Introduction. The biomechanical behavior of lumbar spine instrumentation is critical in understanding its efficacy and durability in clinical practice. In this study, we aim to compare the biomechanics of the lumbar spine instrumented with single-level posterior rod and screw systems employing two distinct screw designs: paddle screw versus conventional screw system. Method. A fully cadaveric-validated 3D ligamentous model of the lumbopelvic spine served as the foundation for our comparative biomechanical analysis. 1. To simulate instrumentation, the intact spine was modified at the L4L5 level, employing either paddle screws or standard pedicle screws (SPS). The implants were composed of Ti-6AL-4V. Fixation at the S1 ensured consistency across loading scenarios. Loading conditions included a 400-N compressive load combined with a 10 N.m pure bending moment at the level of L1, replicating physiological motions of flexion-extension, lateral bending and axial rotation. We extracted data across various scenarios, focusing on the segmental range of motion at both implanted and adjacent levels. Result. In the flexion of L4L5, the applied force ranged from -29.2 to 29.3 N in the paddle screw, while it ranged from -25 to 25 N in the PS system. Similarly, the extension of L4L5 ranged from -3.1 to 2.6 N in the paddle and ranged from -4.5 to 3.9 N in the SPS system. In terms of stress distributions on the screw, stress concentrations decreased in several cases in the paddle design compared to the SPS systems. Top of Form. Conclusion. The paddle screw enhanced the range of motion overall in both the upper adjacent segment (L3L4) and the lower adjacent segment (L5S1) compared to the conventional SPS system. The stability of the aimed segment was increased by 33% on average with the paddle screw compared to conventional PS. Increasing the stability of the host segment decreases the possibility of non-union and the rate of fusion failure . 2.

Currently, between 17% of patients undergoing surgery for adult spinal deformity experience severe instrumentation related problems such as screw pullout or proximal junctional failure necessitating revision surgery. Cables may be used to reinforce pedicle screw fixation as an additive measure or may provide less rigid fixation at the construct end levels in order to prevent junctional level problems. The purpose of this study is to provide insight into the maximum expected load during flexion in UHMWPE cable in constructs intended for correction of adult spine deformity (degenerative scoliosis) in the PoSTuRe first-in-man clinical trial. Following the concept of toppinoff, a new construct is proposed with screw/cable fixation of rods at the lower levels and standalone UHMWPE cables at the upper level (T11). A parametric FE model of the instrumented thoracolumbar spine, which has been previously validated, was used to represent the construct. Pedicle screws are modeled by assigning a rigid tie constraint between the rod and the lamina of the corresponding spinal level. Cables are modeled using linear elastic line elements, fixing the rod to the lamina medially at the cranial laminar end and laterally at the caudal laminar end. A Youngs modulus was assigned such that the stiffness of the line element was the same as that of the cable. An 8 Nm flexion moment was applied to the cranial endplate. The maximum value of the force in the wire (80 N) is found at the T11 (upper) level. At the other levels, forces in the cable are very small because most of the force is carried by the screw (T12) or because the wires are force shielded by the contralateral and adjacent level pedicle screws (L2, L3). The model provides first estimates of the forces that can be expected in the UHMWPE cables in constructs for kyphosis correction during movement. It is expected that this approach can help in defining the number of wires for optimal treatment

Background. Fracture of an osteoporotic vertebral body reduces vertebral stiffness and decompresses the nucleus in the adjacent intervertebral disc. This leads to high compressive stresses acting on the annulus and neural arch. Altered load-sharing at the fractured level may influence loading of neighbouring vertebrae, increasing the risk of a fracture ‘cascade’. Vertebroplasty has been shown to normalise load-bearing by fractured vertebrae but it may increase the risk of adjacent level fracture. The aim of this study was to determine the effects of fracture and subsequent vertebroplasty on the loading of neighbouring (non-augmented) vertebrae. Methods. Fourteen pairs of three-vertebra cadaver spine specimens (67-92 yr) were loaded to induce fracture. One of each pair underwent vertebroplasty with PMMA, the other with a resin (Cortoss). Specimens were then creep loaded at 1.0kN for 1hr. In 17 specimens where the upper or lower vertebra fractured, compressive stress distributions were measured in the disc between adjacent non-fractured vertebrae by pulling a pressure transducer through the disc whilst under 1.0kN load. These ‘stress profiles’ were obtained at each stage of the experiment (in flexion and extension) in order to quantify intradiscal pressure (IDP), the size of stress concentrations in the posterior annulus (SP) and compressive load-bearing by anterior (FA) and posterior (FP) halves of the vertebral body and by the neural arch (FN). Results. No differences were found between Cortoss and PMMA so all data were pooled. Following fracture, IDP fell by 26% in extension (P=0.004) and SP increased by more than 200% in flexion (P=0.01). FA decreased from 55% to 36% of the applied load in flexion (P=0.002) and from 36% to 27% in extension (P=0.002). FN increased from 17% to 31% in flexion (P=0.006) and from 22% to 37% in extension (P=0.008). Vertebroplasty reduced stress concentrations in the disc and restored load-bearing towards pre-fracture values. Conclusion. Vertebral fracture transfers compressive load from the anterior vertebral body to the posterior vertebral body and neural arch of adjacent (non-fractured) vertebrae. Vertebroplasty largely restores normal load-sharing at both the augmented and adjacent levels and in doing so may help reduce the risk of a spinal fracture cascade

Background. The controversy concerning the benefits of unisegmental cervical disc arthroplasty (CDA) over anterior cervical discectomy and fusion (ACDF) is still open because some randomised clinical trial (RTC) comparing ACDF with CDA have been highly inconclusive. Most of these studies mixed disc prosthesis with dissimilar kinematic characteristics. To date, a compilation of the clinical and radiologic outcomes and adverse events of anterior cervical discectomy and fusion (ACDF) compared with a single cervical disc arthroplasty (CDA) design, the Bryan disc has partially accomplished. Methods. This is a systematic review of RCTs with level I-II evidence. Only RCTs reporting clinical outcomes were included in this review. After a search on different databases including PubMed, Cochrane Central Register of Controlled Trials, and Ovid MEDLINE, a total of 10 RCTs out of total 51 studies were entered in the study. RTC's were searched from the earliest available records in 2005 to December 2014. Results. Five studies were Level I, and five were Level II. Out of a total of 1101 patients, 562 patients were randomly assigned into the Bryan arthroplasty group and the remaining 539 patients into the ACDF group. The mean follow-up was 30.9 months. Patients undergoing CDA had lower Neck Disability Index, and better SF-36 Physical component scores than ACDF patients. Patients with Bryan CDA had also less radiological degenerative changes at the upper adjacent level. Overall adverse events were twice more frequent in patients with ACDF. The rate of revision surgery including both adjacent and index level were slightly higher in patients with ACDF, showing no statistically significant difference. Conclusions. This review of evidence level I-II RCTs comparing clinical and radiological outcomes of patient undergoing Bryan arthroplasty or ACDF indicated a global superiority of the Bryan disc. The impact of both surgical techniques on the cervical spine (radiological spine deterioration and/or complications) was more severe in patients undergoing ACDF. However, the rate of revision surgeries at any cervical level was equivalent for ACDF and Bryan arthroplasty. These data suggest that even though the loss of motion has a determinant influence in the development of degenerative changes in ACDF cases, these kinematic factors do not imply a higher rate of symptomatic adjacent segment degeneration requiring surgery. Level of Evidence. Level I

Summary Statement. To evaluate carbon-fiber-reinforced PEEK as alternative biomaterial for total disc arthroplasty a closed loop between biotribology (in vitro), application of sterile particle suspensions in the epidural space of rabbits and biological response in vivo was established. Introduction. To prevent adjacent level degeneration in the cervical spine, total disc arthroplasty (TDA-C) remains an interesting surgical procedure for degenerative disc disease. Short- or midterm complications are migration, impaired post-operative neurological assessment due to artefacts in x-ray and MRI diagnosis and substantial rates of heterotopic ossification. The idea was to create a TDA-C design based on a polymer-on-polymer articulation to overcome these limitations of the clinically established metal-on-polyethylene designs. The objective of our study was to characterise the biotribological behaviour of an experimental cervical disc replacement made out of carbon-fiber-reinforced (CFR) PEEK and evaluate the biological response of particulate wear debris in the epidural space in vivo. Materials & Methods. In vitro wear simulation acc. to ISO 18192-1 was performed for 10 million cycles on a clinically established TDA-C device (Aesculap, Tuttlingen) made of cobalt-chromium-on-polyethylene in a direct comparison to an experimental disc prototype made of CFR-PEEK. An estimation of particle size and morphology was done acc. to Affatato et al. [5] and sterile suspensions of comparable particles (size 90% < 1 µm) in phospate buffered saline (PBS) were produced [6] for the application in the epidural space of 36 white new zealand rabbits. The particle concentration was 1 mg/ml with a volume of 0.2 ml injected percutaneously using fluoroscopic guidance and the inflammatory response was assessed 3 and 6 months post-operatively in a direct comparison between the groups PBS (control), UHMWPE and CFR-PEEK. Results. The gravimetric wear rate was for the cobalt-chromium-on-polyethylene TDA-C device as a clinical reference 1.0 ± 0.1 mg/ million cycles, compared to 0.02 ± 0.02 mg/ million cycles for the experimental CFR-PEEK articulation (p < 0.001), whereas the cumulative amount of wear of the CFR-PEEK TDA-C prototypes (0.5 ± 0.23 mg/ million cycles) was decreased by an order of a magnitude compared to cobalt-chromium-on-polyethylene (12.1 ± 1.46 mg/ million cycles) (p < 0.001). For CFR-PEEK and UHMWPE most of the particles were observed in a submicron size range and the morphology was comparable. Histopathological examination demonstrated wear debris in the vertebral canal of injection sites surrounded by inflammatory cells. The inflammation was limited to the epidural space around the particles and polymer particles were associated by a low grade foreign body reaction comprising macrophages and multi-nucleated giant cells. CFR-PEEK particulate wear debris showed at least similar histopathological reactions than UHMWPE in the cervical epidural space. Conclusion. A closed loop between biotribology (in vitro), application of sterile particle suspensions in the epidural space of rabbits and biological response in vivo was established to evaluate carbon-fiber-reinforced PEEK as alternative biomaterial for total disc arthroplasty

Long term, secondary implant fixation of Total Disc Replacements (TDR) can be enhanced by hydroxyapatite or similar osseo-conductive coatings. These coatings are routinely applied to metal substrates. The objective of this in vivo study was to investigate the early stability and subsequent bone response adjacent to an all polymer TDR implant over a period of six months in an animal model. Six skeletally mature male baboons (Papio annubis) were followed for a period of 6 months. Using a transperitoneal exposure, a custom-sized Cadisc L device was implanted into the disc space one level above the lumbo-sacral junction in all subjects. Radiographs of the lumbar spine were acquired prior to surgery, and post-operatively at intervals up to 6 months to assess implant stability. Flourochrome markers (which contain molecules that bind to mineralization fronts) were injected at specified intervals in order to investigate bone remodeling with time. Animals were humanely euthanized six months after index surgery. Test and control specimens were retrieved, fixed and subjected to histological processing to assess the bone-implant-bone interface. Fluorescence microscopy and confocal scanning laser microscopy were utilized with BioQuant image analysis to determine the bone mineral apposition rates and gross morphology. Radiographic evaluation revealed no loss of disc height at the operative level or adjacent levels. No evidence of subsidence or significant migration of the implant up to 6 months. Heterotopic ossification was observed to varying degrees at the operated level. Histology revealed the implant primary fixation features embedded within the adjacent vertebral endplates. Flourochrome distribution revealed active bone remodeling occurring adjacent to the polymeric end-plate with no evidence of adverse biological responses. Mineral apposition rates of between 0.7 and 1.7 microns / day are in keeping with literature values for hydroxyapatite coated implants in cancellous sites of various species. Radiographic assessment demonstrates that the Cadisc L implant remains stable in vivo with no evidence of subsidence or significant migration. Histological analysis suggests the primary fixation features are engaged, and in close apposition with the adjacent vertebral bone. Flourochrome markers provide evidence of a positive bone remodelling response in the presence of the implant

Vertebroplasty, which is the percutaneous injection of bone cement into vertebral bodies has recently been used to treat painful osteoporotic compression fractures. Early clinical results have been encouraging, but very little is known about the consequences of augmentation with cement for the adjacent, non-augmented level. We therefore measured the overall failure, strength and structural stiffness of paired osteoporotic two-vertebra functional spine units (FSUs). One FSU of each pair was augmented with polymethyl-methacrylate bone cement in the caudal vertebra, while the other served as an untreated control. Compared with the controls, the ultimate failure load for FSUs treated by injection of cement was lower. The geometric mean treated/untreated ratio of failure load was 0.81, with 95% confidence limits from 0.70 to 0.92, (p < 0.01). There was no significant difference in overall FSU stiffness. For treated FSUs, there was a trend towards lower failure loads with increased filling with cement (r. 2. = 0.262, p = 0.13). The current practice of maximum filling with cement to restore the stiffness and strength of a vertebral body may provoke fractures in adjacent, non-augmented vertebrae. Further investigation is required to determine an optimal protocol for augmentation

Objectives

We sought to determine if a durable bilayer implant composed of trabecular metal with autologous periosteum on top would be suitable to reconstitute large osteochondral defects. This design would allow for secure implant fixation, subsequent integration and remodeling.

In a study on ten fresh human cadavers we examined the change in the height of the intervertebral disc space, the angle of lordosis and the geometry of the facet joints after insertion of intervertebral total disc replacements. SB III Charité prostheses were inserted at L3-4, L4-5, and L5-S1. The changes studied were measured using computer navigation sofware applied to CT scans before and after instrumentation.

After disc replacement the mean lumbar disc height was doubled (p < 0.001). The mean angle of lordosis and the facet joint space increased by a statistically significant extent (p < 0.005 and p = 0.006, respectively). By contrast, the mean facet joint overlap was significantly reduced (p < 0.001). Our study indicates that the increase in the intervertebral disc height after disc replacement changes the geometry at the facet joints. This may have clinical relevance.