Introduction. Stiffness after total knee arthroplasty (TKA) has been reported to occur due to component malpositioning and/or oversizing, improper femoral component (FC) flexion and tibial component (TC) slope, tight extension gap, inaccurate joint line placement, deficient posterior osteophyte resection, heterotopic ossification (HO), poor patellofemoral joint reconstruction, poor posterior condylar offset restoration, and/or posterior cruciate ligament (PCL) under-resection or retraction. However, the importance of these potential factors for stiffness are not well documented in the medical literature. The aim of this study was therefore to evaluate specific radiographic parameters in patients who had stiffness after primary TKA. Material and Methods. An IRB-approved retrospective chart review was performed to identify patients that were revised due to stiffness after TKA. We defined stiffness as 15º or more of flexion contraction, less than 75º of flexion or a range of motion (ROM) of 90º with the chief complaint of limited ROM and pain. Patients with history of previous revisions and/or ORIF, infection, or isolated polyethylene exchange were excluded. Patients with a minimum of 1 year radiographic follow-up were included. Radiographic measurements were performed as described by the Knee Society TKA Roentgenographic Evaluation System (KSRES). Two blinded observers performed all measurements. Descriptive data is reported as mean (range). Inter-observer correlations were reported using Intraclass correlations coefficient (ICC). Results. A total of 44 patients met the inclusion criteria. Of those, 13 (30%) were male and 31 (70%) were female. Mean BMI was 33.9 kg/m2 (19.5–58). ICCs ranged from good to excellent (>0.8) for all measurements performed. Coronal FC and TC alignments were 95.29º (82.4º–100.6º) and 89.16º (84.4º–94.2º) respectively. HO ranged from 0 to 3 (0:43%, 1:36%, 2:11%, 3:10%). FC-Flexion and TC-slope were 10.17 (3.5–19.8) and 86.7 (61.2–99.2) respectively. Insall-Salvati ratio was 1.01 (0.58–2.04). Posterior condylar offset (CO) ratio was 0.51 (0.34–1.11). Anterior CO ratio was 0.2 (0–0.34). Anterior femoral cortex notching ranged from 0 to 3 (0:39%, 1:43%, 2:14%, 3:4%). Femoral posterior osteophytes were observed in 32% of patients. A gap between the anterior flange and the femoral cortex was observed in 45% of patients. The patella was resurfaced in 93% of patients with a mean patellar tilt and patellar displacement of 5.34º (−8.9º to 5.34º) and 9.88% (−5 to 41%) respectively. Conclusion. To our knowledge this is the first study reporting specific radiographic data on postoperative stiffness following primary TKA. From the observed radiographic measurements, the increased mean femoral component flexion, the high amount of postoperative HO and posterior osteophytes, and the anterior cortical and component gap suggest possible risk factors influencing the occurrence of postoperative stiffness. Future focus will include a matched control population of patients in order to establish statistical significance of all observed values

Shoulder arthroplasty is effective at restoring function and relieving pain in patients suffering from glenohumeral arthritis; however, cortex thinning has been significantly associated with larger press-fit stems (fill ratio = 0.57 vs 0.48; P = 0.013)1. Additionally, excessively stiff implant-bone constructs are considered undesirable, as high initial stiffness of rigid fracture fixation implants has been related to premature loosening and an ultimate failure of the implant-bone interface2. Consequently, one objective which has driven the evolution of humeral stem design has been the reduction of stress-shielding induced bone resorption; this in-part has led to the introduction of short stems, which rely on metaphyseal fixation. However, the selection of short stem diametral (i.e., thickness) sizing remains subjective, and its impact on the resulting stem-bone construct stiffness has yet to be quantified.

Eight paired cadaveric humeri (age = 75±15 years) were reconstructed with surgeon selected ‘standard’ sized and 2mm ‘oversized’ short-stemmed implants. Standard stem sizing was based on a haptic assessment of stem and broach stability per typical surgical practice. Anteroposterior radiographs were taken, and the metaphyseal and diaphyseal fill ratios were quantified. Each humerus was then potted in polymethyl methacrylate bone cement and subjected to 2000 cycles of compressive loading representing 90º forward flexion to simulate postoperative seating. Following this, a custom 3D printed metal implant adapter was affixed to the stem, which allowed for compressive loading in-line with the stem axis (Fig.1). Each stem was then forced to subside by 5mm at a rate of 1mm/min, from which the compressive stiffness of the stem-bone construct was assessed. The bone-implant construct stiffness was quantified as the slope of the linear portion of the resulting force-displacement curves.

The metaphyseal and diaphyseal fill ratios were 0.50±0.10 and 0.45±0.07 for the standard sized stems and 0.50±0.06 and 0.52±0.06 for the oversized stems, respectively. Neither was found to correlate significantly with the stem-bone construct stiffness measure (metaphysis: P = 0.259, diaphysis: P = 0.529); however, the diaphyseal fill ratio was significantly different between standard and oversized stems (P < 0.001, Power = 1.0). Increasing the stem size by 2mm had a significant impact on the stiffness of the stem-bone construct (P = 0.003, Power = 0.971; Fig.2). Stem oversizing yielded a construct stiffness of −741±243N/mm; more than double that of the standard stems, which was −334±120N/mm.

The fill ratios reported in the present investigation match well with those of a finite element assessment of oversizing short humeral stems3. This work complements that investigation's conclusion, that small reductions in diaphyseal fill ratio may reduce the likelihood of stress shielding, by also demonstrating that oversizing stems by 2mm dramatically increases the stiffness of the resulting implant-bone construct, as stiffer implants have been associated with decreased bone stimulus4 and premature loosening2. The present findings suggest that even a small, 2mm, variation in the thickness of short stem humeral components can have a marked influence on the resulting stiffness of the implant-bone construct. This highlights the need for more objective intraoperative methods for selecting stem size to provide guidelines for appropriate diametral sizing.

For any figures or tables, please contact the authors directly.

Decreased ankle dorsiflexion is common after injury and may result in patient complaints of stiffness and subsequent injury. The weight-bearing lunge test (WBLT) is a simple clinical measure of dorsiflexion. Previous study has defined a 2.0cm side-to-side discrepancy in WBLT as likely significant. With review of current literature, ankle stiffness is a concept largely undefined; we aim to relate patient complaints of stiffness to WBLT.

This was a population-based inception cohort with longitudinal follow-up. Patients between ages 18–65 receiving surgical fixation for ankle fracture were screened. Pilon/plafond fractures, bilateral injuries, or polytrauma were excluded. At 6-weeks, 6-months, and 1-year WBLT was measured along with non-weight-bearing goniometry; and an Olerud-Molander ankle score completed.

155 patients were recruited (90 female, 65 male; mean age 42, range 20–67). 47% of injuries were unimalleolar, 17% bimalleolar, and 36% trimalleolar; 35% received syndesmotic fixation. 89% of patients reported feeling stiff at 6-weeks, 82% at 6-months, and 74% at 1-year. 98% of patients had ≥2.0cm discrepancy of WBLT at 6-weeks, 78% at 6-months, and 72% at 1-year. Different thresholds of WBLT (larger discrepancy or absolute negative measurement) had worse correlation with patient reported stiffness.

Our population had high incidence of stiffness at 1-year. The proportion of patients complaining of stiffness after ankle fracture was similar to that measured with ≥2.0cm discrepancy of WBLT. This is the first study that we are aware of that relates the WBLT and the previously reported threshold of 2.0cm to stiffness. This measurement may give clinicians a better objective idea regarding patient perception of a “stiff” ankle. Reducing side to side discrepancy in range of motion should be considered in rehabilitation rather than total range of motion.

Despite total knee arthroplasty demonstrating high levels of success, 20% of patients report dissatisfaction with their result.

Wellness Stasis Socks are embedded with a proprietary pattern of neuro-receptor activation points that have been proven to activate a precise neuro-response, as according to the pattern theory of haptic perception, which stimulates improvements in pain and function.

Technologies that manipulate this sensory environment, such as textured insoles, have proven to be effective in improving gait patterns in patients with knee osteoarthritis. In regard to patients undergoing TKA using this new technology may prove beneficial as an adjunct to recovery as many patients suffer from further deficits to their proprioceptive system caused by ligamentous damage and alterations to mechanoreceptors during procedure. We hypothesized that the Wellness Stasis Socks are a safe, cost-effective and easily scalable strategy to support TKA patients through their recovery.

Double-blinded, placebo-controlled randomized trial. Randomization using a computer-generated program . All study coordinators, healthcare personel and patients were blinded to patient groups. All surgical procedures were conducted by the same technique and orthopaedic surgeon. Intervention group: Wellness Stasis socks containing receptor point-activation technology. Control group: indentical appearing Wellness Stasis socks without receptor point-activation technology. Sock use during the waking hours . All additional post-operative protocols remained consistent between groups including same facility physiotherapy . Additional modalities (ice machines, soft-tissue massages, acupuncture) were prohibited. WOMAC questionnaire completed at baseline, 2 weeks, and 6 weeks to assess pain, stiffness and physical function. G^*Power software to determine minimum sample of 50 in each group. No patients were lost to follow up and all followed study protocol. Data analysis using SPSS software. P-values, effect sizes, and confidence intervals are reported to assess clinical relevance of the finding. Physical status classifications were compared using t-test. Within-subject and between-subject differences in the mean WOMAC were analyzed by ANOVA.

Cramer's V statistical analysis noted that other variables of Sex, BMI, ASA classification and Age were not statistically different between the control and intervention groups.

No statistical difference between groups in Preop Womac scores.

The data showed a consistent improvement in Womac scores for pain and stiffness at 2 weeks post op in the interventional group over the control group.

The womac scores assessing physical function showed a consistent improvement at both 2 and 6 weeks post op in the intervention group compared to the control group.

There were no complications in either group associated the sock use.

The intervention proved to be a low cost and safe additional intervention post operatively from TKA to help patients improve with regard to pain, stiffness and physical function.

This study suggests this modality can be added to the list of other commonly used post op interventions such as cryocuffs, physiotherapy, and relaxation techniques as safe post op interventions to help patients improve post op TKA and can act as an adjunct in providing non narcotic pain control .

Hemiarthroplasty is a common procedure that is an attractive alternative to total arthroplasty because it conserves natural tissue, allows for quicker recovery, and has a lower cost. One significant issue with hemiarthroplasties is that they lead to accelerated wear of the opposing native cartilage, likely due to the high stiffness of the implant. The purpose of this study was to investigate the range of currently available biomaterials for hemiarthroplasty applications. We employed a finite-element (FE) model of a radial head implant against the native capitellum as our joint model.

The FE model was developed in ABAQUS v6.14 (Dassault Systèmes Simulia Corp., Providence, RI, USA). A solid axisymmetric concave implant with seven different materials and the native radial head were evaluated, six modelled as elastic materials with different Young's moduli (E) and Poisson's Ratios (ν), and one modelled as a Mooney-Rivlin hyperelastic material. The materials investigated were CoCr (E=230 GPa, ν = 0.3), PEEK (E=3.7 GPa, ν = 0.36), HDPE (E=2.7 GPa, ν = 0.42), UHMWPE (E=0.69 GPa, ν = 0.49), Bionate 75D (E=0.288 GPa, ν = 0.39), Bionate 55D (E=0.039 GPa, ν = 0.45), and Bionate 80A (modelled as a Mooney-Rivlin hyperelastic material). A load of 100 N was applied to the radius through the center of rotation representing a typical load through the radius. The variable of interest was articular contact stress on the capitellum.

The CoCr implant had a maximum contact stress over 114% higher than the native radial head. By changing the material to lower the stiffness of the implant, the maximum contact stress was 24%, 70%, 105%, 111%, 113%, and 113% higher than the native radial head for Bionate 80A, Bionate 55D, Bionate 75D, UHMWPE, HDPE, and PEEK respectively.

This work shows that lowering implant stiffness can reduce the contact stress on cartilage in hemiarthroplasty implants. By changing the material below a Young's modulus of ∼100 MPa elevated stresses on the capitellum can be markedly reduced and hence potentially reduce or prevent degenerative changes of the native articulating cartilage. Low stiffness implant materials are not a novel concept, but to date there have been few that investigate materials (such as Bionate) as a potential load bearing material for implant applications. Further work is required to assess the efficacy of these materials for articular bearing applications.

The meniscus is comprised largely of type I collagen, as well as fibrochondrocytes and proteoglycans. In articular cartilage and intervertebral disc, proteoglycans make a significant contribution to mechanical stiffness of the tissue via negatively charged moieties which generate Donnan osmotic pressures. To date, such a role for proteoglycans in meniscal tissue has not been established. This study aimed to investigate whether meniscal proteoglycans contribute to mechanical stiffness of the tissue via electrostatic effects.

Following local University Ethics Committee approval, discs of meniscal tissue two millimetres thick and of five millimetres diameter were obtained from 12 paired fresh frozen human menisci, from donors < 6 5 years of age, with no history of osteoarthritis or meniscal injury. Samples were taken from anterior, middle and posterior meniscal regions. Each disc was placed within a custom confined compression chamber, permeable at the top and bottom only and then bathed in one of three solutions − 0.14M PBS (mimics cellular environment), deionised water (negates effect of mobile ions) or 3M PBS (negates all ionic effects). The apparatus was mounted within a Bose Electroforce 3100 materials testing machine and a 0.3N preload was applied. The sample was allowed to reach equilibrium, before being subjected to a 10% ramp compressive strain followed by a 7200 second hold phase. Equal numbers of samples from each meniscus and meniscal region were tested in each solution. Resultant stress relaxation curves were fitted to a nonlinear poroviscoelastic model with strain dependent permeability using FEBio finite element modelling software. Goodness of fit (R2) was assessed using a coefficient of determination. All samples were assayed for proteoglycan content. Comparison of resultant mechanical parameters was undertaken using multivariate ANOVA with Bonferroni adjustment for multiple comparisons.

36 samples were tested. A significant difference (p < 0 .05) was observed in the value of the Young's modulus (E) between samples tested in deionised water compared to 0.14M/3M PBS, with the meniscus found to be stiffest in deionised water (E = 1.15 MPa) and least stiff in 3M PBS (E = 0.43 MPa), with the value of E in 0.14M PBS falling in between (0.68 MPa). No differences were observed in the zero strain permeability or the exponential strain dependent/stiffening coefficients. The viscoelastic coefficient and relaxation time values were not found to improve model fit and were thus held at zero. The mean R2 value was 0.78, indicating a good fit and did not differ significantly between solutions. Proteoglycan content was not found to differ with solution, but was found to be significantly increased in the middle region of both menisci.

Proteoglycans make a significant electrostatic contribution to mechanical stiffness of the meniscus, increasing it by 58% in the physiological condition, and are hence integral to its function. It is important to include the influence of ionic effects when modelling meniscus, particularly where fluid flow or localised strain is modelled. From a clinical perspective, it is critical that meniscal regeneration strategies such as scaffolds or allografts attempt to preserve, or compensate for, the function of proteoglycans to ensure normal meniscal function.

Adult articular cartilage mechanical functionality is dependent on the unique zonal organization of its tissue. Current mesenchymal stem cell (MSC)-based treatment has resulted in sub-optimal cartilage repair, with inferior quality of cartilage generated from MSCs in terms of the biochemical content, zonal architecture and mechanical strength when compared to normal cartilage. The phenotype of cartilage derived from MSCs has been reported to be influenced by the microenvironmental biophysical cues, such as the surface topography and substrate stiffness. In this study, the effect of nano-topographic surfaces to direct MSC chondrogenic differentiation to chondrocytes of different phenotypes was investigated, and the application of these pre-differentiated cells for cartilage repair was explored.

Specific nano-topographic patterns on the polymeric substrate were generated by nano-thermal imprinting on the PCL, PGA and PLA surfaces respectively. Human bone marrow MSCs seeded on these surfaces were subjected to chondrogenic differentiation and the phenotypic outcome of the differentiated cells was analyzed by real time PCR, matrix quantification and immunohistological staining. The influence of substrate stiffness of the nano-topographic patterns on MSC chondrogenesis was further evaluated. The ability of these pre-differentiated MSCs on different nano-topographic surfaces to form zonal cartilage was verified in in vitro 3D hydrogel culture. These pre-differentiated cells were then implanted as bilayered hydrogel constructs composed of superficial zone-like chondro-progenitors overlaying the middle/deep zone-like chondro-progenitors, was compared to undifferentiated MSCs and non-specifically pre-differentiated MSCs in a osteochondral defect rabbit model.

Nano-topographical patterns triggered MSC morphology and cytoskeletal structure changes, and cellular aggregation resulting in specific chondrogenic differentiation outcomes. MSC chondrogenesis on nano-pillar topography facilitated robust hyaline-like cartilage formation, while MSCs on nano-grill topography were induced to form fibro/superficial zone cartilage-like tissue. These phenotypic outcomes were further diversified and controlled by manipulation of the material stiffness. Hyaline cartilage with middle/deep zone cartilage characteristics was derived on softer nano-pillar surfaces, and superficial zone-like cartilage resulted on softer nano-grill surfaces. MSCs on stiffer nano-pillar and stiffer nano-grill resulted in mixed fibro/hyaline/hypertrophic cartilage and non-cartilage tissue, respectively. Further, the nano-topography pre-differentiated cells possessed phenotypic memory, forming phenotypically distinct cartilage in subsequent 3D hydrogel culture. Lastly, implantation of the bilayered hydrogel construct of superficial zone-like chondro-progenitors and middle/deep zone-like chondro-progenitors resulted in regeneration of phenotypically better cartilage tissue with higher mechanical function.

Our results demonstrate the potential of nano-topographic cues, coupled with substrate stiffness, in guiding the differentiation of MSCs to chondrocytes of a specific phenotype. Implantation of these chondrocytes in a bilayered hydrogel construct yielded cartilage with more normal architecture and mechanical function. Our approach provides a potential translatable strategy for improved articular cartilage regeneration using MSCs.

Introduction

A stiff total knee arthroplasty (TKA) is an uncommon but disabling problem because it causes pain and limited function. Revision surgery has been reported as a satisfactory treatment option for stiffness with modest benefits. The aim of this study was to evaluate the results of revision surgery for the treatment of stiffness after TKA.

Introduction

The increase in revision joint replacement surgery and fractures of bone around orthopaedic implants may be partly addressed by keeping bone healthy around orthopaedic implants by inserting implants with mechanical properties closer to the patient's bone properties. We do not currently have an accurate way of calculating a patient's bone mechanical properties. We therefore posed a simple question: can data derived from a micro-indenter be used to calculate bone stiffness?

Total shoulder arthroplasty (TSA) and reverse shoulder arthroplasty (RSA) are excellent surgical options for individuals with shoulder arthritis, providing good to excellent results in the vast majority of patients. Complications are rare, but can be devastating for both the patient and surgeon. An uncommon, but extremely problematic complication following shoulder arthroplasty is shoulder stiffness. While substantial literature discussing post-arthroplasty stiffness is available for other joints such as the hip, knee, and elbow, there is a paucity of research available discussing this complication in the shoulder. As noted in multiple reviews, diminished range of motion following TSA or RSA may be due to a number of factors, including pre-operative diagnosis of proximal humerus fracture, inadequate post-operative rehabilitation, implant-related factors such as malpositioning and/or inappropriate-sized implants, and heterotopic ossification. Often, pathology leading to post-arthroplasty stiffness involves scarring of the long head of the biceps tendon, rotator cuff impingement, as well as cuff tendonitis. Periprosthetic joint infection (PJI) is also important to recognise, and may be difficult to diagnose, especially in cases of Propionibacterium acnes infections. Importantly, PJI may present with stiffness as well as instability, and thus a high index of suspicion with a low threshold to aspirate is necessary in these challenging patients. Treatment of patients with stiffness following arthroplasty is challenging, and may involve arthroscopic intervention with or without manipulation, as well as manipulation under anesthesia alone. This paper will discuss the etiology, work-up, and treatment of patients with shoulder stiffness following TSA and RSA.

While the definition of “stiffness” after shoulder arthroplasty remains controversial, loss of range of motion in the post-arthroplasty setting can be a disabling functional complication. Fortunately, the incidence of post-operative loss of both active and passive range of motion is relatively less common following shoulder replacement procedures. Certain pre-operative diagnoses (proximal humeral fracture, capsulorraphy arthropathy, revision arthroplasty) are associated with post-operative soft tissue contractures. Certain medical comorbidities (diabetes, inflammatory arthropathy) are associated with periarticular capsular adhesions at the intracellular level.

Management of the “stiff” shoulder arthroplasty must account for several confounding variables:

Appropriateness of diagnosis leading to arthroplasty

Techniques for management include soft tissue contracture release (manipulation, arthroscopic, open) and component revision.

Back pain is a significant socio-economic problem affecting around 80% of the population at some point during their lives. Chronic back pain leads to millions of days of work absence per year, posing a burden to health services around the world. In order to assess surgical interventions, such as disc replacements and spinal instrumentations, to treat chronic back pain it is important to understand the biomechanics of the spine and the intervertebral disc (IVD). A wide range of testing protocols, machines and parameters are employed to characterise the IVD, making it difficult to compare data across laboratories.

The aim of this study was to compare the two most commonly used testing protocols in the literature: the stiffness and the flexibility protocols, and determine if they produce the same data when testing porcine specimens in six degrees of freedom under the same testing conditions. In theory, the stiffness and the flexibility protocols should produce equivalent data, however, no detailed comparison study is available in the literature for the IVD, which is a very complex composite structure.

Tests were performed using the unique six axis simulator at the University of Bath on twelve porcine lumbar functional spinal unit (FSU) specimens at 0.1 Hz under 400 N preload. The specimens were divided in two groups of six and each group was tested using one of the two testing protocols. To ensure the same conditions were used, tests were firstly carried out using the stiffness protocol, and the equivalent loading amplitudes were then applied using the flexibility protocol.

The results from the two protocols were analysed to produce load-displacement graphs and stiffness matrices. The load-displacement graphs of the translational axes show that the stiffness protocol produces less spread between specimens than the flexibility protocol. However, for the rotational axes there is a large variability between specimens in both protocols. Additionally, a comparison was made between the six main diagonal terms of the stiffness matrices using the Mann-Whitney test, since the data was not normally distributed. No statistically significant difference was found between the stiffness terms produced by each protocol. However, overall the stiffness protocol generally produced larger stiffnesses and less variation between specimens.

This study has shown that when testing porcine FSU specimens at 0.1 Hz and 400 N preload, there is no statistically significant difference between the main diagonal stiffness terms produced by the stiffness and the flexibility protocols. This is an important result, because it means that at this specific testing condition, using the same testing parameters and environment, both the stiffness and flexibility methods can be used to characterise the behaviour of the spine, and the results can be compared across the two protocols. Future work should investigate if the same findings occur at other testing conditions.

INTRODUCTION

Deformation of modular acetabular press-fit shells is of much interest for surgeons and manufacturers. Initial fixation is achieved through press-fit between shell and acetabulum with the shell mechanically deforming upon insertion. Shell deformation may disrupt the assembly process of modular systems and may adversely affect integrity and durability of the components and tribology of the bearing. The aim of the study was to show shell deformation as a function of bone and shell stiffness.

Introduction

Trabecular bone transmits loads to the cortical shell and is therefore most active in bone remodeling. This remodeling alters trabecular material strength thereby changing the bending stiffness. Accounting for trabecular material heterogeneity has been shown to improve empirical-µFEM correlations by allowing for more realistic trabecular bending stiffness. In µFEMs to reduce computation time, region averaging is often used to scale image resolution. However, region averaging not only alters trabecular architecture, but inherently alters the CT-intensity of each trabeculae. The effect of CT-intensity variations on computationally derived apparent modulus (E_app) in heterogenous µFEMs has not been discussed. The objectives of this study were to compare trabecular E_app among i) hexahedral and tetrahedral µFEMs, ii) µFEMs generated from 32 µm, 64 µm, and 64 µm down-sampled from 32 µm µ-CT scans, and iii) µFEMs with homogeneous and heterogeneous tissue moduli.

Chronic back pain is the leading cause of disability worldwide, affecting millions of people. The source of pain is usually the intervertebral disc (IVD), thus there has been a growing interest in developing new improved implants such as disc replacements to treat the condition. However, to ensure the artificial devices being designed replicate the intact disc, the biomechanical behaviour of the IVD must be well understood (Adams and Dolan, 2005). The two most widely used testing procedures in the spinal industry to characterise the behaviour of the disc are the flexibility and the stiffness protocols (Stokes et al, 2002 and Panjabi et al, 1976).

For elastic specimens, the results produced by the flexibility and the stiffness protocols should in theory be identical. However, this does not hold true for inelastic specimens, such as the IVD. For this reason, the custom developed Spine Simulator (Holsgrove et al, 2014) at the University of Bath has been used to compare, in six degrees of freedom, the extent of the difference produced by these two testing protocols.

A biomechanical model of the IVD was tested, which consisted of two cylindrical nylon blocks attached together with a layer of nitrile rubber, representing respectively the vertebral bodies (VB) and the IVD. Two steel pins were inserted into the VB, spanning the thickness of the disc, to ensure the stiffness raise either side of the neutral zone was replicated by the model. Tests were performed at a frequency of 0.1 Hz using triangular wave cycles. The specimen was firstly subjected to the stiffness protocol, characterised by displacements of ±0.5 mm in anterior-posterior and lateral shear, ±0.35 mm in axial compression and ±1.5 deg in all rotational axes. The resulting loads were applied to the specimen when subjected to the flexibility protocol. In addition, the effect of a preload was studied by testing specimens with an axial compressive load of 250 N.

The stiffness matrix was calculated for each test and the main diagonal terms produced for the two protocols were compared using the Mann-Whitney test. Overall, results showed that there was a significant difference in the stiffness terms produced by the two protocols when tests were performed with (p ≤ 0.016) and without (p = 0.004) a preload. The only exception was found in the flexion-extension axis when the test was performed with a preload (p = 0.337). Additionally, differences were also recorded when comparing the shape and linearity of the load-displacement hysteresis curve (Figure 1) and the area enclosed by the curve.

This preliminary study has provided important information regarding the differences in the data produced by the flexibility and the stiffness protocols, it is therefore impractical to compare results produced using these two methods. To ensure that in the future results can be compared across laboratories, there is a need for a standardised testing procedure in the spinal industry.

For figures/tables, please contact authors directly.

Aim:

To investigate the clinical outcomes of elbows with post-traumatic stiffness treated by open surgical release.

Introduction:

The assumption that symmetric extension-flexion gaps improve the femoral condyle lift-off phenomenon and the patellofemoral joint congruity in total knee arthroplasty (TKA) is now widely accepted. For tease reasons, the balanced gap technique has been developed. However, the management of soft tissue balancing during surgery remains difficult and much is left to the surgeon's feel and experience. Furthermore, little is known about the differences of the soft-tissue stiffness (STS) of medial and lateral compartment in extension and flexion in the both cruciate ligaments sacrificed knee. It has a deep connection with the achievement of appropriate gaps operated according to the balanced gap technique. Therefore, the purpose of this study was to analyze the STS of individual compartment in vivo.

INTRODUCTION

Several clinical studies demonstrated long-term adjacent-level effects after implantation of spinal fusion devices[1]. These effects have been reported as adjacent joint degeneration and the development of new symptoms correlating with adjacent segment degeneration[2] and the trend has therefore gone to motion preservation devices; however, these effects have not been understood very well and have not been investigated thoroughly[3].

The aim of this study is to investigate the effect of varying the stiffness of spinal fusion devices on the adjacent vertebral levels. Disc forces, moments and facet joint forces were analyzed.

Aim

Over the last 15 years there has been a series of publications reporting the beneficial effects of elbow arthrolysis, with considerable variation in operative technique and post-operative management. Many advocate the use of passive stretching techniques in the early post-operative period if range of motion fails to improve satisfactorily. The purpose of this study was to assess our results of open elbow arthrolysis in patients who did not receive any passive stretching after discharge from hospital.

AM Open Cell porous Ti Structures were investigated for compressive strength, morphology (i.e. pore size, struts size and porosity), and wear resistance with the aim to improve design capability at support of implant manufacturing. Specimens were manufactured in Ti6Al4V using a SLM machine. Struts sizes had nominal diameters of 200µm or 100µm, pores had nominal diameters of 700µm, 1000µm or 1500µm. These dimensions were applied to three different open-cell geometrical configurations: one with unit-cells based on a regular cubic arrangement (Regular), one with a deformed cubic arrangement (Irregular), and one based on a fully random arrangement (Fully Random). Morphological analysis was performed by image analysis applied onto optical and SEM acquired pictures. The analyses estimated the maximum and minimum Feret pores diameter, and the latter was used as one of the key parameters to describe the interconnected network of pores intended for bone colonization. Outcome revealed the systematic oversizing of the actual struts diameter Vs designed diameter; by opposite min. Feret diameters of the pores resulted significantly smaller than nominal pore diameters, thus better fitting within the range of pores dimension acknowledged to favor the osseointegration. Consequently, the actual total porosity is also reduced. Many technologic factors are responsible for the morphologic differences design vs actual, among these the influence of melting pool dimension, the struts orientation during building and the layer thickness have a significant impact. Mechanical compression was performed on porous cylinder samples. Test revealed the Yield Strength and Stiffness are highly sensitive to the actual porosity. Deformation behavior follows densification phenomenon at lower porosity, whereas at higher porosity the Gibson-Ashby model fits for most of the structure tested. The relationship among load direction, struts alignment and the collapse behavior of the unit cell geometries are discussed. Stiffness of the porous structure is evaluated in both quasistatic and cyclic compression. Wear was investigated according to Taber test method. The abrasion resistance is measured by scratching a ceramic wheel against the different AM porous structures along a circular path. Metal debris eventually loss were quantified by gravimetric analysis at different number of cycles. Correlation among AM porous structure geometry, porosity and wear loss is discussed. All the tested structures showed a debris loss within the limit suggested by FDA for the porous coating in contact with the bone tissue. The actual AM porous Titanium unit cell geometry and features are a key design input. In combination with all the other design factors of a device they may result helpful in address the stress shielding and prevent metal debris release issues. The study underlines the importance of the research activity in AM to support Design for Additive Manufacturing (DFAM) capability. For any figures or tables, please contact authors directly