Introduction. Reverse Total Shoulder Arthroplasty (rTSA) is currently advised against in patient populations with movement disorders, due to potential premature failure of the implants from the use of walking assistive devices. The objective of this study is to measure the amount of displacement induced by the simulated loading of axillary crutches on a rTSA assembly in a laboratory mimicking immediate postoperative conditions. Methods. 8 reverse shoulder baseplate/glenosphere assemblies (Equinoxe, Exactech, Inc) were fixated to 15 lb/ft3 density rigid polyurethane bone substitute blocks. Displacement of the assemblies in the A/P and S/I axes was measured using digital displacement indicators by applying a physiologically relevant 357N shear load parallel to the face of the glenosphere, and a nominal 50N compressive axial load perpendicular to the glenosphere. Westerhoff et al. reported in vivo shoulder loads while ambulating with axillary crutches had a maximum resultant force of 170% times the patient's bodyweight with the arm at 45.25° of abduction1. This was recreated by applying a 1435.4N compressive load (Average bodyweight of 86.1kg*170%) to a humeral liner and reverse shoulder assembly in an Instron testing apparatus at 45.25° of abduction as shown in Figure 1. The glenosphere was rotated about the humeral component through the arc of the axillary crutch swing, from −5° of extension to 30° of flexion as shown in Figure 2 for 183,876 cycles2. The number of cycles was based on number of steps taken in a day from pedometer data reported by Tudor Locke et al. for patients with movement disorders, extrapolated out to a 6 week postoperative recovery period3. A Student's one-tailed, paired t-test was used to identify whether or not significant displacement occurred, where p<0.05 denoted a significant difference. Results. Displacement in the A/P and S/I axes before and after cyclic loading are presented in Table 1. The S/I direction showed no significant difference in displacement (p≤.0801), whereas the A/P direction showed significant increase in displacement (p≤.0340). The average increase in displacement in the A/P and S/I directions was 43.5 and 35.8 microns, respectively. Discussion and Conclusions. This study was designed to represent a worst case scenario, as a patient is unlikely to bear full bodyweight on crutches immediately postoperatively, and is also unlikely to take as many steps as a healthy individual until full recovery occurs. For these reasons, early results indicate statistically significant displacement could occur if a patient bears full bodyweight on axillary crutches immediately postoperatively. This risk could be lowered after the postoperative recovery period in combination with non-full weight bearing devices such as a cane or a walker. To view tables/figures, please contact authors directly

Proximal femoral focal deficiency is a congenital disorder of malformation of the proximal femur and/or the acetabulum. Patients present with limb length discrepancy and clinical features along a spectrum of severity. As these patients progress through to skeletal maturity and on to adulthood, altered biomechanical demands lead to progression of arthropathy in any joint within the lower limb. Abnormal anatomy presents a challenge to surgeons and conventional approaches and implants may not necessarily be applicable. We present a case of a 62-year-old lady with unilateral proximal femoral focal deficiency (suspected Aitken Class A) who ambulated with an equinus prosthesis for her entire life. She presented with ipsilateral knee pain and instability due to knee arthritis but could not tolerate a total knee arthroplasty due to poor quadriceps control. A custom osteointegration prosthesis was inserted with a view to converting to the proximal segment to a total hip replacement if required. The patient went on to develop ipsilateral symptomatic hip arthritis but altered acetabular anatomy required a custom tri-flange component (Ossis, Christchurch, New Zealand) and a custom proximal femoral component to link with the existing osseointegration component (Osseointegration Group of Australia, Sydney, Australia) were designed and implanted. The 18 month follow up of the custom hip components showed that the patient had Oxford hip scores that were markedly improved from pre-operatively. Knee joint heights were successfully restored to equal when the patient's prosthesis was attached. The patient describes feeling like “a normal person”, walks unaided for short distances and can ambulate longer distances with crutches. Advances in design and manufacture of implants have empowered surgeons to offer life improving treatments to patients with challenging anatomy. Using a custom acetabular tri-flange and osseointegration components is one possible solution to address symptomatic ipsilateral hip and knee arthropathy in the context of PFFD in adulthood

Introduction. Treatment of non-union in open tibial fractures Gustilo-Anderson(GA)-3A/3B fractures remains a challenging problem. Most of these can be dealt using treatment methods that requires excision of the non-union followed by bone grafting, masquelet technique, or acute shortening. Circular fixators with closed distraction or bone transport also remains a useful option. However, sometimes due to patient specific factors these cannot be used. Recently antibiotic loaded bone substitutes have been increasingly used for repairing infected non-unions. They provide local antibiotic delivery, fill dead space, and act as a bone conductive implant, which is resorted at the end of a few months. We aimed to assess the outcome of percutaneous injection of bone substitute while treating non-union of complex open tibial fractures. Materials & Methods. Three cases of clinical and radiological stiff tibial non-union requiring further intervention were identified from our major trauma open fracture database. Two GA-3B cases, treated with a circular frame developed fracture-related-infection(FRI) manifesting as local cellulitis, loosened infected wires/pins with raised blood-markers, and one case of GA-3A treated with an intramedullary nail. At the time of removal of metalwork/frame, informed consent was obtained and Cerament-G. TM. (bone-substitute with gentamicin) was percutaneously injected through a small cortical window using a bone biopsy(Jamshedi needle). All patients were allowed to weight bear as tolerated in a well-fitting air-cast boot and using crutches. They were followed up at 6 weekly intervals with clinical assessment of their symptoms and radiographs. Fracture union was assessed using serial radiographs with healing defined as filling of fracture gap, bridging callus and clinical assessment including return to full painless weight bearing. Results. Follow-up at 6 months showed all fractures had healed with no defect or gaps with evidence of new trabecular bone and significant resorption of Cerament-G. TM. at final follow-up. There was no evidence of residual infection with restoration of normal limb function. Fractures with no internal fixation showed a mild deformity that had developed during the course of the healing, presumed due to mild collapse in the absence of fixation. These were less than 10 degrees in sagittal and coronal planes and were clinically felt to be insignificant by the patients. Conclusions. Cerament-G's unique combination of high dose antibiotics and hydroxy apatite matrix provided by calcium sulphate might help provide an osteoconductive environment to allow these stiff non-unions to heal. The matrix appears to provide a scaffold-like structure that allows new bone in-growth with local release of antibiotics helping reduce deep-seated infections. The final deformation at fracture site underlines the need for fixation- and it is very unlikely that this technique will work in mobile nonunions. Whilst similar fractures may heal without the use of bone substitute injections, the speed of healing in presence of significant fracture gap suggests the use of these bone substitutes did help in our cases. Further studies with a larger cohort, including RCTs, to evaluate the effectiveness of this technique compared to other methods are needed

Introduction. Angular deformities of the distal femur can be corrected by opening, closing and neutral wedge techniques. Opening wedge (OW) and closing wedge (CW) are popular and well described in the literature. CW and OW techniques lead to leg length difference whereas the advantage of neutral wedge (NW) technique has several unique advantages. NW technique maintains limb length, wedge taken from the closing side is utilised on the opening side and since the angular correction is only half of the measured wedge on either side, translation of distal fragment is minimum. Leg lengths are not altered with this technique hence a useful technique in large deformities. We found no reports of clinical outcomes using NW technique. We present a technique of performing external fixator assisted NW correction of large valgus and varus deformities of distal femur and dual plating and discuss the results. Materials & Methods. We have treated 20 (22 limbs – 2 patients requiring staged bilateral corrections) patients for distal femoral varus and valgus deformities with CWDFO between 2019 and 2022. Out of these 4 patients (5 limbs) requiring large corrections of distal femoral angular deformities were treated with Neutral Wedge (NW) technique. 3 patients (four limbs) had distal femoral valgus deformity and one distal femoral varus deformity. Indication for NW technique is an angular deformity (varus or valgus of distal femur) requiring > 12 mm opening/closing wedge correction. We approached the closing side first and marked out the half of the calculated wedge with K – wires in a uniplanar fashion. Then an external fixator with two Schanz screws is applied on the opposite side, inserting the distal screw parallel to the articular surface and the proximal screw 6–7 cm proximal to the first pin and at right angles to the femoral shaft mechanical axis. Then the measured wedge is removed and carefully saved. External fixator is now used to close the wedge and over correct, creating an appropriate opening wedge on the opposite side. A Tomofix (Depuoy Synthes) plate is applied on the closing side with two screws proximal to osteotomy and two distally (to be completed later). Next the osteotomy on the opposite side is exposed, the graft is inserted. mLDFA is measured under image intensifier to confirm satisfactory correction. Closing wedge side fixation is then completed followed by fixation of opposite side with a Tomofix or a locking plate. Results. 3 patients (4 limbs) had genu valgum due to constitutional causes and one was a case of distal femoral varus from a fracture. Preoperative mLDFA ranged from 70–75° and in one case of varus deformity it was 103°. We achieved satisfactory correction of mLDFA in (85–90°) in 4 limbs and one measured 91°. Femoral length was not altered. JLCA was not affected post correction. Patients were allowed to weight bear for transfers for the first six weeks and full weight bearing was allowed at six weeks with crutches until healing of osteotomy. All osteotomies healed at 16–18 weeks (average 16.8 weeks). Patients regained full range of movement. We routinely recommend removal of metal work to facilitate future knee replacement if one is needed. Follow up ranged from 4 months to 2 yrs. Irritation from metal work was noted in 2 patients and resolved after removing the plates at 9 months post-surgery. Conclusions. NWDFO is a good option for large corrections. We describe a technique that facilitates accurate correction of deformity in these complex cases. Osteotomy heals predictably with uniplanar osteotomy and dual plate fixation. Metal work might cause irritation like other osteotomy and plating techniques in this location

Aim. To evaluate the efficacy of infection elimination and functional outcomes of the resection hip arthroplasty (RHA) with m. vastus lateralis flap plasty in patients with chronic recurrent periprosthetic joint infection (PJI) one year or later after the surgery. Method. We retrospectively studied the outcomes of 61 cases with recurrent PJI (more than 3 relapses). All patients underwent RHA with m. vastus lateralis flap plasty from the year 2005 to 2016. There were 35 males (63.6%) and 20 females (36.4%) with the mean age of 54 years. At least in one year after the surgery, the cases were analyzed for the absence of inflammation during the physical exam, functional result with the Harris hip score (HSS), quality of life with the Instrument for measurement of health-related quality of life scale and level of pain with the visual analogue scale (VAS). The results are presented as means with CI95%. Results. The mean follow-up period was 40.8 months. The overall mortality rate was 12.2% (n = 6). Of all patients, 3 (5.5%) had severe concomitant pathology and died due to systemic infection within 90 days after the surgery. Two more patients died during the period of 1–3 years. Prolonged remission of PJI was achieved in 91% (n = 50) patients. In 9% of cases (n = 5) the relapse of infection was achieved. The HHS corresponded to an unsatisfactory outcome with the mean value of 49.3 (45.4–53.3). Most of the patients (56%, n = 31) used 2 crutches while walking, 23% (n = 13) - a cane or a crutch, and 11% (n = 6) – a walker. In 73% of cases (n = 40), the load-bearing capacity of the operated limb was preserved. In 27% of cases (n = 15) the limb was non-supporting, including 10 patients with severe pain syndrome under the load. At the same time, the pain syndrome was absent in the rest of the patients. The mean VAS score was 2.77 (2.3–3.12). Despite the insufficient function of the operated limb, 83.6% of patients noted a satisfactory result with the mean Instrument for measurement of health-related quality of life* score of 57.8 (52.1–63.4). Conclusions. RHA with m. vastus lateralis flap plasty is a technically complex operation that in most cases leads to the elimination of chronic recurrent PJI. Apparently, the improvement of functional capabilities can be ensured by the use of revision arthroplasty or external fixation in order to form a supporting «new joint» (neoarthrosis). * EQ5D

Introduction. Total hip arthroplasty (THA) using short design stem is surging with increasing movement of minimally invasive techniques. Short stems are easier to insert through small incisions preserving muscles. We have used these types of short stems since 2010. Almost all of the patients have shown good clinical results. However, two patients developed fatigue fractures on femurs post operatively. We have reviewed the clinical and radiographic results of these patients. Patients and methods. From April 2010, we have performed 621 THAs with short design stems, Microplasty. R. , Biomet, using a muscle preservation approach, the Direct Anterior Approach (DAA). The age ranged from 31 to 88 years old. Case1: 56y.o. male, BMI 23.1kg/m. 2. Preoperative diagnosis was bilateral osteoarthritis. Simultaneous THAs were performed on bilateral hips. He was allowed to bear as much weight as he could tolerate using an assistive device immediately after surgery, and followed standard hip precautions for the first 3 weeks. He was discharged from hospital seven days after surgery and returned to his job two weeks after surgery. He noticed sudden left thigh pain three weeks after surgery without any obvious cause. Crutches were recommended to partially bear his weight. Six weeks after surgery, a fracture line became visible on the radiographs and new callus formation also became visible. Three months after surgery, he felt no pain and was able to walk without any crutches. Case2: 66y.o. female, BMI 27.5 kg/m. 2. Preoperative diagnosis was bilateral osteoarthritis. THAs were performed on the hips at a six month interval. The right hip was operated on first, followed by the left hip. She was discharged from hospital four days after surgery and returned to her job six weeks after surgery. Two months later after left hip surgery, she suddenly felt pain on her left femur without any obvious cause, and was unable to walk. Three weeks later, X-rays showed fatigue fracture lines and new callus formations. After two or three months using crutches, her pain improved and X-rays showed good callus formation and no stem subsidence. Discussions. Several reports showed insufficiency fractures of the pelvis following THA. But most of them occurred due to repetitive stress on fragile bones. But our cases showed no evidence of osteoporosis. They had no history of trauma. But they had some points in common, which were they were bilateral cases and their BMI were not low. The incident rate of fatigue fractures of femur with this short stem THAs was 0.3% in our cases. We suggested that one of the causes of these fatigue fractures was the shortness of the stems. The shortness of the stems concentrate the body weight to limited contact area of the femur, and the stress causes the fatigue fractures. We should consider the risk of fatigue fractures on the patients who are operated on bilaterally. However these two patients showed good callus formations and no stem subsidence after a few weeks of partial weight bearing

Purpose. The treatment of children with contractures involving the lower limbs is challenging. Many are confined to wheelchairs for several years till their potential to ambulate is discovered. The aim is to review the treatment and outcome of eight children treated for contractures and deformities of the lower limbs following confinement to wheelchairs. Methods. Eight children aged 4–14 years were treated for contractures of the hips, knees and feet between 2005 and 2011. The initial diagnosis was not made in 5 children. All children had never walked previously. Four patients were labelled “cerebral palsy”. All children were seen with a physiotherapist to assess their walking potential. Genetic and paediatric medical assessment was also made. Final diagnosis revealed arthrogryposis (n = 3) pterygium syndrome (n = 1) calcinosis cutis (n = 1) viral neuropathy (n = 1) and cerebral palsy (n = 2). Clinically all children were assessed to have good upper limb function for use of crutches. Surgical correction of the feet was required in 6 patients. Extension osteotomies of the knees were done in 8 patients following serial plaster cast treatment and hamstring release. Hip releases were done in 4 patients. Results. The osteotomies healed well following above knee cast immobilisation. All patients are ambulant with above knee calipers, anterior knee straps and boots. Two children required repeat extension osteotomies. Follow up ranges between 8 months to 5 years. Conclusion. Patients with contractures of the lower limb should have careful clinical assessment. If upper limb function is suitable for holding crutches and the patients have the potential to kneel with the body erect, careful preoperative planning should be undertaken to improve the foot for weight bearing and the knees with extension osteotomies and ambulation. Accurate diagnosis is essential

A seventy-five-year-old female patient presented with pain and deformity of her left leg of three days duration. Hybrid THRA has been done 11 years ago at her left hip for the treatment of osteoarthritis. Massive osteolysis and pathologic fracture were observed on plain radiograph (Fig. 1). Revision THRA using an allograft prosthesis composite (APC) was planned for solution of extensive bone loss of the proximal femur. Surgical exposure was performed through extended trochanteric osteotomy with the patient supine. Step-cut osteotomy was done at the remained proximal part of host femur to make match with the distal part of APC. Meticulous removal of granulation tissues and remaining cement was done. As Acetabular cup was stable, 60 mm sized high-walled polyethylene liner was exchanged. Calcar reconstruction prosthesis was cemented into a proximal femoral allograft measuring 15 cm and cement at the vicinity of the step-cut osteotomy was removed for later bony union at interface. After solid fixation of APC with cement, the distal half of APC was cemented with the host femur. Step-cut osteotomy was wired and autogenous bone grafts from the greater trochanter were added at the interface. Leg length and stability were rechecked using a standard necked 28 mm metal head and reduction was done stably. Greater trochanter was fixed over the trimmed proximal allograft with multiple wiring and paper-thin host femur was enveloped around the femoral allograft using absorbable sutures. Following insertion of the closed suction drainage drains, closure was done as routine fashion and healing of the wound was uneventful (Fig. 2). An abduction brace was applied post operatively for a period of four weeks. Crutch walking with partial weight bearing was started at four weeks and crutch protection was applied for a period of six months. Incorporation of allograft with the host bone was observed on two-year follow-up radiographs. At seven-year follow-up, the patient walks well with a mild limp, and Harris score is 90. We report on a seven-year follow-up case of revision THRA with APC with references (Fig. 3)

Introduction. Typical UK patients spend 5–7 days in hospital following total hip replacement (THR). Decreasing length of stay (LOS) increases throughput and reduces cost. We have developed a short stay THR programme (SSP), which has been used in all patients since May 2006; we present the first 100. Methods. Every patient undergoing THR is included in the dataset. All attend ‘bone school’ before admission, with talks and individual assessments by the senior sister, physiotherapist and occupational therapist. Medical concerns are discussed with an anaesthetist. Patients receive training with crutches; crutches are provided for home practice. All receive an uncemented Corail-Pinnacle THR via piriformis-sparing mini-posterior approach. ‘Low dose’ spinal plus light general anaesthesia provides sensory block whilst retaining motor function; painfree fully weightbearing mobilisation is predictably achieved within four hours. Following radiograph and haemoglobin check next morning, patients are discharged on meeting specific nursing/physiotherapy criteria. Those within 20 miles receive outreach follow-up. Follow-up assessment is undertaken using SF36, Visual Analogue, Merle d'Aubigné-Postel and Oxford Hip Scores. Results. Mean age was 65 years (25–91), mean BMI 28.7 (19–43), mean ASA 1.97 (1–3). Major complications were: one dislocation, one deep infection, one myocardial infarction. Several more minor complications occurred. Mean LOS was 1.99 nights (1–19). One patient was readmitted with wound ooze. No association existed between LOS and ASA/age. 82 patients remain under follow-up, (mean 37.8 months, range 36–61). Seven have died; four underwent revision; seven have moved away or been lost. 97% remain quite or very satisfied. Discussion. We believe our LOS to be amongst the shortest in the country, with favourable clinical results. The SSP succeeds by involving all team-members throughout, and managing patient expectation. At a time of limited healthcare resources we propose that our SSP is totally reproducible, and could readily be established elsewhere with similar benefits

Introduction and Purposes. Custom made acetabular prosthesis are a valid option for the reconstruction after the resection of pelvic tumors. They should guarantee a stable and reliable reconstruction for the expected survival of the patient. Nevertheless in many cases periacetabular metastatic lesions have been compared to high grade (IIIA-B) Paprosky defects, but treated with low or intermediate longevity implants. Some complex post-traumatic scenarios or total hip arthroplasty (THA) multiple failures need a reconstruction according to oncologic criteria to fill in the huge defect and to obtain an acceptable function. The aim of the study is to compare 3D custom-made implants for tumors and for THA failures. Materials and Methods. Three custom-made implants after tumor resection (group A: 1 chondroblastic osteosarcoma, 1 bifasic synovialsarcoma, 1 high grade chondrosarcoma) were evaluated and compared to 3 acetabular complex reconstructions after non-oncologic bone defect (group B: 3 cases of aseptic loosening after at least 2 revisions). All the implants were case-based designed, 3D printed, and realized with porous or trabecular surfaces on a Titanium base prosthesis. Age range 16–70 ys in oncologic patients and 60–75 ys in non-oncologic patients. The bone defect to be reconstructed after tumor resection was classified according to Enneking zones (1 type 1-2-3 resection, 1 type 2 resection, 1 partial type 2 resection). Non-oncologic cases were comparable in term of remaining bone stock and classified according to Paprosky classification for acetabular defects as 1 type IIIA an 2 type IIIB. Complications, MSTS functional score, necessity of walking-aids were evaluated at minimum follow up of 1 year. Results. In both groups, good functional results were obtained (MSTS score 25/30 in both groups). No cases of aseptic loosening and no infection occured. After 3 months of partial or no weight-bearing on the operated limb, 3 patients were able to walk unaided and 3 walked with one cane or crutch. No limb length discrepancy (major than 2 cm) were observed. Limping was present in oncologic cases due to muscle resection. Overall better results in term of satisfaction and quality of life were obtained in younger (oncologic) patients. Conclusions. Complex THA revision cases can sometimes be considered for a reconstruction with oncologic criteria. Even if indications are limited an acceptable functional results can be obtained. In the past for these cases a Girldestone resection was the only option. A collaboration among orthopaedic oncologist and hip arthroplasty surgeons is advisable in major orthopaedic centers to improve the prosthetic design and the functional results

Introduction. seeking full compliance with the Tissue Sparing Surgery principles, we introduced this new surgical approach to the coxa-femoral joint via the medial inguinal region. Method. we performed total hip arthroplasty on 20 patients suffering from hip arthritis while 15 cases of medial femoral fracture received hemiarthroplasty with bipolar prostheses implants. Outcome. reduced surgery times, lower blood loss, zero complications and significantly speedier recovery were observedin all the above cases. Argument. this new surgical approach we devised enables a quick, safe and easy replacement of the hip. The muscles of the hip remain totally unharmed; maximum exposure is gained, with visualization of the acetabulum, directly fronting the surgeon, at its very best, favourably comparing with any other known approach. No particular equipment is needed and no special operating table. And it does not in the least imply a steep learning curve. Dislocation risks are non-existent allowing the patient any position in bed immediately after surgery. It is aesthetically preferable, the scar remaining almost invisible in between the inguinal skin lines. The patient can at once resume a steady walk, Canadian crutches being needed only for the first few days. Conclusion. it is the authors' opinion that such a technique, thanks to its being safe, fast, economical and easy to replicate, results in undoubted benefits for the patient, not least because it requires much shorter and far easier rehabilitation; and it can be counted as a valid alternative for surgeons to the most common approaches currently in use

Treatment of osteoarthritis of the knee remains a challenging problem since the evolution of the disease may be different in each compartment of the knee, as well as the state of the ligaments. Total knee arthroplasty may provide a reliable long-lasting option but do not preserve the bone stock. In another hand, compartmental arthroplasty is a bone and ligament sparing solution to manage limited osteoarthritis of the knee affecting the medial, lateral or the patello-femoral compartment.1, 2, 3. Patient's selection and surgical indication are based on the physical examination and on the radiological analysis including full-length x-rays and stress x-rays. Clinical experience has shown the need for high flexion in patients who have both high flexibility and a desire to perform deep flexion. Additionally the shape differences related to anatomy or the patient expectations after the surgery may also affect the surgeon decision. 4. The limited incision into the extensor mechanism allows a quicker recovery which represents a functional improvement for the patient additionally to the cosmetic result. A dedicated physiotherapy starting on the following day allowing weight bearing exercises protected by crutches and focusing on early mobilization and range of motion combined to a multimodal pain management approach is critical despite the type of individualized solution chosen for the patient knee. 5. Since bony landmarks may be different form a patient to another one as well as anatomical shapes, several tools have been developed in order to provide the surgeons an assisted tool during the surgery adapted to each knee, this include navigation, patient specific instrumentation and robotic surgery

We all aware about overuse syndrome, as compensation of other parts of body. Our famous poet Sa'adi: when part of our body sustains become painful, the other parts can't tolerate and reciprocate. Among our patients who underwent total Knee arthroplasty few of them have pain especially in 1st 3 months (Anterior Knee pain, effusion, ….) but almost 15 – 20 percents are not satisfied enough by this Procedure. In a Cohort historic study on 301 TKA with at least 2 years follow up 47 patients had not enough satisfaction in our clinic we tried to visit them to find out why?. Criteria's we chose, were:. Age. Osteopenia. Sarcopenia. Low back pain. Spinal canal stenosis. Shoulders. Unstable blood pressure. Neuropathy. Eyes dysfunction. We exclude those who had problem by their new knees. 11 patients, all have been over age 68 years, and duration of start of symptoms in knee (s) to the surgery were more than 12 years, clearly showed painful arch of shoulder motion or frozen shoulder or established gleno humeral alone or G.H. and A.C. joints OA. Conclusion. Because of abnormal stand up of long lasting knee OA patients, they start to put pressure on their shoulder to climb on their body. Even their cane or crutches use are not in regular and academic rules. So, we nominate this entity: shoulder knee syndrome as a negative criteria that interferes in out come

Osteonecrosis of the femoral head (ONFH) is a debilitating, painful, progressive, and refractory disease that has multiple etiologic risk factors. It is caused by bone cell death, which itself has various causes, leading to femoral head collapse and subsequent osteoarthritis. ONFH primarily influences patients aged from 20 to 50 years; in addition, bilateral hip joints are involved in 75% of patients. Causes include use of corticosteroids, alcohol abuse, previous trauma, hemoglobinopathy, Gaucher disease, coagulopathies, and other diseases. No pharmacologic treatment has been shown to be effective for early ONFH. Outcomes of total hip arthroplasty (THA) for these young and active patients have some drawbacks, primarily due to the young age of these patients, limited lifetime and durability of the implants and their fixation, and the skeletal manifestations of osteonecrosis. As a result of these concerns, there has been an increased focus on early interventions for ONFH aimed at preservation of the native articulation. Core decompression is currently the most widely accepted surgical treatment at the early stage of avascular osteonecrosis (AVN); however, due to limited efficacy, its use has been debated. There is currently no standardised protocol for evaluating and treating osteonecrosis of the femoral head in adults in the United States. Although total hip replacement is the most frequent intervention for treatment of post-collapse (Steinberg stage-IIIB, IVB, V, and VI) osteonecrosis; core decompression is the most commonly offered intervention for symptomatic, pre-collapse (Steinberg stage-IB and IIB) osteonecrosis. Less frequently offered treatments include non-operative, pharmacologic or modality management, osteotomy, vascularised and non-vascularised bone-grafting, hemiarthroplasty, resurfacing and arthrodesis. A promising, minimally invasive, core decompression procedure combined with a mesenchymal stem cell grafting technique which restores vascularity and heals osteonecrotic lesions has become popularised. This procedure is called a bone marrow aspirate concentrate (BMAC) procedure. During a BMAC, mesenchymal stem cells (in the form of concentrated iliac crest bone marrow) are injected through a core decompression tract into the area of necrosis in the femoral head. Most patients with early (pre-collapse) disease have excellent results at 2 to 5 years of clinical follow-up. Patients are weight bearing as tolerated on crutches after the procedure for 6 weeks, and are able to go home on the same day or next day after surgery with minimal pain. We can report on the early, promising results of 300 patients with ONFH treated with BMAC in the United States by two expert hip surgeons with at least 75%-80% survivorship. The care of adults with osteonecrosis of the femoral head is highly variable. This paper will discuss the various non-operative and operative treatment algorithms for ONFH available today. We will also report on a promising, new technique (BMAC), which improves the efficacy of traditional core decompression for early ONFH. The goal of treatment of early ONFH is to avoid THA in young, active patients and this talk will discuss those interventions and treatments which help accomplish that goal

Purpose. To describe a 10-year long history of recurrent displacement and infection in a 37 yo female patient, HIV+/HCV+, with an history of drug addiction. Clinical History. Starting from avascular necrosis of the hip (caused by prolonged HAART therapy), the patient underwent first uncemented THA in 2003. One month after implant a septic mobilization due to local abscess was treated with first two stage revision surgery (modular stem with use of retention liner for intraoperatory instability and dislocation of the implant) that lasted for almost 6 years. After 6 years of apparent good clinical condition and stability of the implants, the patient came back with a septic state of the hip, and recurrent instability, caused by complete abruption of the cup from acetabulum (Figure 1) Another two stage revision was planned; patient suffered dislocation of the spacer in first hours after intervention and 3 months later was performed second stage revision (stem with modular neck and head, cup with augmentation metal liner). Three days later patient suffered from another dislocation, so implant was further revised (change of modular neck + dual mobility head/cup), and a pelvipodalic cast was even made, considering the poor compliance of the patient,. One month later, due to another local septic state of the hip and in consideration of clinical history, a DAIR procedure was performed with revision of limited modular components until intraoperative stability was assessed (metal spacer + metal liner + dual mobility head and cup). For further assurance, an external fixator was placed around the hip (Figure 2). Results. After last intervention no dislocation occurred and external fixation was removed with success after 2 months. Clinical outcome at 2 years showed a good functional outcome, and painless walking with only one crutch and limited limping. Discussion. This is a challenging case in which the comorbidity of immunosuppression, poor compliance of the patient and multiple hip revision surgery, started a very long sequence of complications and led to poor clinical results for years. Although the use of modularity aids reaching good stability and function in this kind of revision surgery, only a good control of general conditions of the patient and a multidisciplinary approach to correct patient's lifestyle has brought to stability and “up to now” endurance for this THA implant

Introduction. Fixation of the distal fibula in conjunction with ankle fractures has not changed over the last 50 years. The complication rate of these fixation techniques is as high as 30%. The fibula nail is an alternative method of fixation and uses a minimal invasive technique. This technique preserves soft tissue compared to previous techniques used, and fewer soft tissue complications. Method. We reviewed the preliminary results of 178 patients with unstable Weber B and C ankle fractures that were operated on in our unit between January 2012 and February 2013. We used the Acumed fibular nail for reduction and fixation of the lateral malleolus. Using the nail we had significant reduction in our operating time. Patients were discharged one day post operation without any POP and partial weight bearing on crutches. Various parameters were measured on all the follow- up x-rays and assessed for incongruencies compared with the normal ankle. These parameters were medial clearspace, talo-crural angle, talar tilt and fibular length. No patients thus far have had any loss of fixation. The Olerud and Molander score was used at three month and six month follow up. Results. Patients at three months scored an average of 80 and at six months an average of 85. There were no cases of non-union. 40 patients had systemic co-morbidities. We had four superficial wound complications that healed well with antibiotics and daily wound care. Conclusion. The fibula nail is an effective fixation technique for most Weber B and C ankle fractures. It causes minimal destruction of the soft tissue. Functional outcome of patients is excellent. NO DISCLOSURES

Femoral revision in cemented THA might include some technical difficulties, based on loss of bone stock and cement removal, which might lead to further loss of bone stock, inadequate fixation, cortical perforation or consequent fractures. Femoral impaction grafting, in combination with a primary cemented stem, allows for femoral bone restoration due to incorporation and remodelling of the allograft bone by the host skeleton. Historically it has been first performed and described in Exeter in 1987, utilizing a cemented tapered polished stem in combination with morselised fresh frozen bone grafts. The technique was refined by the development of designated instruments, which have been implemented by the Nijmegen group from Holland. Indications might include all femoral revisions with bone stock loss, while the Endo-Clinic experience is mainly based on revision of cemented stems. Cavitary bone defects affecting meta- and diaphysis leading to a wide or so called “drain pipe” femora, are optimal indications for this technique, especially in young patients. Contraindications are mainly: septical revisions, extensive circumferential cortical bone loss and noncompliance of the patient. Generally, the technique creates a new endosteal surface to host the cemented stem by reconstruction of the cavitary defects with impacted morselised bone graft. This achieves primary stability and restoration of the bone stock. It has been shown, that fresh frozen allograft shows superior mechanical stability than freeze-dried allografts. Incorporation of these grafts has been described in 89%. Technical steps include: removal of failed stem and all cement, reconstruction of segmental bone defects with metal mesh (if necessary), preparation of fresh frozen femoral head allografts with bone mill, optimal bone chip diameter 2–5 mm, larger chips for the calcar area (6–8 mm), insertion of an intramedullary plug including central wire, 2 cm distal the stem tip, introduction of bone chips from proximal to distal, impaction started by distal impactors over central wire, then progressive larger impactors proximal, insertion of a stem “dummy” as proximal impactor and space filler, removal of central wire, retrograde insertion of low viscosity cement (0.5 Gentamycin) with small nozzle syringe, including pressurization, and insertion of standard cemented stem. The cement mantle is of importance, as it acts as the distributor of force between the stem and bone graft and seals the stem. A cement mantle of at least 2 mm has shown favorable results. Post-operative care includes usually touch down weightbearing for 6–8 weeks, followed by 4–6 weeks of gradually increased weightbearing with a total of 12 weeks on crutches. Relevant complications include mainly femoral fractures due to the hardly impacted allograft bone. Subsidence of tapered polished implants might be related to cold flow within the cement mantle, however, could also be related to micro cement mantle fractures, leading to early failure. Subsidence should be less than 5 mm. Survivorship with a defined endpoint as any femoral revision after 10-year follow up has been reported by the Exeter group being over 90%, while survivorship for revision as aseptic loosening being above 98%. Within the last years various other authors and institutions reported about similar excellent survivorships, above 90%. In addition, a long-term follow up by the Swedish arthroplasty registry in more than 1180 patients reported a cumulative survival rate of 94% after 15 years. Impaction grafting might technically be more challenging and more time consuming than cement-free distal fixation techniques. It, however, enables a reliable restoration of bone stock which might especially become important in further revision scenarios in younger patients

BACKGROUND. During revision hip arthroplasty, removal of a well-fixed, ingrown metal acetabular component may not be possible. Therefore, a new polyethylene liner can be cemented into the existing shell via the cement locking mechanism. We report the indications, technique, and results of cementing an acetabular liner into a well-fixed cementless acetabular shell. PATIENTS AND METHODS. All patients were given informed consent to participate in this study, and the study was approved by our hospital institutional review board. Of 95 revision total hip arthroplasty (THA) between 2005 and 2014, five hips in 5 patients (4 female and a male) were operated by the cemented socket into metal shell technique. The mean age was 70.6 years (range, 59–84 years) (Table 1). Operative Technique. All operations were performed with the patient in the lateral decubitus position and using a posterolateral approach without osteotomy of the greater trochanter. After removal of broken polyethylene liner, an all-polyethylene socket (manufactured by Kyocera Corporation, Osaka, Japan) was cemented in the metal shell. In case of small metal shell, bone bed around the shell were augmented by the use of an impaction morselized allogeneic bone grafting, and the socket was cemented both in the metal shell and in the bone bed (Fig. 1). Postoperative Regimen. On the third postoperative day, the patients began a rehabilitation programmed by clinical path under the supervision of a physiotherapist. The use of crutches for ambulation was begun on the 10th to 14th postoperative day, with progressive weight-bearing as tolerated. Time to full weight-bearing was 3 to 4 weeks postoperatively. RESULTS. All of the cemented sockets functioned well and there were no failure cases during average follow-up period of 5 years (range, 0.7–9.5 years). DISCUSSION. Cementation of polyethylene liners into well-fixed metal shells has become a popular option during revision total hip arthroplasty (THA). Failure was always observed at the metal shell/cement interface whenever it did occur. The cement locking mechanism can be strengthened by roughening the backside of a smooth polyethylene liner to improve the cement-polyethylene interface, or by using an all-polyethylene acetabular component that is designed to be used with cement. Saw roughening of the polyethylene liner strengthens the poly-cement interface. We have used the all-polyethylene acetabular component with macrotexture anchoring form to cement fixation. To perform this procedure, an adequate shell diameter is necessary to accept an acetabular liner that will enable 2 mm of cement mantle around it. If an oversized polyethylene liner is cemented into a small acetabular metal shell, then there is the theoretical risk that the increased shear force will damage the cement locking mechanism, thus leading to failure of the construct. The case 1 in the current series, the hips had this situation, but no loosening occurred at final follow-up of 9.5 years postoperatively (Fig. 1). CONCLUSIONS. We reported good results with the use of a “cemented cup in cementless cup” technique in revision THAs, although follow-up periods were short-term to midterm. To view tables/figures, please contact authors directly

Purpose. Proximal femoral osteotomy is an attractive joint preservation procedure for osteonecrosis of the femoral head. The purpose of this study was to investigate the cause of failure of proximal femoral osteotomy in patients with osteonecrosis of the femoral head. Patients and Methods. Between 2008 and 2014, proximal femoral osteotomy was performed by one surgeon in 13 symptomatic hips. Ten trans-trochanteric rotational osteotomies (anterior: 7, posterior: 3) and 3 intertrochanteric curved varus osteotomy were performed. Of the patients, 9 were male and 1 was female, with a mean age at surgery of 36.9 years (range, 25–55 years). The mean postoperative follow-up period was 38 months (range, 12–72 months). Three patients (4 hips) had steroid-induced osteonecrosis, and 7 (9 hips) had alcohol-associated osteonecrosis. At 6 postoperative weeks, partial weight bearing was permitted with the assistance of 2 crutches. At more than 6 postoperative months, full weight bearing was permitted. Patients who had the potential to achieve acetabular coverage of more than one-third of the intact articular surface on preoperative hip radiography, computed tomography, and magnetic resonance imaging were considered suitable for this operation. A clinical evaluation using the Japanese Orthopaedic Association (JOA) scoring system and a radiologic evaluation were performed. Clinical failure was defined as conversion to total hip arthroplasty (THA) or progression to head collapse and osteoarthritis. The 13 hips were divided into two groups, namely the failure and success groups. Results. The mean preoperative JOA score was 59 points. The score in the success group (7 hips) improved to 89 points at the time of final follow-up. In the failure group (6 hips), 5 hips were converted to THA because of progression to secondary collapse or osteoarthritis in a mean postoperative period of 35 months (range, 24–51 months). After converting to THA, good clinical and radiographic results were achieved, except in 1 patient who had incomprehensible severe pain around the affected hip. Advanced osteoarthritis was observed in 1 hip awaiting THA. Various factors cause failure of proximal femoral osteotomy, such as difficulty in controlling the underlying disease with less than 10 mg of steroid (Fig. 1), overuse of the affected hip within 6 postoperative months without the physician's consent, vascular occlusion after total necrosis of the femoral head as a result of damage to the nutritional vessel during or after the operation, and incorrect judgement of the indication of the operation and the extent of the intact load-bearing area. Conclusion. We think that full weight bearing should be permitted postoperatively only after more than 6 months, and heavy work and sport, only after more than 1 year. Efforts should be made to improve surgeons' skill in proximal femoral osteotomy and accurate judgement of imaging data. For steroid-induced osteonecrosis of the femoral head, proximal femoral osteotomy is an acceptable procedure for relieving pain if the underlying disease can be controlled with not more than 5 mg of steroid

Femoral revision in cemented THA might include some technical difficulties, based on loss of bone stock and cement removal, which might lead to further loss of bone stock, inadequate fixation, cortical perforation or consequent fractures. Femoral impaction grafting, in combination with a primary cemented stem, allows for femoral bone restoration due to incorporation and remodeling of the allograft bone by the host skeleton. Historically, it has been first performed and described in Exeter in 1987, utilizing a cemented tapered polished stem in combination with morselised fresh frozen bone grafts. The technique was refined by the development of designated instruments, which have been implemented by the Nijmegen group from Holland. Indications might include all femoral revisions with bone stock loss, while the ENDO-Klinik experience is mainly based on revision of cemented stems. Cavitary bone defects affecting meta- and diaphysis leading to a wide or so called “drain pipe” femora, are optimal indications for this technique, especially in young patients. Contraindications are mainly: septical revisions, extensive circumferential cortical bone loss and noncompliance of the patient. Generally the technique creates a new endosteal surface to host the cemented stem by reconstruction of the cavitary defects with impacted morselised bone graft. This achieves primary stability and restoration of the bone stock. It has been shown, that fresh frozen allograft shows superior mechanical stability than freeze-dried allografts. Incorporation of these grafts has been described in 89%. Technical steps include: removal of failed stem and all cement, reconstruction of segmental bone defects with metal mesh (if necessary), preparation of fresh frozen femoral head allografts with bone mill, optimal bone chip diameter 2 – 5 mm, larger chips for the calcar area (6 – 8 mm), insertion of an intramedullary plug including central wire, 2 cm distal to the stem tip, introduction of bone chips from proximal to distal, impaction started by distal impactors over central wire, then progressively larger impactors proximal, insertion of a stem “dummy” as proximal impactor and space filler, removal of central wire, retrograde insertion of low viscosity cement (0.5 Gentamycin) with small nozzle syringe, including pressurization, insertion of standard cemented stem. The cement mantle is of importance, as it acts as the distributor of force between the stem and bone graft and seals the stem. A cement mantle of at least 2 mm has shown favorable results. Originally the technique is described with a polished stem. We use standard brushed stems with comparable results. Postoperative care includes usually touch down weight bearing for 6–8 weeks, followed by 4–6 weeks of gradually increased weightbearing with a total of 12 weeks on crutches. Survivorship with a defined endpoint as any femoral revision after 10 year follow up has been reported by the Exeter group being over 90%. While survivorship for revision related to aseptic loosening being above 98%. Within the last years various other authors and institutions reported similar excellent survivorships, above 90%. In addition a long term follow up by the Swedish arthroplasty registry in more than 1180 patients reported a cumulative survival rate of 94% after 15 years. Impaction grafting might technically be more challenging and more time consuming than cement free distal fixation techniques. It, however, enables a reliable restoration of bone stock which might become important in further revision scenarios in younger patients