Introduction: Rabbits are a well-established animal model for orthopaedic research

and the tibia is commonly used for investigations of fracture repair with different implant materials

Therefore, a new method for the direct measurement of forces in the rabbit tibia was developed. The aim of this study was to determine maximal forces during weight bearing in the rabbit for future implementation into FEM-simulation.

Animals and Methods: An external ring fixation was attached to the left tibiae of 5 rabbits and an ostectomy followed. Force sensors were included into the collateral rods to incur the emerging forces completely. On each side, a measurement amplifier was applied to transfer the collected data telemetrically. During the study, the animals were weighted and x-rays were taken regularly. Measurements started 8 days postoperatively and were repeated 8 times until day 50 post-op. The rabbits were placed in a run and animated to move while the forces were registered. Force peaks were filtered from the collected data of each measurement as absolute values and relative to the animals’ weight (force-weight ratio/FWR).

Results: All included animals tolerated the external fixa-tion well and no clinical intolerances occurred. Beginning of callus formation was detected radiographically about 3 weeks post-op and all fixations could be removed 12–14 weeks after application without any permanent detriments. The maximal force amounted to 6950 g and 172 % FWR in animal 4 during the first recording. Means of the 5 maximal values for each measurement were located between 55 % FWR and 152 % FWR for the first measurement, converged to approx. 80 % FWR during the second recording 3 days later and descended to 20–40 % FWR until the end of the experiment.

Discussion: Aim of this study was to determine maximal forces during weight bearing in a rabbit model. Our model for in-vivo monitoring of these forces was practicable and provided profound data. The highest values occurred during the first or second recording. That coincides with the radiographic detection of callus after 3 weeks. Therefore, reliable measurements have to be carried out during the first 2 weeks postoperatively. Detected values show that the rabbit tibia is strained with up to 170 % of the body weight, which is the compressive force an implant in a weight bearing bone has to be able to bear. Future research will focus on the in-vivo monitoring of bending and torsion forces and the implementation of these data into FEM-simulation.

Introduction: Fractures in long bones are frequently managed with intramedullary implants, plates ore external fixators. X-ray images are normally used to determine the point of full weight bearing and implant removal. Plain radiographs give only poor information about the mechanical properties of the healing callus. Several quantitative Methods: like QCT and DEXA provide information about the density of the new bone, but the mechanical properties remain unknown. For direct monitoring of the mechanical properties of the healing callus a 4-point-stiffness device for small animals was constructed. This devise is used to detect the influence of degradable implants on bone healing. Long term aim is to develop “smart” implants that degrade during healing and speed up the healing process.

Materials and Methods: An uniplanar, bilateral external fixator was mounted on the tibiae of New Zealand White Rabbits after osteotomy and introduction of different degradable, intramedullar implants. The 4-point-bending measurement unit was temporarily fixed to record deflection with a non-contact displacement transducer. Load cells were instrumented to record the stepwise load increase (25g). The max. bending moment was only 0.14 Nm to avoid bending of the implant. Additional μ-CT analysis was conducted on the stiffness measurement days to quantify bone healing. After the in-vivo tests the stiffness measurement device was validated with ex-vivo measurements of bone models in a Material Test System (MTS).

Results: The bending stiffness unit showed a high precision with a standard deviation of 5.55E-04 N/μm and a mean deviation error of all models of 1.74E-04 N/μm. We found a significant non-linear correlation between the measured stiffness and the diameter of the models (p< 0.05, r2=0.96). Furthermore a significant correlation between the stiffness device and the MTS in vitro was shown (r2=0.96, p< 0.005). A significant correlation between the data of the bending stiffness device and the MTS was found for all animals (r2=0.64, p< 0.01). μ-CT analysis showed an increase in callus formation and density during the increase in bending stiffness.

Discussion: In this study a precise measurement unit to mirror the mechanical properties of healing bone is presented. The device was successfully tested in an in-vivo model of fracture healing. The healing of callus around different degradable implants can be monitored to develop implants that degrade during fracture healing to avoid stress shielding or implant removal. Not only data about the healing bone can be gatherd with the μ-CT analysis, but also processes around the implants can be well monitored to evaluate degradation and quality of the implants.