Aims

Appropriate acetabular component placement has been proposed for prevention of postoperative dislocation in total hip arthroplasty (THA). Manual placements often cause outliers in spite of attempts to insert the component within the intended safe zone; therefore, some surgeons routinely evaluate intraoperative pelvic radiographs to exclude excessive acetabular component malposition. However, their evaluation is often ambiguous in case of the tilted or rotated pelvic position. The purpose of this study was to develop the computational analysis to digitalize the acetabular component orientation regardless of the pelvic tilt or rotation.

Summary Statement

The incidence of osteonecrosis was significantly lower in the anti-vasospasm agent group (32%) than that in the control group (75%). Vasospasm is one of the important factors involved in the pathogenesis of steroid-induced osteonecrosis.

Introduction

Transtrochanteric curved varus osteotomy is one of the effective joint-preserving operations for osteonecrosis (ON) of the femoral head. We correlated various factors with the radiological outcome of this procedure.

Introduction

The objective of this study was to verify the long-term outcome of transtrochanteric anterior rotational osteotomy (ARO) for osteonecrosis of the femoral head (ONFH) in young patients with systemic lupus erythematosus (SLE).

Introduction

Subchondral insufficiency fracture of the femoral head (SIF) is a recently proposed concept. It is generally seen in elderly people, however, some young adults have also been reported to suffer from this fracture. The purpose of this study was to investigate the clinical results of a transtrochanteric anterior rotational osteotomy (ARO) performed in young adults with SIF.

Introduction

Subchondral insufficiency fracture of the femoral head (SIF) often occurs in osteoporotic elderly patients. Patients usually suffer from acute hip pain without any obvious antecedent trauma. Radiologically, a subchondral fracture is seen mainly in the superolateral portion of the femoral head. The T1-weighted magnetic resonance (MR) images show a low-intensity band in the subchondral area of the femoral head, which tends to be irregular, disconnected, and convex to the articular surface. This low-intensity band in SIF was histologically proven to correspond to the fracture line with associated repair tissue. Some cases of SIF resolve after conservative treatment, while others progress until collapse, thereby requiring surgical treatment. The prognosis of SIF remains unclear. This study investigated the risk factors that influence the prognosis of SIF based on the progression of the collapse.

Introduction

Subchondral insufficiency fracture (SIF) needs to be differentiated from osteonecrosis. The purpose of this study was to evaluate the imaging and histopathological findings of patients 60 years or older with radiological evidence of subchondral collapse of the femoral head.

Background

In Japan, idiopathic osteonecrosis of the femoral head (ONFH) is designated as a specified rare and intractable disease in patients for whom medical care is subsidized through the Specified Disease Treatment Research Program. Each patient is approved for the subsidy based upon a prefectural governmental review after filing an application together with a clinical research form documenting the patient's medical history, laboratory/clinical findings, and treatment. The purpose of this study was to conduct a fact-finding study of ONFH patients in the Fukuoka Prefecture based on clinical research forms of the Specified Disease Treatment Research Program.

Transposition osteotomy of the acetabulum (TOA) was the first periacetabular osteotomy for the osteoarthritis hips due to acetabular dysplasia, in which the acetabulum was transposed with articular cartilage. TOA improves coverage of the femoral head to restore congruity and stability, and also prevent further osteoarthritis deterioration and induce regeneration of the joint. Many good clinical outcomes have been reported for such periacetabular osteotomies for osteoarthritis of the hips at an early stage. In contrast, the clinical outcome is controversial for those hips at an advanced stage, in which the joint space has partly disappeared. The purpose of this study was to investigate whether TOA is an appropriate option for treatment of osteoarthritis of the hips at the advanced stage by comparing with matched control hips at the early stage.

Between 1998 and 2001, TOA was performed in 104 hips of 98 patients.

Sixteen of 17 hips (94%) with osteoarthritis at the advanced stage were examined and compared with 37 matched control hips at the early stage. The mean age at the operation was 48(38–56) and the mean follow-up period was 88 (65–107) months. TOA corrected the acetabular dysplasia and significantly improved containment of the femoral head.

No hips had secondary operations including THA. Clinical scores were also significantly improved in both of the groups. In the advanced osteoarthritis cases, there was a tendency for abduction congruity before transposition osteotomy of the acetabulum to reflect the clinical outcome.

TOA is a promising treatment option for the advanced osteoarthritis of the hips as well as for those patients at the early stage when preoperative radiographs show good congruity or containment of the joint.

Combined anteversion (CA) is defined as the sum of the anteversions of acetabular and femoral components. In this study, we determined the appropriate CA in a variety of femoral versions using a total hip arthroplasty model. In addition, we also examined the usefulness of a changeable neck to improve range of hip motion in these cases.

Using a THA model, the range of motion (ROM) was tested in various CA values obtained by changing the anteversion of a cup in six increments after setting the femoral anteversion to 20° or 60° anteversion and 20° retroversion. The angle of the changeable neck was changed in 11 increments of 5°. To evaluate stability, the range of internal rotation at 90° flexion, the external rotation at 0° extension, and the range flexion was measured when any impingement occurred prior to dislocation. We defined the required ROM that met 40° internal rotation, 30° external rotation, and 110° flexion.

In normal 20° anteversion group, the required ROM was achieved with CA between 30° and 50° without using any changeable necks. In excessive anteversion 60° group, the range of external rotation was less than 10° even when the acetabular component was set 10° retroverted, because of the bone impingement between the greater trochanter and the posterior acetabulum. When 25° retroverted changeable neck was used, ROM improved to 30° external rotation and satisfied the required ROM. In 20° retroversion group, the internal rotation angle was 31° even when the acetabular component was opened 35° anteverted, because of anterior neck-liner impingement. When 25° anteverted changeable neck was used, ROM improved to 39° internal rotation and 130° flexion.

In cases with normal anteversions, the required ROM can be achived by adjusting CA. In cases with excessive anteversion or retroversion, there was a limitation of the CA adjustment. The use of changeable necks allows for further improvement of ROM by compensating femoral anteversions.

Treating Crowe type 3 or 4 of hips tends to be technically difficult when performing total hip arthroplasty (THA) due to the severely dysplastic acetabulum and proximal femur in addition to a high dislocation of the hip. Since the socket is limited to being placed at the original hip center, a femoral shortening osteotomy is often required in order to prevent neurovascular problems. This osteotomy will need the stability of the femoral stem with both the proximal and the distal femoral bones. We used the modular S-ROM stem, which has a valuable proximal structure and a distal flute structure to stabilize the stem with the proximal and distal femoral fragments. The purpose of this study was to report the clinical and radiographic results of the primary THA with a shortening osteotomy while also using the S-ROM prosthesis.

Between 1994 and 2004, primary THA using the S-ROM prosthesis was performed on 7 hips in 6 cases (1 male, 5 females). Crowe type 3 or 4 was observed in one and 6 hips, respectively. The mean age at operation was 56 years old (range 51~60). The mean follow-up period was 41 months (range 24~56 months). Four hips had previously undergone a subtrochanteric valgus osteotomy. All hips underwent a step-cut femoral osteotomy at the proximal metaphysis for the shortening and/or correction of angulations with on-lay chip bone grafts. All of the used stems were straight type. The clinical outcome was evaluated using the clinical scoring system of hip joints established by the Japanese Orthopaedic Association (JOA). According to a 100 point scale, pain was determined to be 40, ROM was 20, gait was 20 and ADL was 20.

No hips had undergone any revision surgery as of the most recent follow-up. Union was achieved at the osteotomy site in all hips. Neither osteolysis nor a loosening of the implant was radiographically observed. The mean JOA score before THA and at the last follow-up was 41 (31–48) and 81 (62–91) points, respectively. The mean postoperative days to start full weight bearing was 53 days (range 49~70). In two cases (28%), a procedure using circular wiring was performed to treat a crack in the proximal femur.

The S-ROM prosthesis was thus found to be useful for primary THA with a shortening metaphyseal femoral osteotomy for hips in patients with Crowe type 3 or 4 developmental dysplasia.

It is recommended in the TKA operation to balance the tension of soft tissues to make the rectangular gap in both flexion and extension because significant imbalance may result in eccentric stress on the polyethylene insert. However, no intensive research has been done on the medial and lateral laxity of the normal knee

X-ray of 50 normal knees were taken under the varus or valgus stress in both extension and flexion at 80 degrees. The angle of lines on the femoral condyles and tibia plateau was measured. The same methods were also done for the 20 osteoarthritis knees.

In extension of the normal knees, the mean angle was 5.06 degrees in varus stress and was 2.46 degrees in valgus stress. In flexion of the normal knees, the mean angle was 5.04 degrees in varus stress and was 1.82 degrees in valgus stress. Therefore, the lateral laxity was significantly larger than the medial laxity in both extension and flexion (p< 0.0001). The lateral laxity was significantly larger also in osteoarthritis knees (p< 0.0001).

There are some arguments about the priority to make the perfect rectangular gaps. The methods to measure the tension of soft tissues during the operation are not accurate and does not always reflect the post-operative tensions. Furthermore, the tension during the operation may be different from dynamic phase such as walking and standing. The present study showed that the mediolateral laxity was asymmetrical in the normal knees. This imbalance may be necessary for the medial pivot movement of the normal knee. These results suggest that a slight lateral laxity is acceptable during TKA operation and may be beneficial to achieve the normal kinematics especially for the cruciate retaining prosthesis.

Polyethylene wear in total knee arthroplasty (TKA) is a complex and mutifactorial process. It is generally recognized that wear is directly related to a material wear factor, contact stress, and sliding distance. Conventional methods of predicting polyethylene wear in TKA mainly focus on peak contact stress or subsurface shear stress using finite element method analysis. By incorporating kinematics and contact stress, a new predictor for polyethylene wear in TKA (“Wear Index”) has been developed. The Wear Index was defined by multiplying deformation by femoro-tibial sliding velocity. The purpose of this study was to determine the predictive value of the Wear Index for polyethylene wear in TKA using both a numeric and an in vitro model.

Four commercially available total knee prostheses were modeled for this study. Deformation and sliding velocity were calculated based on the three-dimensional geometry of the components and the gait kinematic inputs using Hertz’s formula. One specimen of each of the four types of total knee prostheses was mounted on a custom-designed knee simulator. Vertical loads and flexion-extension uni-axial motion were simulated using computer controlled servohydraulic actuators. The same gait kinematic inputs used in the theoretical study were used in the simulation test. After the simulations, the surface of the tibial insert was examined microscopically and macroscopically and compared with the theoretically generated Wear Index.

This study showed a high correlation between the numeric model and the simulation. The depth of wear on the tibial insert correlated significantly with the Wear Index. Microscopic findings also demonstrated a good correlation between the Wear Index and observed wear patterns. Sliding velocity is an important factor for understanding wear in TKA. In conclusion, this study suggests that the Wear Index is a reliable predictor of polyethylene wear in TKA, as it incorporates both contact stress and kinematics in its calculation.

Introduction: Correct rotational alignment of the femoral component is an important factor for successful total knee arthroplasty. This study evaluated relationship between the transepicondylar axis and the posterior condylar axis in normal, varus, and valgus knees.

Methods: Thirty normal knees (mean age: 66.2 years), 30 osteoarthritic knees with varus deformity (67.9 years), and 25 osteoarthritic knees with valgus deformity (70.7 years) were evaluated using magnetic resonance imaging. Femo-rotibial angle on standing anteroposterior radiograph was 185° in the varus knees and 166.1° in the valgus knees. In the transverse view, the angle between the transepicondylar axis and the posterior condylar axis, and the angle between the line perpendicular to the anteroposterior (AP) axis and the posterior condylar axis were measured in each group.

Results: Transepicondylar line showed 6.4° of external rotation in the normal knees and 6.1 of external rotation in the varus knees relative to the posterior condylar axis. However, transepicondylar axis of the valgus knee showed 11.6° of external rotation. This angle was significantly larger than that of normal knee and varus knee (p < 0.05). The line perpendicular to the AP axis was externally rotated from the posterior condylar axis in 6.3° in the normal knees, 6.6° in the varus knees, and 8.8° in the valgus knees. The external rotational angle in the valgus knees was significantly larger than that of the normal and varus knees (p < 0.05).

Discussion and conclusion: These results suggest that there is no hypoplasia of the posterior part of the medial condyle in varus knees, however, posterior part of the lateral condyle in valgus knee is severely distorted. Based on the results of this study, 3 to 5 degrees of external rotation relative to the posterior condyles is not large enough to achieve correct rotational alignment for valgus knees.

Introduction: Analyses of the 3-D kinematics of TKA in vivo using the x-ray image matching techniques have been widely reported. However, the accuracy of those techniques has seemed not to be discussed enough. To demonstrate more accurate technique for those analyses, we developed the new calibration flame to detect the geometry of the x-ray source and more accurate image matching methods.

Materials and methods: A calibration flame was composed of four ball bearing markers. First, the optimal distributions of those ball markers were determined by computer simulations, and then, using the high-resolutional computed radiography (CR) of a metallic ball taken with the obtained optimal calibration flame, the resolving power of three degrees of freedom (DOF) translations were calculated. Next, the computer-synthesized projected images of the femoral component of TKA were calculated using the estimated x-ray source geometry and experimentally measured geometric data of the prosthesis when the full six DOF poses of the prosthesis were calculated. Matching the computer-synthesized images with the extracted and binalized 2-D CR images of the prosthesis was done automatically using computer in order to minimize the exclusive OR (XOR).

Results: The geometry of the x-ray source was estimated with accuracy of below 0.5 mm in computer simulations. The CR images of the prosthesis were matched with the computer-synthesized images until the XOR reached under one pixel and then, the accuracy of below 1.0 mm translations and 1.0 degrees rotation were recognized for the resolving power of six DOF poses of the prosthesis.

Discussion: The more accurate measurement of full six DOF poses is indispensable to estimate not only the 3-D kinematics but also the contact stresses or predicted polyethylene wear on TKA in vivo. The new calibration flame and the image matching technique we developed appear to be effective for analyses of TKA in vivo.