Assess the incidence of Vitamin D deficiency from a cohort of new referrals to a general Paediatric Orthopaedic outpatient clinic and evaluate the relationship between Vitamin D deficiency and the diagnosis of radiological or biochemical nutritional rickets. We performed a retrospective case note and biochemistry database review of all new patients seen in an elective Paediatric Orthopaedic clinic in the year 2010, who had Vitamin D levels measured. Radiographs were reviewed by the senior author to determine the presence or absence of radiological rickets. Biochemical rickets was diagnosed if there was deficient Vitamin D (< 20 mcg/ml) and raised PTH.Aim
Methods
Ottawa ankle rules originally described in 1992 have been shown to improve the pick-up rates of ankle fractures and avoid the need for unnecessary X-rays, thus minimising cost and radiation to the patient. We decided to carry out an audit at our hospital to look at the pick-up rates of ankle fractures and ways to minimise x-rays for the patient both in A&E and in the orthopaedic department. Ankle x-rays of 1088 trauma patients over a 7 month period from Dec 2009 to June 2010 (inclusive) were reviewed. Patients with ankle fractures were classified according to Weber type, and whether they were treated surgically or non-operatively. Non-operatively treated ankle fractures then formed the main sub-group of our study, looking at the number of follow-up X-rays and the amount of subsequent displacement. The amount of displacement was classified into non-displaced (0 mm), minimally displaced (<2mm) and displaced (>2 mm).Introduction
Methods
We have assessed the bone cuts achieved at surgery compared to the planned cuts produced during computer assisted surgery (CAS) using a CT free navigation system. In addition, two groups of matched patients were compared to assess the post-operative mechanical alignment achieved: 14 patients received a LCS total knee replacement (TKR) using the VectorVision module and 14 received a TKR using a conventional method of extramedullary alignment jigs The deviation in each plane (valgus-varus, flexion-extension and proximal-distal) was calculated. For the tibia the mean deviation in the coronal plane was 0.21 degrees of Varus (SD = 1.37) and in the sagittal plane was 1.29 degrees of flexion (SD = 3.73) and 0.24 mm of resection distal to the anticipated cut (SD = 2.14). For the femur the mean deviation in the coronal plane was 0.88 degrees (SD = 2.2) of valgus and in the sagittal plane the mean deviation was 0.3 degrees (SD = 2.91) of extension. In the transverse plane there was a mean deviation of 0.07 degrees (SD = 1.57) of external rotation. There was mean deviation of 2.33 mm of proximal resection (SD = 2.9) and 1.05 mm of anterior shift (SD = 2.81). On comparing the two groups, no statistically significant differences were found for the angles between the femoral component and the femoral mechanical axis, the tibial component and the tibial mechanical axis, the femoral and tibial mechanical axis and the femoral and tibial anatomical axis. We have demonstrated variation in the true bone cuts obtained using computer assisted surgery from those suggested by the software and have not demonstrated significant improvement in post-operative alignment. Justification for the extra cost, time and morbidity associated with this technology must be provided in the form of improved clinical outcomes in the future.
Total hip replacement is a successful and reliable procedure for the relief of pain, but the results achieved have been reported to be less successful in younger patients who tend to be relatively more active and place greater demands on prostheses than older patients. Between 1966 and 1978, 226 Charnley low friction arthroplasties (LFAs) were implanted in young patients with an average age at operation of 31.7 years. Initial results were presented at an average of 19.7 years. We have performed a further retrospective analysis of this cohort at 10 years on from the time of data collection of the original study. Of the original cohort, 112 patients are alive and either under follow-up at our hospital or have been traced to other hospitals. 16 have been lost to follow-up. Mean follow-up was 26.4 years. At the time of final follow-up or death, rate of aseptic loosening of the stem was approximately 80%. Acetabular components proved to be less successful with less than 60% remaining well fixed. Differences in survival were apparent between subgroups with differing original pathology with stem survival greater in those with DDH as opposed to rheumatoid or degenerative arthritis and the opposite being true for socket survival. This study adds to the available knowledge of the longevity of cemented total hip replacement as performed with unsophisticated cementation techniques and how it may perform in differing patients groups.
A secure bone cement interface between the acetabulum and the cement mantle of the hip socket is an important requirement for the long-term success of a cemented hip arthroplasty. Cement pressurisation after bone bed cleaning enables cement to penetrate interstices of cancellous bone forming a superior fixation strength. We designed an in-vitro experiment to evaluate the performance of the Exeter, Depuy T-handle and a plunger-type pressurisers using two parameters: cement penetration and cement pressurisation. The deformation of the flexible pressure head of the DePuy model produced a cement mantle, which is thick at the pole but tapered at its rim and variable in the amount of penetration produced (range 2–8mm) for an estimated similar force. Pressures of up to 60KPa were generated throughout the model acetabulum. The Exeter pressuriser was found to produce cement mantles more compatible with a socket. However, the test results show a wide variation in cement penetration occurring for what was estimated to be a similar applied force (3mm to 9mm at the pole and 5mm to 9mm at the rim). It was also shown to have the disadvantage of causing widely dissimilar pressures at the pole and the rim. The plunger protrusion required to produce 5mm cement penetration was found to be 7.5mm. Since this protrusion can be monitored and controlled by the operator, a cement intrusion of 5mm +/−1mm was found to be reproducible with the plunger-type device. The maximum variation in intrusion between rim and pole was 1 mm. Maximin pressures of 70KPa were generated. We have presented experimental evidence that suggests that a plunger type of acetabular cement pressuriser may provide a more consistently reproducible level of pressurisation leading to optimal cement penetration.