Introduction

Primary stability of the Burch-Schneider ring (BSR) in case of acetabular revision is discussed controversial. In a retrospective two centre cohort study we analyzed the influence of the mode of screw fixation and the restoration of the center of rotation on migration, loosening and other radiographic parameters.

Introduction

The usefulness of minimal invasive hip replacement is frequently discussed but there is a lack of data on the effect of the surgical approach on early results. We wanted to study the effect of the surgical approach on the peri- and early postoperative outcome.

Introduction: The original Müller straight stem (MSS, Zimmer^®; Winterthur, Switzerland) is made out of CoNiCr and showed excellent 20 year results but later modifications of the stem proved to be inferior. Aim of this study was to analyse the effect of shape, material and surface roughness on aseptic loosening of cemented Müller type straight stems.

Materials and patients: Between 1984 and 1996 a total of 926 THR were operated with four different versions of cemented Müller type straight stems and followed prospectively in the in-house register at our institution. Two different shapes of cemented Müller type straight stems (MSS and SL), both made out of two different alloys (CoNiCr and TiAl), were included in this study. All four versions differed in surface roughness (MSS CoNiCr Ra 1.0μm (satin); SL CoNiCr Ra 1.2μm (satin); MSS TiAl Ra 2.0μm (rough); SL TiAl Ra > 2.0μm (rough)). Survival analysis was done using Kaplan-Meier curves with aseptic loosening as endpoint, risk factors were tested with regression analysis.

Results: The 4 groups did not differ in age, gender and diagnosis, the mean follow up was 11.4 (0.1 to 23.0) years. Survival with aseptic loosening as endpoint was 97.7% (MSS CoNiCr), 96.4% (SL CoNiCr), 82.5% (MSS TiAl) and 67.4% (SL TiAl), respectively, at ten years. At final follow up all four groups differed significantly (p=0.044 Log rank test). Increasing roughness increased the risk for aseptic loosening and the harder CoCr had better survival than TiAl. results were significantly worse for the combination of the soft TiAl with a rough surface (SL TiAL, Ra > 2.0μm). For both stem designs the MSS shape had better survival than the SL shape (p=0.001)

Discussion: Wear modalities (abrasion vs. fretting) in the cement-stem interface are directly correlated with surface roughness, the amount of the released particles correlates with loosening. All examined stems had a roughness exceeding the limit of Ra =0.4 μm, producing abrasive wear with a higher volume of wear particles as compared to established polished stems which show fretting wear. Stem roughness and hardness are more important for long-term survival than some modifications in the shape.

Conclusion: Cemented Müller type straight stems should have a polished surface (Ra < 0.4 μm) and be made out of a hard material (CoNiCr) to minimize surface wear. This might be true for all types of cemented stems.

Introduction: The biological activity of PE-particles released due to wear is an established risk-factor for osteolysis and loosening after Total Hip Arthroplasty (THA). Cup position and orientation might have an effect on the risk of impingement and wear, thus contribute to the risk of aseptic loosening in the long-term what should be studied.

Methods: Between 1984 and 1987 a total of 149 cemented total hips (Müller all-poly cup, Müller straight stem, 32 mm head) have been implanted. All implants had a standardised clinical and radiological follow-up. The pre- and postoperative centre of rotation of the hip and the orientation of the cup were determined. Migration, linear wear and direction of wear were measured twice with standard Methods: and the digital EBRA method. Wear-volume was calculated, taking direction of wear and cup orientation into account. Radiographs were analysed for progressive osteolysis and loosening.

Results: 1 patient was lost to follow-up, 47 had died, 7 had been revised before 10 years follow-up. 18 patients had a missing or poor final radiograph, leaving 75 hips for long-term analysis. 41 were in male patients, mean age was 66.2 (+/− 11.0) years, mean follow-up 15.4 (+/−4.1) years. Mean inclination was 40.7° (+/− 7.1), mean anteversion was 14.8° (+/−8.4) And the mean cup positioning was 3.8 mm (+/− 4.3) medial and 5.3 mm (+/− 3.5) cranial.

Osteolysis was found in 36 cups, 18 of them have been revised.

The average linear wear was 1.1 (+/− 0.9) mm, the average wear volume 798.7 (+/−622.3) mm3, the linear wear rate 0.07 (+/−0.06) mm/year and the volumetric wear rate 54.5 (+/− 43.2) mm3/year.

Younger patients had increased linear wear rates (p=0.035). Osteolysis of the cup, cup migration and cup revision were correlated with linear and volumetric wear (all p=< 0.001).

There was no correlation of the cup position, inclination and anteversion with osteolysis, loosening and any of the wear parameters. Volume calculation did not provide further information.

Conclusion: We found a strong correlation between wear and loosening of PE cups, but cup position and orientation did not affect osteolysis and loosening. Thus in contrast to hard-hard bearings polyethylene is a forgiving bearing surface and improvement of the cup orientation (e.g. due to navigation) will not result in increased cup survival, as long as extreme positioning errors are avoided.