G-I-N) and DynaMed Plus were searched. We searched for guidelines published by European health professional or guideline development organisations since 2013, focusing on the primary care management of adult patients presenting with back or neck pain (including whiplash associated symptoms, radicular pain, and pregnancy-related LBP). The AGREE-II tool was used to assess the quality of guideline development and reporting.Background and aims
Methods
The purpose of this study was to analyze trends in the surgical management of ON in recent years. Specifically, we evaluated the annual prevalences of: 1) joint preserving procedures (osteotomies and core decompression/grafts) and 2) joint non-preserving procedures (total hip arthroplasties [THAs], revision THAs, partial THAs) for the treatment of osteonecrosis of the femoral head (ONFH) between 2009 and 2016. A total of 406,239 ONFH patients who were treated between 2009 and 2016 were identified from a nationwide database. Treatment procedures were extracted using ICD-9-CM and ICD-10-CM procedure codes. Annual rates of each of the above procedures were calculated and the trends in the procedure types were also evaluated. Chi-square tests were performed to compare the annual prevalence of each procedure. The mean annual prevalence over the 8-year study period was calculated for each procedure.Introduction
Background
Patients with hip abductor tendon tears amenable to endoscopic repair tend to be severely disabled and older. However, low preop baseline patient reported outcome (PRO) and advancing age are each often reported to be a harbinger of poor result with hip arthroscopy. Thus, the purpose of this study is to report the demographic makeup of this population and how these patients faired in terms of preop scores and reaching both Minimal Clinically Important Difference (MCID) and Substantial Clinical Benefit (SCB). Sixty-six consecutive hips in 64 patients (2 bilateral) undergoing endoscopic abductor tendon repair with a hollow core bioabsorbable suture anchor and having achieved two-year follow-up were prospectively assessed with modified Harris Hip Score (mHHS) and international Hip Outcome Tool (iHOT) scores. The MCID for patients undergoing hip arthroscopy has previously been determined as 8 for the mHHS and 13 for the iHOT. SCB has been determined as 20 for the mHHS and 28 for the iHOT. Subgroups were compared using the independent samples t-test.Introduction
Methods
Lower back pain (LBP) is one of the ten leading causes of disease burden globally, producing significant detrimental effects on physical and emotional wellbeing whilst having a substantial economic burden for society. There is an inverse relationship between socio-economic status and pain prevalence. The effectiveness of a locally run ‘Back to Fitness Programme’ (6-week education and exercise programme) in the most deprived local authority area in England was evaluated. Patients at Blackpool Hospitals NHS Trust over a 6-month timeframe were included. Initial data were collected from 49 patients (mean age 53.4 years, 67% female). The amount of final data collected varied per outcome measure due to a range of factors. Participants reported the programme had helped with their understanding of pain (n=16, 100%), ability to move around and function (n=15, 94%), and level of pain (n=14, 88%). Looking at Roland Morris Disability Questionnaire scores (n=17), 88% (n=15) of patients indicated a reduction (n=12, 71%) or no change (n=3, 18%) in perceived disability. The Pain Self Efficacy Questionnaire (n=18) showed that 78% (n=14) of participants perceived an increase in their average level of confidence to move despite pain. There was an overall improvement in understanding of pain reflected by Revised Neurophysiology of Pain Questionnaire scores (n=44): 89% (n=39) improved (n=36, 82%) or did not change (n=3, 7%). Regarding lumbar flexion post-programme (n=17), 77% (n=13) of participants demonstrated an improvement (n=9, 53%) or no change (n=4, 24%).A statement of the purposes of the study and background
A summary of the methods used and the results
The behavioural change wheel methodology and social cognitive theory were combined to inform and develop a rehabilitation programme following lumbar fusion surgery (REFS). This qualitative study evaluated participant's experiences of lumbar fusion surgery, including REFS, to identify valued programme content (‘active ingredients’). A feasibility-RCT suggested REFS achieved a meaningful impact in disability and pain self-efficacy compared to ‘usual care’ (p=0.014, p=0.007). In keeping with MRC guidance a qualitative evaluation was undertaken to understand possible mechanisms of action.Purpose
Background
Custom flange acetabular components (CFACs) are a patient-specific option for addressing large acetabular defects at revision total hip arthroplasty (THA), but patient and implant characteristics that affect survivorship remain unknown. This study aimed to identify patient and design factors related to survivorship. A retrospective review of 91 patients who underwent revision THA using 96 CFACs was undertaken, comparing features between radiologically failed and successful cases. Patient characteristics (demographic, clinical, and radiological) and implant features (design characteristics and intraoperative features) were collected. There were 74 women and 22 men; their mean age was 62 years (31 to 85). The mean follow-up was 24.9 months (Aims
Patients and Methods
In a recent study, 54.5% of patients reporting to arthroplasty clinics in the US were obese. We performed a recent literature review to determine how obesity impacts outcomes in total hip and knee arthroplasty and what must be done to improve outcomes in the obese arthroplasty patient. Specifically, obese patients have shown increased rates of infection, dislocation, need for revision, wound dehiscence, increased operative time and prolonged hospital stay. Additionally, obese TKA patients have been shown to have increased rates of aseptic loosening, thromboembolic events, wound complications, and cardiopulmonary events. Worsening severity of obesity seems to correlate with worsening outcomes and super obesity (BMI>50) has been identified as an independent risk factor for complications. Patients with BMI>35 have shown to be 6.7 times more likely to develop infection after TKA. Patients with BMI>40 have a 3.35 times higher rate of revision for deep infection than those with BMI<35. The odds ratio for major complications increases dramatically beyond BMI>45. How can we improve outcomes in the obese patient? Preoperative care for the obese patient involves nutritional counseling, incorporating weight loss methods, physical therapy, metabolic workup and diagnosis and management of frequent comorbid conditions (OSA, DM2, HTN, HLD, malnutrition, renal failure). Identifying and managing comorbidities is especially important given that some comorbidities such as malnutrition have been shown to be as strong or even stronger an independent risk factor for postoperative TJA complications than obesity. In some cases higher complications were seen which some authors attribute to bariatric patients remaining in a catabolic state after weight loss. We know that obesity and its associated comorbid conditions do have worse outcomes and increased complications in TJA patients. We also know that complications proportionately increase with increasing severity of obesity. The super-obese population is at the greatest risk of complication following TJA and preoperative screening and management is essential in reducing complications. Although weight loss is important, bariatric data has shown that it does not solve the problem of obesity in itself and the patient's metabolic state is likely a more important issue. Implant selection is important and strong consideration should be given to avoiding direct anterior approach in the THA obese patient. Understanding of obesity specific complications and treatment options is crucial for patient counseling and optimization to ensure successful treatment in obese TJA patients.
Revision total hip arthroplasty (THA) is a challenging scenario following complex primary THA for developmental dysplasia of hip (DDH). This study envisages the long-term outcomes of revision DDH and the role of lateral structural support in socket fixation in these young patients who may require multiple revisions in their life-time. Hundred and eighteen consecutive cemented revision THAs with minimum follow up of 5 years following primary diagnosis of DDH operated by a single unit between January 1974 and December 2012 were analysed for their clinical and radiological outcomes.Background
Materials and methods
The development of more wear resistant biomaterials and better locking mechanisms for the polyethylene into the tibial base has significantly reduced polyethylene wear as a reason for revision TKA. Aseptic loosening is now the primary cause for revision TKA. Loosening can be caused by multifactorial operative issues: 1] patient selection, 2] implant alignment, 3] cementing technique. Furthermore, aseptic loosening occurs at a consistent rate over time. Increased cement penetration is important to counter bone resorption. Increasing penetration also improves cement mantle toughness leading to better mechanical integrity of the bone-cement interface and reduces bone-cement interface stress. It is important to recognise that a cleaner and drier interface does improve bone-cement penetration. Techniques to improve the process include better cement formulations, drilling sclerotic bone, devices and implant features to increase pressurization, using negative pressure suction ports in the tibia. We have extensive experience with CarboJet, a method of CO2 gas jet cleaning and drying. This experience was developed during 20 years of performing TKA with NO tourniquet. Schnetler et al found that the “use of a tourniquet in TKA causes a paradoxical increase in total blood loss”. So, NO tourniquet TKA is becoming the new paradigm for knee arthroplasty in reconstructive orthopaedics. Goldstein reported that pressurised carbon dioxide jet lavage resulted in a 35% increase in cement penetration depth when used vs. use of pulsatile saline lavage alone. Meneghini used this pressurised carbon dioxide system to study the influence of NO tourniquet use in TKA. He found a significant lowering of opioid consumption postoperatively. Another important factor in increasing the cement interdigitation is the influence of lipids which significantly weakens the bond at the interfaces. If motion is allowed during cementation there is additional loss of penetration and therefore fixation. The pressurised carbon dioxide delivered by the CarboJet system actually pushes the lipid, fatty marrow up and out of the bone allowing it to be suctioned or lap dried from the interface surface. The NO tourniquet technique and the use of carbon dioxide jet gas delivery to improve the bone-cement interface in TKA will be demonstrated.
In total knee arthroplasty, the aim is to relieve pain and provide a stable, functional knee. Sagittal stability is crucial in enabling a patient to return to functional activities. Knee implants with a medial pivot (MP) design are thought to more accurately reproduce the mechanics of the native joint, and potentially confer greater antero-posterior stability through the range of flexion than some other implant designs. This study aims to compare the sagittal stability of four different total knee arthroplasty implant designs. Method Comparison was made between four different implant designs: medial pivot (MP), two different types of cruciate retaining (CR1 and CR 2) and deep dish (DD). A cohort of 30 Medial Pivot (MP) knees were compared with matched patients from each of the other designs, 10 in each group. Patients were matched for age, body mass index and time to follow up. Clinical examination was carried out by an orthopaedic surgeon blinded to implant type, and sagittal stability was tested using a KT1000 knee arthrometer, applying 67N of force at 30˚ and 90˚.Introduction
Aim
There is great potential for the use of computational tools within the design and test cycle for joint replacement devices. The increasing need for stratified treatments that are more relevant to specific patients, and implant testing under more realistic, less idealised, conditions, will progressively increase the pre-clinical experimental testing work load. If the outcomes of experimental tests can be predicted using low cost computational tools, then these tools can be embedded early in the design cycle, e.g. benchmarking various design concepts, optimising component geometrical features and virtually predicting factors affecting the implant performance. Rapid, predictive tools could also allow population-stratified scenario testing at an early design stage, resulting in devices which are better suited to a patient-specific approach to treatment. The aim of the current study was to demonstrate the ability of a rapid computational analysis tool to predict the behaviour of a total hip replacement (THR) device, specifically the risk of edge loading due to separation under experimental conditions. A series of models of a 36mm BIOLOX® Delta THR bearing (DePuy Synthes, Leeds, UK) were generated to match an experimental simulator study which included a mediolateral spring to cause lateral head separation due to a simulated mediolateral component misalignment of 4mm. A static, rigid, frictionless model was implemented in Python (PyEL, runtime: ∼1m), and results were compared against 1) a critically damped dynamic, rigid, FE model (runtime: ∼10h), 2) a critically damped dynamic, rigid, FE model with friction (µ = 0.05) (runtime: ∼10h), and 3) kinematic experimental test data from a hip simulator (ProSim EM13) under matching settings (runtime: ∼6h). Outputs recorded were the variation of mediolateral separation and force with time.INTRODUCTION
METHODS
Component positioning is of great importance in total hip arthroplasty (THA) and navigation systems can help guide surgeons in the optimal placement of the implants. We report on a newly developed navigation system which employs an inertial measurement unit (IMU) to measure acetabular cup inclination and anteversion. To assess the accuracy of the IMU when used for acetabular cup placement and compare this with an established optical navigation system (ONS).Introduction
Aims
Variability in placement of total shoulder arthroplasty (TSA) glenoid implants has led to the increased use of 3D CT preoperative planning software. Computer assisted surgery (CAS) offers the potential of improved accuracy in TSA while following a preoperative plan, as well as the flexibility for intraoperative adjustment during the procedure. This study compares the accuracy of implantation of reverse total shoulder arthroplasty (rTSA) glenoid implants using a CAS TSA system verses traditional non-navigated techniques in 30 cadaveric shoulders relative to a preoperative plan from 3D CT software. High resolution 1mm slice thickness CT scans were obtained on 30 cadaveric shoulders from 15 matched pair specimens. Each scan was segmented and the digital models were incorporated into a preoperative planning software. Five fellowship trained orthopedic shoulder specialists used this software to virtually place a rTSA glenoid implant as they deemed best fit in six cadavers each. The specimens were randomized with respect to side and split into a cohort utilizing the CAS system and a cohort utilizing conventional instrumentation, for a total of three shoulders per cohort per surgeon. A BaSO4 PEEK surrogate implant identical in geometry to the metal implant used in the preoperative plan was used in every specimen, to maintain high CT resolution while minimizing CT artifact. The surgeons were instructed to implant the rTSA implants as close to their preoperative plans as possible for both cohorts. In the CAS cohort, each surgeon used the system to register the native cadaveric bones to each respective CT, perform the TSA procedure, and implant the surrogate rTSA implant. The surgeons then performed the TSA procedure on the opposing side of the matched pair using conventional instrumentation. Postoperatively, CT scans were repeated on each specimen and segmented to extract the digital models. The pre- and postoperative scapulae models were aligned using a best fit match algorithm, and variance between the virtual planned position of the implant and the executed surgical position of the implant was calculated [Fig 1].INTRODUCTION
METHODS
Over the last decade, sensor technology has proven its benefits in total knee arthroplasty, allowing the quantitative assessment of tension in the medial and lateral compartment of the tibiofemoral joint through the range of motion (VERASENSE, OrthoSensor Inc, FL, USA). In reversal total shoulder arthroplasty, it is well understood that stability is primarily controlled by the active and passive structures surrounding the articulating surfaces. At current, assessing the tension in these stabilizing structures remains however highly subjective and relies on the surgeons’ feel and experience. In an attempt to quantify this feel and address instability as a dominant cause for revision surgery, this paper introduces an intra-articular load sensor for reverse total shoulder arthroplasty (RTSA). Using the capacitive load sensing technology embedded in instrumented tibial trays, a wireless, instrumented humeral trial has been developed. The wireless communication enables real-time display of the three-dimensional load vector and load magnitude in the glenohumeral joint during component trialing in RTSA. In an in-vitro setting, this sensor was used in two reverse total shoulder arthroplasties. The resulting load vectors were captured through the range of motion while the joint was artificially tightened by adding shims to the humeral tray.Introduction & Aims
Method
Preoperative planning software for anatomic total shoulder arthroplasty (ATSA) allows surgeons to virtually perform a reconstruction based off 3D models generated from CT scans of the glenohumeral joint. The purpose of this study was to examine the distribution of chosen glenoid implant as a function of glenoid wear severity, and to evaluate the inter-surgeon variability of optimal glenoid component placement in ATSA. CT scans from 45 patients with glenohumeral arthritis were planned by 8 fellowship trained shoulder arthroplasty specialists using a 3D preoperative planning software, planning each case for optimal implant selection and placement. The software provided three implant types: a standard non-augmented glenoid component, and an 8° and 16° posterior augment wedge glenoid component. The software interface allowed the surgeons to control version, inclination, rotation, depth, anterior- posterior and superior-inferior position of the glenoid components in 1mm and 1° increments, which were recorded and compared for final implant position in each case.INTRODUCTION
METHODS
Preoperative planning software for reverse total shoulder arthroplasty (RTSA) allows surgeons to virtually perform a reconstruction based off 3D models generated from CT scans of the glenohumeral joint. While anatomical studies have defined the range of normal values for glenoid version and inclination, there is no clear consensus on glenoid component selection and position for RTSA. The purpose of this study was to examine the distribution of chosen glenoid implant as a function of glenoid wear severity, and to evaluate the inter-surgeon variability of optimal glenoid component placement in RTSA. CT scans from 45 patients with glenohumeral arthritis were planned by 8 fellowship trained shoulder arthroplasty specialists using a 3D preoperative planning software, planning each case for optimal implant selection and placement. The software provided four glenoid baseplate implant types: a standard non-augmented component, an 8° posterior augment wedged component, a 10° superior augment wedged component, and a combined 8° posterior and 10° superior wedged augment component. The software interface allowed the surgeons to control version, inclination, rotation, depth, anterior-posterior and superior-inferior position of the glenoid components in 1mm and 1° increments, which were recorded and compared for final implant position in each case.INTRODUCTION
METHODS
