Introduction. Range of motion (ROM) simulation of the hip is useful to understand the maximum impingement free ROM in total hip arthroplasty (THA). In spite of a complex multi-directional movement of the hip in daily life, most of the previous reports have evaluated the ROM only in specific directions such as flexion-extension, abduction-adduction, and internal - external rotation at 0° or 90° of hip flexion. Therefore, we developed ROM simulation software (THA analyzer) to measure impingement free ROM in any positions of the hip. Recent designs of the hip implants give a wider ROM by increasing the head diameter and then, bone to bone impingement can be a ROM limit factor particularly in a combination of deep flexion, adduction and internal rotation of the hip. Therefore, the purpose of this study were to observe an individual variation in the pattern of the bone impingement ROM in normal hip bone models using this software, to classify the bone impingement ROM mapping types and to clarify the factors affecting the bone impingement type. Methods. The subjects were 15 normal hips of 15 patients. Three dimensional surface models of the pelvis and femur were reconstructed from Computer tomography (CT) images. We performed virtual hip implantation with the same center of rotation, femoral offset, and leg length as the original hips. Subsequently, we created the ROM mapping until bone impingement using THA analyzer. We measured the following factors influenced on the bone impingement map patterns; the neck shaft angle, the femoral offset, femoral anteversion, pelvic tilt, acetabular anteversion, sharp angle, and CE angle. These factors were compared between the two groups. Statistical analysis was performed with Mann-Whitney U test, and statistical significance was set at P<0.05. Results. According to the borderline of ROM at the flexion-internal rotation corner on the bone impingement map, the hips were classified into two groups; group-A showed more than 45° of the borderline slope at the flexion-internal rotation corner and the remaining hips were group-B. (Fig.1). There were 7 hips in group-A and 8 hips in group-B. Femoral offset was 36.8±2.2 mm in group-A and 30±2.7 mm in group-B. Femoral anteversion was 32±6.4° in-group A and 43 ±4.8° in group-B. There were statistically significant differences in the femoral offset and femoral anteversion between the groups. There were no significant differences in the other factors. Discussion. The results of this study showed various ROM map patterns even in normal hips and we classified them into two groups. An increased femoral offset or a decreased femoral anteversion revealed an early impinge in internal rotation. ROM until bone impingement is affected by the individual bone morphology. However, it is not easy to evaluate bony ROM in complex hip positions. THA analyzer shows the impingement position visually on the map and it is easy to understand the hip positions with reduced ROMs. Conclusion. There are two patterns on the bony ROM map in normal hips, and an early impinge in internal rotation occurred by increasing the femoral offset or decreasing the femoral anteversion. For figures/tables, please contact authors directly.

Primary Total Knee Arthroplasty (TKA) is considered to be one of the most successful orthopedic surgical interventions performed. Long-term results have been generally excellent, with 10–15 year survival rates as high as 90–95% reported, few complications, and reoperations occurring in approximately one percent of patients per year. One of the most important outcome measures of TKA is the range of motion. It has been demonstrated that a 67° of knee flexion is needed for the swing phase of the gait, 83° to climb stairs, 90° to descend stairs, and 93° to rise from chair. This is a prospective study of 50 patients who underwent Total Knee Arthroplasty at Dayanand Medical College & Hospital, Ludhiana between March 2008 & April 2009. Patients with a primary diagnosis of osteoarthritis, rheumatoid arthritis, or traumatic arthritis in which Natural Knee II implant (Zimmer) was used were included in the study. Absolute exclusion criteria were infection, sepsis, osteomyelitis, revision of a previous total knee replacement or deformities of the hip and spine. Preoperative demographic data, including sex, age at surgery, side affected, body mass index, primary diagnosis, tibio-femoral angle, knee score and functional score, and preoperative passive ROM were obtained. Patients underwent a medial parapatellar approach, with cement used to fix both the femoral and tibial components. Patellar resurfacing was not performed. Following surgery, patients underwent physical therapy at home or in a physiotherapy center, as appropriate. ROM and flexion were calculated at three and six months postoperatively. 54% of the patients were of age 60–75 years and 70% of them were females. 92% patients suffered from osteoarthritis. 80% patients had a BMI of <30 points. 63.46% patients had a preoperative knee flexion of <90°. The average preoperative knee flexion improved from 94.94° to 107.21° at 3 months and 112.12° at 6 months postoperatively (p-value=0.000056). The average preoperative knee flexion in patients with preoperative knee flexion <90°, 90°–110° and >110° changed from 88.33°-106.36°-108.73°, 102.67°-108.33°-114° and 120.50°-110°-117.50° at 3 months and 6 months respectively. The average preoperative knee score was 46.55 and functional score was 50.30, which improved to 95.62 (p-value=0.000015) and 75.60 (p-value=0.000213) respectively. Postoperative ROM is a function of many factors, with preoperative ROM being one of the most important. The knee ROM tends to regress towards a mean with excellent preoperative ROM loosing and poor preoperative ROM improving. Several factors related to surgical techniques have been found to be important. These include the tightness of the retained posterior cruciate ligament, the elevation of the joint line, increased patellar thickness, and a trapezoidal flexion gap. Vigorous rehabilitation after surgery appears useful, while continuous passive motion has not been found to be effective. Obesity and previous surgery are poor prognostic factors. In general, the clinical results of TKA were satisfactory in terms of pain relief and overall function. It was found that measurement of preoperative flexion gives the surgeon a good parameter for predicting flexion after arthroplasty

INTRODUCTION. Femur is one of the bones in humans that exhibit ethnic, racial, and gender difference. Several basic and clinical studies were conducted to explore these variations. Clinical anthropological studies have dealt with the compatibility of femoral prostheses and osteosythesis and materials with the femur. If there is a misalignment between the Total Knee Arthroplasy (TKA) femoral comportment installation position, Range of Motion (ROM) failure and several problems may arise. The aim of this study was to evaluate anterior bowing of the Japanese femur and to assess the adequacy of TKA femoral comportment installation position. METHODS. We analyzed 76 normal Japanese and 97 TKA patients. (June 2014-June 2015) The average age of the normal subjects was 62.0±20.90 (24–88) years old and the average of TKA subjects was 73.6±7.9 (53–89) years old. First we defined and measured the anterior curvature and the posterior condylar offset (PCO) in normal japanese femurs. Then in TKA patients we set the implant as same angle of the component. Third, we measured the post operative anterior curvature and PCO. Then calculated the anterior curvature difference and PCO differences and preformed statistical analysis with ROM. RESULTS SECTION. The average of anterior curvature in normal subjects was 7.87±6.60 degrees. Among 97 TKA patients, pre-operative anterior curvature was 7.58±0.16 degrees. Further, the angle of component which was set the post operatively was 7.32±0.25. The average of Anterior curvature difference and PCO differences had correlation with ROM. DISCUSSION. Gilbert reported that caucasian femurs are straight compared to asian femurs. Chinese and Japanese showed different anterior curvature because of different life style. The chalenges are when operating on different ethnic patients, Orthopedic Surgeons consider many factors. Previous studies yielded different suggestions for the ideal point of entry. We suggest difference between the curves of the femurs should be considered for TKA femoral comportment installation position. SIGNIFICANCE. 1)Our results gave an anatomical characteristics of Japanese femur. 2)These data will give clinical indication for TKA femoral comportment installation position

Introduction:. UKA allows replacement of a single compartment in patients who have isolated osteoarthritis. However, limited visualization of the surgical site and lack of patient-specific planning provides challenges in ensuring accurate alignment and placement of the prostheses. Robotic technology provides three-dimensional pre-op planning, intra-operative ligament balancing and haptic guidance of bone preparation to mitigate the risks inherent with current manual instrumentation. The aim of this study is to examine the clinical outcomes of a large series of robot-assisted UKA patients. Methods:. The results of 500 consecutive medial UKAs performed by a single surgeon with the use of a metal backed, cemented prosthesis installed with haptic robotic guidance. The average age of the patients at the time of the index procedure was 71.1 years (range was 40 to 93 years). The average height was 68 inches (range 58″–77″) and the average weight was 192.0 pounds (range 104–339 pounds). There were 309 males and 191 females. The follow-up ranges from 2 weeks to 44 months. Results:. Surgical Technique: The technique evolved from a one night stay with a tourniquet and a retinacular “T'd” arthrotomy, to a same day surgical procedure with a 2.5–3 inch straight medial arthrotomy that is muscle sparing and tourniquet free allowing all patients to go home the same day with only 2–3 weeks of formal physical therapy post op, less pain medication and a quicker return to their preoperative range of motion. Clinical Outcomes: All patients increased their ROM by 3–6 months postop. The return to preoperative ROM was seen by 6 weeks with an increased ROM of 5–10 degrees by 1 year. 6 out of 500 patients were converted to a TKA (1.2%). Two for deep infection (one had severe venous stasis disease preop), Three for medial pain despite stable, well aligned implants, and one who developed pain at around 6 weeks that had a large scar band that formed across the top of the tibial poly causing pain with weight bearing. Conclusion:. This evolved surgical technique along with the use of the sophisticated, patient-specific preoperative and intraoperative planning software combined with haptically guided bone resection allowed most patients, regardless of age, to have their procedure performed as an outpatient. This new technique can provide significant savings to the healthcare system in terms of costs of hospital days, costs of rehabilitation, costs in pain medication and quality of life in the acute post operative period with no increased risk of failure, loosening, malalignment, DVT, PE, infection, return to the OR, readmissions, or manipulation

Metal-on-metal (MOM) retrieval studies have demonstrated that CoCr bearings used in total hip arthroplasty (THA) and resurfacing (RSA) featured stripe wear damage on heads, likely created by rim impact with CoCr cups.^1-3 Such subluxation damage may release quantities of large CoCr particles that would provoke aggressive 3^rd-body wear. With RSA, the natural femoral neck reduces the head-neck ratio but avoids risk of metal-to-metal impingement (Fig. 1).⁴ For this study, twelve retrieved RSA were compared to 12 THA (Table 1), evaluating, (i) patterns of habitual wear, (ii) stripe-wear damage and (iii) 3^rd-body abrasive scratches. Considering RSA have head/neck ratios much lower than large-diameter THA, any impingement damage should be uniquely positioned on the heads.

Twelve RSA and THA retrievals were selected with respect to similar diameter range and vendors with follow-up ranging typically 1–6 years (Table 1). Patterns of habitual wear were mapped to determine position in vivo. Stripe damage was mapped at three sites: polar, equatorial and basal. Wear patterns were examined using SEM and white light interferometry (WLI). Graphical models characterized the complex geometry of the natural femoral neck in coronal and sagittal planes and provided RSA head-neck ratios.⁴

Normal area patterns of habitual wear were similar on RSA and THA bearings. The wear patterns showing cup rim-breakout proved larger for RSA cups than THA. Polar stripes presented in juxtaposition to the polar axis in both RSA and THA (Fig. 1). As anticipated, basal stripes on RSA occurred at steeper cup-impingement angles (CIA) than THA. The micro-topography of stripe damage was similar on both RSA and THA heads. Some scratches were illustrative of 3^rd-body wear featuring raised lips, punctuated terminuses, and crater-like depressions (Fig. 2).

Neck narrowing observed following RSA procedures may be a consequence of impingement and subluxation due to the small head-neck ratios. However, lacking a metal femoral neck, such RSA impingement would not result in metal debris being released. Nevertheless it has been suggested that cup-to-head impingement produced large CoCr particles and also cup “edge wear” as the head orbits the cup rim.⁴ Our study showed that impingement had occurred as evidenced by the polar stripes and 3^rd-body wear by large hard particles as evidenced by the wide scratches with raised lips. We can therefore agree with the prior study, that 2-body and 3rd-body wear mechanisms were present in both RSA and THA retrievals.

Introduction

Recent literature has shown that RSAs successfully improve pain and functionality, however variability in range of motion and high complication rates persist. Biomechanical studies suggest that tensioning of the deltoid, resulting from deltoid lengthening, improves range of motion by increasing the moment arm. This study aims to provide clinical significance for deltoid tensioning by comparing postoperative range of motion measurements with deltoid length for 93 patients.

Intraoperative range of motion (ROM) radiographs are routinely taken during scaphoidectomy and four corner fusion surgery (S4CF) at our institution. It is not known if intraoperative ROM predicts postoperative ROM. We hypothesize that patients with a greater intra-operativeROM would have an improved postoperative ROM at one year, but that this arc would be less than that achieved intra- operatively. We retrospectively reviewed 56 patients that had undergone S4CF at our institution in the past 10 years. Patients less than 18, those who underwent the procedure for reasons other than arthritis, those less than one year from surgery, and those that had since undergone wrist arthrodesis were excluded. Intraoperative ROM was measured from fluoroscopic images taken in flexion and extension at the time of surgery. Patients that met criteria were then invited to take part in a virtual assessment and their ROM was measured using a goniometer. T-tests were used to measure differences between intraoperative and postoperative ROM, Pearson Correlation was used to measure associations, and linear regression was conducted to assess whether intraoperative ROM predicts postoperative ROM. Nineteen patients, two of whom had bilateral surgery, agreed to participate. Mean age was 54 and 14 were male and 5 were male. In the majority, surgical indication was scapholunate advanced collapse; however, two of the participants had scaphoid nonunion advanced collapse. No difference was observed between intraoperative and postoperative flexion. On average there was an increase of seven degrees of extension and 12° arc of motion postoperatively with p values reaching significance Correlation between intr-operative and postoperative ROM did not reach statistical significance for flexion, extension, or arc of motion. There were no statistically significant correlations between intraoperative and postoperative ROM. Intraoperative ROM radiographs are not useful at predicting postoperative ROM. Postoperative extension and arc of motion did increase from that measured intraoperatively

Dislocation is one of the most common complications in total hip arthroplasty (THA) and is primarily driven by bony or prosthetic impingement. The aim of this study was two-fold. First, to develop a simulation that incorporates the functional position of the femur and pelvis and instantaneously determines range of motion (ROM) limits. Second, to assess the number of patients for whom their functional bony alignment escalates impingement risk. 468 patients underwent a preoperative THA planning protocol that included functional x-rays and a lower limb CT scan. The CT scan was segmented and landmarked, and the x-rays were measured for pelvic tilt, femoral rotation, and preoperative leg length discrepancy (LLD). All patients received 3D templating with the same implant combination (Depuy; Corail/Pinnacle). Implants were positioned according to standardised criteria. Each patient was simulated in a novel ROM simulation that instantaneously calculates bony and prosthetic impingement limits in functional movements. Simulated motions included flexion and standing-external rotation (ER). Each patient's ROM was simulated with their bones oriented in both functional and neutral positions. 13% patients suffered a ROM impingement for functional but not neutral extension-ER. As a result, 48% patients who failed the functional-ER simulation would not be detected without consideration of the functional bony alignment. 16% patients suffered a ROM impingement for functional but not neutral flexion. As a result, 65% patients who failed the flexion simulation would not be detected without consideration of the functional bony alignment. We have developed a ROM simulation for use with preoperative planning for THA surgery that can solve bony and prosthetic impingement limits instantaneously. The advantage of our ROM simulation over previous simulations is instantaneous impingement detection, not requiring implant geometries to be analysed prior to use, and addressing the functional position of both the femur and pelvis

Pathologies such as Scapho-Lunate Advanced Collapse (SLAC), Scaphoid Non-union Advanced Collapse (SNAC) and Kienbock's disease can lead to arthritis in the wrist. Depending on the articular surfaces that are involved, motion preserving surgical procedures can be performed. Proximal Row Carpectomy (PRC) and Four Corner Fusion (4CF) are tried and tested surgical options. However, prospective studies comparing the two methods looking at sufficient sample sizes are limited in the literature. The purpose of this study was to prospectively compare the early results of PRC vs 4CF performed in a single centre. Patients with wrist arthritis were prospectively enrolled (2015 to 2021) in a single centre in Vancouver, Canada. Thirty-six patients and a total of 39 wrists underwent either a PRC (n=18) or 4CF (n=21) according to pre-operative clinical, radiographical, and intra-operative assessment. Patient-Rated Wrist Evaluation (PRWE) scores were obtained preoperatively, as well as at six months and one year post operatively. Secondary outcomes were range of motion (ROM) of the wrist, grip strength, reoperation and complication rates. Statistical significance was set at p=0.05. Respectively for PRC and 4CF, the average PRWE scores at baseline were 61.64 (SD=19.62) and 63.67 (SD=20.85). There was significant improvement at the six-month mark to 38.81 (SD=22.95) (p=0.031) and 41.33 (SD=26.61) (p=0.007), then further improvement at the 12month mark to 33.11 (SD=23.42) (p=0.007) and 36.29 (SD=27.25) (p=0.002). There was no statistical difference between the two groups at any time point. Regarding ROM, statistical difference was seen in pronation for the PRC group at the 6month mark from an average of 72.18 deg to 61.56 deg and in flexion at the 12 month mark from 47.89 deg to 33.50 deg. All other parameters did not show statistically significant difference post operatively. For ROM of the 4CF group, only flexion at the 12month mark showed statistically significant change from an average of 48.81 deg to 38.03 deg. There was no statistical difference in pre-operative ROM between the two groups. One patient in the 4CF group required a revision for delayed union, and three patients ended up with ulnar sided wrist pain. Patients undergoing PRC and 4CF showed significant improvement in post operative PRWE scores, this reflects existing literature. For 4CF care must be taken to minimise ulnar sided wrist pain by relatively shortening the unar sided carpal column mass. ROM analysis showed that patients lost some wrist flexion ROM post-operatively at the 12month mark with both PRC and 4CF. However, other ROM parameters were unchanged

Analyzing shoulder kinematics is challenging as the shoulder is comprised of a complex group of multiple highly mobile joints. Unlike at the elbow or knee which has a primary flexion/extension axis, both primary shoulder joints (glenohumeral and scapulothoracic) have a large range of motion (ROM) in all three directions. As such, there are six degrees of freedom (DoF) in the shoulder joints (three translations and three rotations), and all these parameters need to be defined to fully describe shoulder motion. Despite the importance of glenohumeral and scapulothoracic coordination, it's the glenohumeral joint that is most studied in the shoulder. Additionally, the limited research on the scapulothoracic primarily focuses on planar motion such as abduction or flexion. However, more complex motions, such as internally rotating to the back, are rarely studied despite the importance for activities of daily living. A technique for analyzing shoulder kinematics which uses 4DCT has been developed and validated and will be used to conduct analysis. The objective of this study is to characterize glenohumeral and scapulothoracic motion during active internal rotation to the back, in a healthy young population, using a novel 4DCT approach. Eight male participants over 18 with a healthy shoulder ROM were recruited. For the dynamic scan, participants performed internal rotation to the back. For this motion, the hand starts on the abdomen and is moved around the torso up the back as far as possible, unconstrained to examine variability in motion pathway. Bone models were made from the dynamic scans and registered to neutral models, from a static scan, to calculate six DoF kinematics. The resultant kinematic pathways measured over the entire motion were used to calculate the ROM for each DoF. Results indicate that anterior tilting is the most important DoF of the scapula, the participants all followed similar paths with low variation. Conversely, it appears that protraction/retraction of the scapula is not as important for internally rotating to the back; not only was the ROM the lowest, but the pathways had the highest variation between participants. Regarding glenohumeral motion, internal rotation was by far the DoF with the highest ROM, but there was also high variation in the pathways. Summation of ROM values revealed an average glenohumeral to scapulothoracic ratio of 1.8:1, closely matching the common 2:1 ratio other studies have measured during abduction. Due to the unconstrained nature of the motion, the complex relationship between the glenohumeral and scapulothoracic joints leads to high variation in kinematic pathways. The shoulder has redundant degrees of freedom, the same end position can result from different joint angles and positions. Therefore, some individuals might rely more on scapular motion while others might utilize primarily humeral motion to achieve a specific movement. More analysis needs to be done to identify if any direct correlations can be drawn between scapulothoracic and glenohumeral DoF. Analyzing the kinematics of the glenohumeral and scapulothoracic joint throughout motion will further improve understanding of shoulder mechanics and future work plans to examine differences with age

Hip instability is one of the most common causes for total hip arthroplasty (THA) revision surgery. Studies have indicated that lumbar fusion (LF) surgery is a risk factor for hip dislocation. Instrumented spine fusion surgery decreases pelvic tilt, which might lead to an increase in hip motion to accommodate this postural change. To the best of our knowledge, spine-pelvis-hip kinematics during a dynamic activity in patients that previously had both a THA and LF have not been investigated. Furthermore, patients with a combined THA and LF tend to have greater disability. The purpose was to examine spine-pelvis-hip kinematics during a sit to stand task in patients that have had both THA and LF surgeries and compare it to a group of patients that had a THA with no history of spine surgery. The secondary purpose was to compare pain, physical function, and disability between these patients. This cross-sectional study recruited participants that had a combined THA and LF (n=10; 6 females, mean age 73 y) or had a THA only (n=11; 6 females, mean age 72 y). Spine, pelvis, and hip angles were measured using a TrakSTAR motion capture system sampled at 200 Hz. Sensors were mounted over the lateral thighs, base of the sacrum, and the spinous process of the third lumbar,12th thoracic, and ninth thoracic vertebrae. Participants completed 10 trials of a standardized sit-to-stand-to-sit task. Hip, pelvis, lower lumbar, upper lumbar, and lower thoracic sagittal joint angle range of motion (ROM) were calculated over the entire task. In addition, pain, physical function, and disability were measured with clinical outcomes: Hip Disability Osteoarthritis Outcome Score (pain and physical function), Oswestry Low Back Disability Questionnaire (disability), and Harris Hip Score (pain, physical function, motion). Physical function performance was measured using 6-Minute Walk Test, Stair Climb Test, and 30s Chair Test. Angle ROMs during the sit-to-stand-to-sit task and clinical outcomes were compared between THA+LF and THA groups using independent t-tests and effect sizes (d). The difference in hip ROM was approaching statistical significance (p=0.07). Specifically, the THA+LF group had less hip ROM during the sit-to-stand-to-sit task than the THA only group (mean difference=11.17, 95% confidence interval=-1.13 to 23.47), which represented a large effect size (d=0.83). There were no differences in ROM for pelvis (p=0.54, d=0.28) or spinal (p=0.14 to 0.97; d=0.02 to 0.65) angles between groups. The THA+LF group had worse clinical outcomes for all measures of pain, physical function, and disability (p=0.01 to 0.06), representing large effect sizes (d=0.89 to 2.70). Hip ROM was not greater in the THA+LF group, and thus this is unlikely a risk factor for hip dislocation during this specific sit-to-stand-to-sit task. Other functional tasks that demand greater excursions in the joints should be investigated. Furthermore, the lack of differences in spinal and pelvis ROM were likely due to the task and the THA+LF group had spinal fusions at different levels. Combined THA+LF results in worse clinical outcomes and additional rehabilitation is required for these patients

Cryocompression therapy is a non-invasive and non-pharmacological modality used in managing acute post-operative inflammation and pain. A prospective, randomised controlled trial (RCT) was undertaken to evaluate the effectiveness of a post-operative cryocompression protocol using the Game Ready™ (GR) device versus usual care on recovery following total knee arthroplasty (TKA). A single centre RCT was conducted with 70 TKAs (68 patients) randomised to a 2-week intervention period consisting of treatment with GR cryocompression (n=33, 33.3% males) or a usual care protocol of ice with static compression using tubigrip (n=35, 54.3% males). Knee range of movement (ROM) (flexion and extension), a visual analogue pain score (VAS) and limb circumference were documented at day 1, 2 and 14, as well as 6 and 12 weeks post-surgery. ROM was also recorded at day 90, while medication use and length of hospital stay were documented. Patient reported outcome measures (PROMs) including the KOOS and patient satisfaction questionnaire were employed. The GR group demonstrated 2.3° more (p=0.05) knee extension ROM overall, as well as 2. 8° more at day 1 (p=0.048), 3.8° at day 14 (p=0.007) and 5.4° at 3 months (p=0.017). There were no group differences (p>0.05) observed in pain (VAS), flexion ROM, limb circumference, opioid use or other PROMs. Across the full cohort, higher pain levels resulted in increased opioid intake (p=0.002), older patients used significantly less opioids (p<0.001) and males reported significantly less pain (VAS) than females (p=0.048). Using GR following TKA is a safe, non-invasive tool that can be used to aid in the post-operative recovery period. Patients using the GR cryocompression device gained significantly more extension ROM compared to the conventional ice with compression group, despite no other group differences

Currently, the consensus regarding subscapularis tendon repair during a reverse total shoulder arthroplasty (rTSA) is to do so if it is possible. Repair is thought to decrease the risk of dislocation and improve internal rotation but may also increase stiffness and improvement in internal rotation may be of subclinical benefit. Aim is to retrospectively evaluate the outcomes of rTSA, with or without a subscapularis tendon repair. We completed a retrospective review of 51 participants (25 without and 26 with subscapularis repair) who received rTSR by a single-surgeon using a single-implant. Three patient reported outcome measures (PROM) were assessed pre-operatively and post-operative at twelve months, as well as range of movement (ROM) and plain radiographs. Statistical analysis utilized unpaired t tests for parametric variables and Mann-Whitney U test for nonparametric variables. External Rotation ROM pre-operatively was the only variable with a significance difference (p=0.02) with the subscapularis tendon repaired group having a greater range. Pre- and post-operative abduction (p=0.72 & 0.58), forward flexion (p=0.67 & 0.34), ASES (p=0.0.06 & 0.78), Oxford (p=0.0.27 & 0.73) and post-operative external rotation (p=0.17). Greater external rotation ROM pre-operatively may be indicative of the ability to repair the subscapularis tendon intra-operatively. However, repair does not seem to improve clinical outcome at 12 months. There was no difference of the PROMs and AROMs between the subscapularis repaired and not repaired groups for any of the variables at the pre-operative or 12 month post operative with the exception of the external rotation ROM pre-operatively. We can conclude that from PROM or AROM perspective there is no difference if the tendon is repaired or not in a rTSR and indeed the patients without the repair may have improved outcomes at 12 months

The musculoskeletal (MSK) profiles of water polo players and other overhead athletes has been shown to relate to injury and throwing performance (TP). There have been no robust studies conducted on the MSK profiles and the variables affecting TP amongst female, adolescent, elite water polo players. A prospective quantitative cohort design was conducted amongst eighty-three female adolescent, elite water polo players (range 14–19 years). All participants filled out the Kerlan-Jobe Orthopaedic Clinic questionnaire, followed by a battery of screening tests aimed to identify possible MSK factors affecting TP. Pain provocation tests, range of motion (ROM), upward scapula rotation (USR), strength and pectoralis minor length measurements were all included. Participants also performed throwing speed (TS) and throwing accuracy (TA) tests. All the data collected were grouped together and analysed using SPSS 28.0. The condition for statistical significance was set as p <0.05. Multi-collinearity was tested for among variables to find out inter-variable correlations. Finally, a multiple regression analysis was performed. The mean KJOC score was 82.55 ± 14.96. 26.5% tested positive for at least one of the impingement tests. The MSK profile revealed decreased internal rotation ROM, increased external rotation ROM, a downwardly rotated scapula, weak external rotators, weak serratus anterior strength, strong lower trapezius and gluteus medius strength and a shorter pectoralis minor length all on the dominant side. Age, pectoralis minor length, upper trapezius and serratus anterior strength as well as upward scapula rotation were all positively correlated with TS, while sitting height, upper trapezius and serratus anterior strength and glenohumeral internal rotation ROM were positively correlated with TA. Multiple MSK parameters were found to be related to TS and TA in elite, adolescent water polo players

Scapular notching is a common problem following reverse shoulder arthroplasty (RSA). This is due to impingement between the humeral polyethylene cup and scapular neck in adduction and external rotation. Various glenoid component strategies have been described to combat scapular notching and enhance impingement-free range of motion (ROM). There is limited data available detailing optimal glenosphere position in RSA with an onlay configuration. The purpose of this study was to determine which glenosphere configurations would maximise impingement free ROM using an onlay RSA prosthesis. A three-dimensional (3D) computed tomography (CT) scan of a shoulder with Walch A1, Favard E0 glenoid morphology was segmented using validated software. An onlay RSA prosthesis was implanted and a computer model simulated external rotation and adduction motion of the virtual RSA prosthesis. Four glenosphere parameters were tested; diameter (36mm, 41mm), lateralization (0mm, 3mm, 6mm), inferior tilt (neutral, 5 degrees, 10 degrees), and inferior eccentric positioning (0.5mm, 1.5mm. 2.5mm, 3.5mm, 4.5mm). Eighty-four combinations were simulated. For each simulation, the humeral neck-shaft angle was 147 degrees and retroversion was 30 degrees. The largest increase in impingement-free range of motion resulted from increasing inferior eccentric positioning, gaining 15.0 degrees for external rotation and 18.8 degrees for adduction. Glenosphere lateralization increased external rotation motion by 13. 6 degrees and adduction by 4.3 degrees. Implanting larger diameter glenospheres increased external rotation and adduction by 9.4 and 10.1 degrees respectively. Glenosphere tilt had a negligible effect on impingement-free ROM. Maximizing inferior glenosphere eccentricity, lateralizing the glenosphere, and implanting larger glenosphere diameters improves impingement-free range of motion, in particular external rotation, of an onlay RSA prosthesis. Surgeons’ awareness of these trends can help optimize glenoid component position to maximise impingement-free ROM for RSA. Further studies are required to validate these findings in the context of scapulothoracic motion and soft tissue constraints

Introduction. The first VRAS TKA was performed in New Zealand in November 2020 using a Patient Specific Balanced Technique whereby VRAS enables very accurate collection of the bony anatomy and soft tissue envelope of the knee to plan and execute the optimal positioning for a balanced TKA. Method. The first 45 VRAS patients with idiopathic osteoarthritis of the knee was compared with 45 sequential patients who underwent the same TKA surgical technique using Brainlab 3 which the author has used exclusively in over 1500 patients. One and two year outcome data will be presented. Results. One year outcome dataVely Brainlab Significance Oxford 43.4 40.5 P=0.01 WOMAC 8.4 14.1P=0.02 Forgotten Joint Score 72.2 58.3 P=0.01 KOOS ADL91.3 85.8 P=0.04 Normal 83.3 74.2P =0.048 Activity Pain 8.6 18.4 P=0.009 ROM 127 124 P=0.01 Patient Satisfaction 98% 95% P=0.62 Operation again 100% 91% P=0.055 The two year data will be available for the ASM Conclusion: The one year outcome data shows a significantly better Oxford, WOMAC, Forgotten Joint score, KOOS ADL, Normal score and ROM scores and the activity pain is less compared to the authors extensive experience with Brainlab 3

Massive posterosuperior cuff tears (mRCT) retracted to the glenoid are surgically challenging and often associated with high retear rates. Primary repair is a less-favourable option and other salvage procedures such as SCR and tendon transfers are used. This study presents clinical and radiological outcomes of muscle advancement technique for repair of mRCT. Sixty-one patients (mean age 57±6, 77% males and 23% females) (66 shoulders) underwent all-arthroscopic rotator cuff repair that included supraspinatus and infraspinatus subperiosteal dissection off scapular bony fossae, lateral advancement of tendon laminae, and tension-free double-layer Lasso Loop repair to footprint. Pre-and post-operative range of motion (ROM), cuff strength, VAS, Constant, ASES, and UCLA scores were assessed. Radiologic assessment included modified Patte and Goutallier classifications. All patients had MRI at 6 months to evaluate healing and integrity of repair was assessed using Sugaya classification with Sugaya 4 and 5 considered retears. Advanced fatty degeneration (Goutallier 3-4) was present in 44% and 20% of supraspinatus and infraspinatus. Tendon retraction was to the level of or medial to glenoid in 22%, and just lateral in 66%. 50.8% mRCT extended to teres minor. Subscapularis was partially torn (Lafosse 1-3) in 46% and completely torn (Lafosse 4-5) in 20%. At mean follow-up (52.4 weeks), a significant increase in ROM, Relative Cuff Strength (from 57% to 90% compared to contralateral side), VAS (from 4 ±2.5 to 1±1.7), Constant (50±17.8 to 74 ±13.0), ASES (52 ±17.5 to 87 ±14.9), and UCLA (16± 4.9 to 30 ±4.9) scores were noted. There were six retears (10%), one failure due to P. acnes infection. 93% returned to pre-injury work and 89% of cases returned to pre-injury sport. Satisfaction rate was 96%. Muscle advancement technique for mRCT is a viable option with low retear rates, restoration of ROM, strength, and excellent functional outcomes

Abstract. Introduction. There is little literature exploring clinical outcomes of secondarily displaced proximal humerus fractures. The aim of this study was to assess the rate of secondary displacement in undisplaced proximal humeral fractures (PHF) and their clinical outcomes. Methods. This was a retrospective cohort study of undisplaced PHFs at Royal Derby Hospital, UK, between January 2018-December 2019. Radiographs were reviewed for displacement and classified according to Neer's classification. Displacement was defined as translation of fracture fragments by greater than 1cm or 20° of angulation. Patients with pathological, periprosthetic, bilateral, fracture dislocations and head-split fractures were excluded along with those without adequate radiological follow-up. Results. In total, 681 patients were treated with PHFs within the study period and out of those 155 were excluded as above. There were 385 undisplaced PHFs with mean age 70 years (range, 21–97years) and female to male ratio of 3.3:1. There were 88 isolated greater tuberosity fractures, 182 comminuted PHFs and 115 surgical neck fractures. Secondary displacement occurred in 33 patients (8.6%). Mean time to displacement was 14.8 days (range, 5–45days) with surgical intervention required in only 5 patients. In those managed nonoperatively, three had malunion and one had nonunion. No significant differences were noted in ROM between undisplaced and secondarily displaced PHFs. Conclusion. Undisplaced fractures are the most common type of PHF. Rate of secondary displacement is low at 8.6% and can occur up to 7 weeks after injury. Displacement can lead to surgery, but those managed conservatively maintain their ROM at final follow up

Aims. Distraction osteogenesis with intramedullary lengthening devices has undergone rapid development in the past decade with implant enhancement. In this first single-centre matched-pair analysis we focus on the comparison of treatment with the PRECICE and STRYDE intramedullary lengthening devices and aim to clarify any clinical and radiological differences. Methods. A single-centre 2:1 matched-pair retrospective analysis of 42 patients treated with the STRYDE and 82 patients treated with the PRECICE nail between May 2013 and November 2020 was conducted. Clinical and lengthening parameters were compared while focusing radiological assessment on osseous alterations related to the nail’s telescopic junction and locking bolts at four different stages. Results. Osteolysis next to the telescopic junction was observed in 31/48 segments (65%) lengthened with the STRYDE nail before implant removal compared to 1/91 segment (1%) in the PRECICE cohort. In the STRYDE cohort, osteolysis initially increased, but decreased or resolved in almost all lengthened segments (86%) after implant removal. Implant failure was observed in 9/48 STRYDE (19%) and in 8/92 PRECICE nails (9%). Breakage of the distal locking bolts was found in 5/48 STRYDE nails (10%) compared to none in the PRECICE cohort. Treatment-associated pain was generally recorded as mild and found in 30/48 patients (63%) and 39/92 (42%) in the STRYDE and PRECICE cohorts, respectively. Temporary range of motion (ROM) limitations under distraction were registered in 17/48 (35%) segments treated with the STRYDE and 35/92 segments (38%) treated with the PRECICE nail. Conclusion. Osteolysis and periosteal reaction, implant breakage, and pain during lengthening and consolidation is more likely in patients treated with the STRYDE nail compared to the PRECICE nail. Temporary ROM limitations during lengthening occurred independent of the applied device. Implant-related osseous alterations seem to remodel after implant removal. Cite this article: Bone Joint J 2023;105-B(1):88–96

Most studies comparing medial pivot to the posterior stabilised (PS) systems sacrifice the PCL. It is unknown whether retaining the PCL in the Medial Congruent (MC) system may provide further benefit compared to the more commonly used PS system. A retrospective review of a single-surgeon's registry data comparing 44 PS and 25 MC with PCL retained (MC-PCLR) TKAs was performed. Both groups had similar baseline demographics in terms of age, gender, body mass index, and American Society for Anaesthesiology score. There was no significant difference in their preoperative range of motion (ROM) (104º±20º vs. 102º±20º,p=0.80), Oxford Knee Score (OKS) (27±6 vs. 26±7,p=0.72), and Knee Society Scoring System (KS) Function Score (KS-FS) (52±24 vs. 56±24,p=0.62). The preoperative KS Knee Score (KS-KS) was significantly lower in the PS group (44±14 vs. 54 ± 18,p<0.05). At 3-months postoperation, the PS group had significantly better OKS (38±6 vs. 36±6,p=0.02) but similar ROM (111º±14º vs. 108º±12º,p=0.25), KS-FS (73±20 vs. 68±23, p=0.32) and KS-KS (87±10 vs. 86±9,p=0.26). At 12-months postoperation, both groups had similar ROM (115º±13º vs. 115º±11º,p=0.99), OKS (41±5 vs. 40±5,p=0.45), KS-FS (74±22vs.78±17,p=0.80), and KS-KS (89±10vs.89±11,p=0.75). There was statistically significant improvement in all parameters at 1-year postoperation (p<0.05). The PS group had significant improvement in all parameters from preoperation to 3-month postoperation (p<0.05), but not from 3-month to 1-year postoperation (p≥0.05). The MC-PCLR group continued to have significant improvement from 3-month to 1-year postoperation (p<0.05). The MC provides stability in the medial compartment while allowing a degree of freedom in the lateral compartment. Preserving the PCL when using MC may paradoxically cause an undesired additional restrain that slows the recovery process of the patients after TKA. In conclusion, compared to MC-PCLR, a PS TKA may expect significantly faster improvement at 3 months post operation, although they will achieve similar outcomes at 1-year post operation