Poly-lactic acid (PLA) scaffolds are widely used in bone tissue engineering. The introduction of 3D printing has greatly increased the ability for tailoring different geometrical designs of these scaffolds for improved cellular attachment, growth and differentiation. This study aimed to investigate the effect of PLA fibre angle in 3D printed PLA scaffolds on hDPSC attachment and growth in vitro.

Two types of PLA scaffolds were prepared via 3D printing containing fibres angled at either 45° or 90°. hDPSCs (P4, 2*10⁵ cells per scaffold) were statically seeded for 4 hours on to the scaffolds (7×3.5×3 mm³, n=3). Cellular attachment was checked using fluorescence microscopy and the number of unattached cells was counted using a haemocytometer (HCM). The cell-scaffold constructs were then cultured in osteogenic medium for up to 5 weeks. ALP staining and SEM were performed for one construct from each group at week 3. Cellular viability was determined using CMFDA/EHD1 live/dead labelling at week 4. After 5 weeks, constructs were processed for histology.

Fluorescence micrographs showed high numbers of hDPSCs attached to scaffold surfaces in both groups after seeding irrespective of fibre angle. However, HCM cell count revealed that the 45° angled PLA scaffolds had significantly greater cell attachment compared to the 90° angled PLA group (p<0.0001). After 3 weeks in osteogenic culture, both types of construct showed strong ALP staining. SEM showed that in the 45° angled PLA group, almost all macro-pores were fully closed with newly formed cell sheets. In comparison, in the 90° angled group, most of the macro-pores remained open although a limited amount of cellular bridging was present. SEM also detected crystal deposits in different areas within the cell sheets for both construct groups. Most hDPSCs were alive in both groups at week 4 of culture with few dead cells present. After 5 weeks, histology showed marked cellular growth and new matrix formation, with detectable Van Kossa +ve crystal deposits in different areas within all constructs irrespective of PLA fibre angle.

This study showed that 45° angled PLA 3D printed scaffolds enhanced hDPSC attachment and cellular bridging, which may help to rapidly close the macro-pores within the scaffold compared to the 90° angled group. This illustrates the potential of 45° angled 3D printed PLA scaffolds as good candidates for bone tissue engineering.

Stromal cells derived from human dental pulp (HDPSCs) are of current interest for applications in skeletal tissue engineering. Angiogenesis and revascularization of bone grafts or bone constructs in vivo are of paramount importance for bone tissue regeneration and/or fracture healing. The aim of this study was to investigate the angiogenic and osteogenic potential of HDPSCs in combination with Bioglass¯ scaffolds in vitro and in vivo.

HDPSCs, isolated by collagenase digestion, were either maintained as monolayers or dynamically seeded on 3D Bioglass¯ scaffolds and cultured under either basal or osteogenic conditions for 2 and 4 weeks. Expression of osteogenic (COL1A1, ALP, RUNX2 and OC) and angiogenic markers (VEGFR2, CD34 and PECAM1) was determined using qRT-PCR. Alternatively, constructs were either cultured in vitro under basal/osteogenic conditions for 6 weeks or sealed in diffusion chambers which were then implanted intraperitoneally in immunosuppressed mice for 8 weeks. Retrieved constructs were fixed and embedded for histology and immunohistochemistry using antibodies against COL1, RUNX2, OC, VEGFR2, CD34 and PECAM1. qRT-PCR showed no significant differences in gene expression of osteogenic markers between basal and osteogenic media for both 3D construct and monolayers.

However when comparing 3D constructs to monolayers: COL1A1 showed a significantly lower expression (p< 0.05) in 3D compared to 2D at 2 weeks in both culture conditions, and this pattern was reversed after 4 weeks. ALPL was significantly lower in 3D constructs at 2 weeks under both conditions (p<0.01), and was significantly higher in basal conditions at 4 weeks (p<0.05). RUNX2 showed higher expression in 3D constructs at all time points and under both conditions while OC showed lower expression in 3D constructs at 2 weeks and higher expression at 4 weeks under both conditions. For the angiogenic markers, 3D constructs under osteogenic conditions showed an increase of expression in VEGFR2 and PECAM1 at 2 weeks followed by a decrease at week 4, while CD34 expression was undetected in 3D constructs at all times and under both sets of culture conditions. The expression of VEGFR2 and PECAM 1 under both conditions and at both time points was greater in 3D constructs compared to monolayers. After 8 weeks, the in vivo retrieved constructs showed no signs of inflammatory reactions. Immunohistology confirmed positive staining of osteogenic and angiogenic markers in 3D constructs from both in vitro and in vivo experiments with a greater staining intensity seen in the in vivo constructs. Furthermore, the in vivo constructs showed more intense sirius red staining and higher intensity of immunostaining using antibodies to type 1 collagen, with higher calcification as indicated by alizarin red staining.

In conclusion, this study indicated that a combination of HDPSCs and Bioglass¯ scaffolds has potential to provide a suitable microenvironment for angiogenic and osteogenic differentiation of HDPSCs which is essential for bone regeneration in preclinical and/or clinical applications.

Introduction

P-15 (GTPGPQGIAGQRGVV), a fifteen residue synthetic peptide, is a structural analogue of the cell binding domain of Type 1 collagen and creates a biomimetic environment for bone repair when immobilized on anorganic bovine mineral (ABM) scaffolds. ABM-P-15 scaffolds have been shown to enhance bone marrow stromal cell growth and differentiation. This study aimed at evaluating the osteogenic potential of human dental pulp stromal cells (HDPSCs) compared to human bone marrow stromal cells (HBMSCs) in monolayer and on 3D ABM-P-15 scaffolds in vitro and in vivo.