Introduction. Reverse total shoulder arthroplasty (RTSA) is rapidly being adopted as the standard procedure for a growing number of shoulder arthropathies. Though short-term outcomes are promising, mid- and long-term follow-ups present a number of complications – among them, humeral stem and glenosphere component loosening. Though not the primary complication, previously reported aseptic loosening required revision in 100% of cases. As the number of patients undergoing RTSA increases, especially in the younger population, it is important for surgeons to identify and utilize prostheses with stable long-term fixation. It has previously been shown in the hip and knee literature that implant migration in the first two years following surgery is predictive of later failure due to loosening in the 5=10-year postoperative window. The purpose of this study is to, for the first time, evaluate the pattern and total magnitude of implant migration in reverse shoulder arthroplasty using the gold standard imaging technique radiostereometric analysis (RSA). Methods. Forty patients were prospectively randomized to receive either a cemented or press-fit humeral stem, and a glenosphere secured to the glenoid with either autologous bone graft or 3D printed porous titanium for primary reverse total shoulder arthroplasty. Following surgery, participants are imaged using RSA, a calibrated, stereo x-ray technique. Radiographs are acquired at 6 weeks (baseline), 3 months, 6 months, 1 year, and 2 years. Migration of the humeral stem and glenosphere at each time point is compared to baseline. Migration of the prostheses is independently compared between humeral stem fixation groups and glenosphere fixation groups using a two-way repeated measures ANOVA with Tukey's test for multiple comparisons. Results. Follow-ups are ongoing and preliminary results are presented. Significant differences were observed at the 6-month and 1-year time points for superior-inferior translation (p = 0.0067, p = 0.0048), and total three-dimensional translation (p = 0.0011, p = 0.0272) between humeral stems, with press-fit humeral stems subsiding significantly more than cemented stems. Migration between the 6-month and 1-year time points was minimal for both stem fixation groups (less than 0.2 mm). No significant differences were observed along any axis at any time point for the glenosphere fixation groups. Conclusion. There is a trend towards increased subsidence with the use of press-fit stems compared to cemented stems in the first six months postoperatively, as is expected. Both implant fixation techniques demonstrate stability from six months through one year, and this trend is expected through two-year follow-up. Similarly, both glenosphere fixation techniques demonstrate immediate and stable fixation through one year

Abstract. Objectives. Stem malalignment in total hip arthroplasty (THA) has been associated with poor long-term outcomes and increased complications (e.g. periprosthetic femoral fractures). Our understanding of the biomechanical impact of stem alignment in cemented and uncemented THA is still limited. This study aimed to investigate the effect of stem fixation method, stem positioning, and compromised bone stock in THA. Methods. Validated FE models of cemented (C-stem – stainless steel) and uncemented (Corail – titanium) THA were developed to match corresponding experimental model datasets; concordance correlation agreement of 0.78 & 0.88 for cemented & uncemented respectively. Comparison of the aforementioned stems was carried out reflecting decisions made in the current clinical practice. FE models of the implant positioned in varus, valgus, and neutral alignment were then developed and altered to represent five different bone defects according to the Paprosky classification (Type I – Type IIIb). Strain was measured on the femur at 0mm (B1), 40mm (B2), and 80mm (B3) from the lesser trochanter. Results. Cemented constructs had lower strain on the implant neck, and higher overall stiffness and strain on bone compared to uncemented THA. Strain on the bone increased further down the shaft of the femoral diaphysis, and with progressing bone defect severity in all stem alignment cases. Highest strain on the femur was found at B2 in all stem alignment and bone defect models. Varus alignment showed higher overall femoral strain in both fixation methods. Interestingly, in uncemented models, highest strain was shown on femoral bone proximally (B1-B2) in varus alignment, but distally (B3) in neutral alignment. Conclusion. Varus stem alignment showed overall higher strain on femur compared to neutral and valgus. This highlights the crucial role of stem alignment in long term outcomes of THA. Differences between the two stem types should be taken in consideration when interpreting results from this study

Introduction. Porous metaphyseal cones are increasingly used for fixation in revision total knee arthroplasty (RTKA). Both cemented shorter length stems and longer diaphyseal engaging stems are currently utilized with metaphyseal cones with no clear evidence of superiority. The purpose of this study was to evaluate our experience with 3D printed titanium metaphyseal cones with both short cemented and longer cementless stems from a clinical and radiographic perspective. Methods. In total 136 3D printed titanium metaphyseal cones were implanted. The mean patient age was 63 and 48% were female. The mean BMI was 33 and the mean ASA class was 2.5. There were 42 femoral cones in which 28 cemented and 14 cementless stems were utilized. There were 94 tibial cones in which 67 cemented and 27 cementless stems were utilized. The choice for stem fixation was surgeon dependent and in general cones were utilized for AORI type 2 and 3 bone defects on the femur and tibia. The most common fixation scenario was short cemented stems on both the femur and tibia followed by cemented stem fixation on the tibia and cementless fixation on the femur. Clinical data such as revision, complication, and PRO was collected at last follow-up (minimum follow-up 1 year). Radiographic analysis included cone bony ingrowth and coronal and sagittal alignment on long-standing radiographs. Descriptive statistics were used to compare demographics between patients who had malalignment (HKA beyond +/− 3 degrees and flexion/extension beyond +/− 3 degrees). Adjusted logistic regression models were run to assess malalignment risk by stem type. Results. Patient reported outcomes demonstrated modest improvements with Pre-op KOOS improving from 44 pre-op to 59 post -op and PF-CAT improving from 33 to 37 post-op. PROMIS pain scores decreased significantly from 54 to 44 post-op. 36% of patients had malalignment in either the coronal or sagittal plane. Patients with malalignment were more likely to be female (66.7% vs 40.4%, p-value=0.02). After adjusting for age, sex and BMI, there was a significantly increased risk for coronal plane malalignment when both the femur and tibia had cementless compared to cemented stems (odds ratio=5.54, 95%CI=1.15, 26.80). There was no significantly increased risk when comparing patients with mixed stems to patients with cemented stems. Sagittal plane malalignment was more common with short cemented stems although both coronal plane and sagittal plane malalignment with either stem type was not associated with inferior clinical outcome. Overall cone survivorship was excellent with only two cones removed for infection. Conclusion. Metaphyseal titanium cones provide reliable fixation in revision TKA. However, PROs in this complex patient population show only modest improvement consistent with other variables such as co-morbidities and poor baseline physical function. Small cone inner diameter may adversely influence cementless stem position leading to coronal plane malalignment. Short cemented stems are subject to greater sagittal plane malalignment with no apparent influence on clinical outcome

Introduction. Femoral component loosening is one of the most common failure modes in cementless total hip arthroplasty (THA). Patient age, weight, gender, osteopenia, stem design and Dorr-C bone have all been proposed as risk factors for poor fixation and subsequent stem subsidence and poor outcome. With the increased popularity of CT-based assistive technologies in THA, (Stryker MAKO and Corin OPSTM), we sought to develop a technique to predicted femoral stem fixation using pre-operative CT. Methods. Fourteen patients requiring THA were randomly selected from a previous study investigating component alignment. Mean age was 64 (53 to 76), and 57% were female. All patients received pre-operative CT for 3D dynamic templating (OPSTM), and a TriFit stem and Trinity cup (Corin, UK) implanted through a posterior approach. Post-operatively, patients received an immediate CT and AP x-ray prior to leaving the hospital, and a 1-year follow-up x-ray. On both the immediate post-op x-ray and 1-year follow-up x-ray, the known cup diameter was used to scale the image. On both images, the distance between the most superior point of the greater trochanter and the shoulder of the stem was measured. The difference was recorded as stem subsidence. Subsidence greater than 4mm was deemed clinically relevant. The post-operative CT was used to determine the precise three-dimensional placement of the stem immediately after surgery by registering the known 3D implant geometry to the CT. For each patient, the achieved stem position from post-op CT was then virtually implanted back into the pre-operative OPSTM planning software. The software provides a colour map of the bone density at the stem/bone interface using the Hounsfield Units (HU) of each pixel of the CT [Fig. 1]. Blue represents low density bone transitioning through to green and then red (most dense). Results. Mean stem subsidence was 2.1mm (0.2mm to 11.1mm). Two patients had clinically relevant subsidence. The first stem in a 68M subsided 11.1mm. The second in a 58M subsided 5.0mm. Both density colour plots had significant areas of blue (low density bone) around the proximal portion of the stem, with minimal medium/high density fixation when compared to the stems with minimal subsidence. Discussion. Using the Hounsfield units of the CT scan as an indicator for bone density, we were able to predict poor implant fixation and subsequent subsidence in a taper wedge stem. This new technology might have pre-operative value in providing a more quantitative measure of fixation and resultant stem choice. For any figures or tables, please contact the authors directly

We report a prospective study of the use of intramedullary bone blocks to improve the fixation of a matt-finish femoral stem in Charnley low-friction arthroplasties. There were 379 patients (441 hips), but at a minimum follow-up of ten years there were 258 arthroplasties in 221 patients including some which had been revised. The mean age at surgery was 41 years (17 to 51) and the mean follow-up was 13.4 years (1 to 20 including the early revisions). Nine stems (3.5%) had been revised for aseptic loosening, but there were no stem fractures. Survivorship of stems was 99.2% at ten years and 94.35% at 15 and 20 years. We found that the patient’s gender, the position of the stem and the experience of the surgeon all influenced the outcome. Our findings suggest that using our method of stem fixation, follow-up of over 11 years was needed to reveal the effects of endosteal cavitation of the femur, and of over 13 years to assess any divergence between the clinical and the radiological outcomes of stem fixation

This study reports the results of hybrid stem fixation in difficult revision hip arthroplasties where proximal femoral bone stock loss was severe. Twenty-six revision arthroplasties (21 women and 5 men, aged from 58 to 86 years), were performed between 1998 and 2008. The indication for surgery was aseptic loosening. In all cases, stabilization of the stem presented problems because of severe proximal femoral bone stock loss (due to extensive periprosthetic osteolytic defects), or because of iatrogenic defects or surgical procedures (attempts to remove the stem and cement with fenestration or extended osteotomy). The average follow-up was 48 months (range 16 to 120). Primary stability is necessary for the successful definite fixation of a cementless implant by bone. When this was not possible (because of proximal cortical insufficiency), we used a modular distally cemented long stem, bypassing the area of bone defect for at least 6–7 cm. Proximally bone defects were grafted and osteotomy was closed with cerclage wires. Four stems (15%) had an asymptomatic subsidence (3 stems subsided less than 3–4 mm and 1 stem about 15mm). No stem was revised to date. Major complications did not occur. The mean Harris hip score improved from 32 points preoperatively to 82.3 points (at the most recent evaluation). Hybrid fixation offers the advantage of initial and secure stability of the cemented stem on the short term, until stabilization of the entire implant by bone occurs. Thus early subsidence and loosening is avoided and on the long term benefits of the cementless fixation are attained. Our results support the method of hybrid fixation in patients with severe femoral bone loss (and consequently problematic stabilization), when primary stability is needed

Introduction/purpose: Cementless femoral fixation in TKA varies regarding philosophy of design, materials, and surgical technique. This study evaluates autograft enhancement with AML (porocoated) stems. Impaction autograft (head reamings) enhances cortico-cancellous fit in canals of different geometry, preserves bone, decreases potential for stress shielding and seals the stem from wear particles. Materials/methods: Clinical/radiologic evaluation of 110 AML prostheses (proximal/extensive porous-coated) with 4- to 11-year (mean 6.9) follow-up was performed. Demographics included 68 females, 42 males, age 34–90 (mean 66). Diagnoses included OA (86), RA (16), other (8). Key surgical points included: 1) stem matching/sizing to proximal cortical contact; 2) head/neck reaming with acetabular graters; 3) autograft delivery (distal-lateral) prior to partial stem insertion and proximal-medial prior to prosthetic seating. Results: Femoral stem fixation was successful in 98%. Autograft fill was visualized radiographically within the first 6 weeks. Stem fit-fill ratios were .63 proximally and .73 distally, suggesting that most stems were stabilized via cortico-cancellous bone. The 2 fixation failures (1 stem fracture, 1 aseptic loosening) occurred in large males with undersized stems. Radiologic stability was noted in 95%. There were 6 cases of proximal osteolysis secondary to wear without distal extension, and no lucency > 2mm. Mean subsidence was.6mm. There were 10 acetabular failures secondary to wear/loosening and 1 traumatic neck fracture. There were no infections. Conclusion: The technique of impaction autograft using femoral head reamings is a biological (osteoinductive-osteoconductive), practical, and simple treatment method to accommodate and fill femoral canal voids frequently encountered in THA. Large, stiff stems (with distal fixation) can be avoided with less risk of technical problems and long-term bone loss secondary to stress shielding. The technique can be utilized, with variation, in any current cementless femoral stem

In order to improve the fixation of the stem in primary Charnley low-friction arthroplasty, the medullary canal was routinely closed off with a cancellous bone block. A prospective study of 611 consecutive arthroplasties were carried out between 1 and 5 1/2 years (average 2 years and 9 months) after operation. There were two cases of radiological loosening of the stem, both of which could have been avoided. Five other patients showed demarcation of the bone-cement junction at the calcar; two of these are considered to be "at risk" of loosening. There was no evidence of radiological loosening of the stem in 604 cases and the method is recommended for routine use in primary total hip arthroplasty

Aims

Porous metaphyseal cones can be used for fixation in revision total knee arthroplasty (rTKA) and complex TKAs. This metaphyseal fixation has led to some surgeons using shorter cemented stems instead of diaphyseal engaging cementless stems with a potential benefit of ease of obtaining proper alignment without being beholden to the diaphysis. The purpose of this study was to evaluate short term clinical and radiographic outcomes of a series of TKA cases performed using 3D-printed metaphyseal cones.

Aims

To achieve the functional benefits of the direct anterior (DA) approach and the fixation benefits of cemented replacement, this study combined the two techniques posing the following questions: does the limited access of the DA approach adversely affect the cement technique?; and does such a cementing technique reduce the incidence of cementless complications?

Purpose: The purpose of this work was to evaluate the quality of cemented humeral stem fixation. We analysed the incidence and influence of humeral lucent lines and loosening after implantation of a shoulder prosthesis as a function of aetiology (fracture versus scapular osteoarthritis) and glenoid status (total versus partial humeral prosthesis). Material and methods: This retrospective series included 1842 first-intention shoulder prostheses reviewed at mean five years (2–10). We selected patients whose initial diagnosis was fracture of the superior portion of the humerus (n=300) and centred osteoarthritis (n=767). All stems implanted for fracture were cemented. For osteoarthritis, there were 610 total prostheses and 157 simple humeral prostheses: 752 stems were cemented and 15 were implanted without cement. The Constant score and radiographic results (AP and lateral view at least) were noted. Results: For cemented stems, the incidence of radiographic lucent lines and loosening was significantly higher in fractures (40% and 10% respectively) than in centred osteoarthritis (14% and 1%). Lucency and loosening did not influence functional outcome in patients with centred osteoarthritis but had a significantly negative effect on final outcome in fractures. For fractures, the incidence of lucent lines was correlated with migration of the tubercles. For osteoarthritis, there was no difference between total and partial prostheses in terms of loosening, but the functional outcome was significantly better with total prostheses. Conclusion: Fixation of the humeral implant with cement remains the gold standard for shoulder prostheses implanted for centred osteoarthritis. However, cement fixation yields disappointing results for fractures: defective fixation of the humeral stem is correlated with migration of the tubercles. For osteoarthritis, there are not more lucent lines with a total prosthesis which provides the better functional results

The early revision rate in elective Total Hip Arthroplasty (THA) three years after surgery in elderly patients over 80 years is significantly lower for cemented stems in the German Arthroplasty Register (EPRD): cemented 3,1% (3.0 – 3.2) vs. uncemented 4.2% (4.1 – 4.3; p < 0.001). However, the mortality rate in elderly patients is elevated for cemented fixation. This study presents a detailed analysis of the influence of stem type and fixation on revision and mortality rate in this patient cohort.

Elective primary THA cases for primary Coxarthrosis using uncemented cups from the EPRD data base were analysed (n₀= 37,183). Four stem type groups were compared: cementless, cementless with collar, cementless short, and cemented. Stems with at least 300 cases at risk three years after surgery were analysed individually. The reference stem was determined as the stem with the lowest revision rate and at least 1000 cases under surveillance 3 years after surgery (n₃ = 28,637).

The revision rate for cemented stems (2.5% [2.2–1.81] was lower than for uncemented (4.5% [4.2–4.9]; p<0.001) and uncemented short stems (4.2% [3.1–5.7]; p=0.002). The revision rate of uncemented collared stems (2.3% [1.5–3.6]) was similar to cemented stems (p=0.89) and lower than for uncemented stems (p=0.02). One year mortality showed no sig. differences between the groups (p>0.17): cemented 3.2% [2.9–3.6], uncemented 3.4% [3.1–3.7], uncemented short 3.5% [2.5–4.9], uncemented collar 2.0% [1.2–3.2].

“Cementless” and “cementless short” stems should not be used in patients over 80 years due to the higher revision risk. If cementing should be avoided, “cementless collared” stems seem to be a good alternative combined with a tendency for a lower one year mortality rate.

The excellent long-term results for the first-generation Charnley stem may not apply to later versions with flanges. It seems possible that the early design functioned as a taper-slip system, as accepted in the Exeter prosthesis.

Comparison with the requirements for the alternative composite-beam system for the femoral component shows considerable differences that have important implications. These include design, surface finish, cementing technique and the interpretation of radiological signs of loosening.

A distinction should be made between the requirements for the successful use of the two different engineering systems.s

Introduction

The decreased bone mass or local osteoporosis at the proximal femur is often recognized in patients of rheumatoid arthritis (RA). In total hip arthroplasty (THA), the cancellous bone will be lost when rasping technique is applied for the preparation of stem insertion. In addition, cutting or elongation for contracted muscles around the hip joint can be required to insert the stem. To avoid these problems, the non-broaching, non-rasping impaction technique for the stems was applied in THA for the patients with RA. We report clinical and radiographic results of this method.

Background

The acknowledged benefit of the direct anterior (DA) approach is early functional return. Most surgeons in the U.S. use cementless femoral replacement given the negative track record of some cemented designs. However, delayed osseointegration of a femoral stem typically seen in older patients with poor bone quality will delay recovery, diminishing the benefits of the DA approach. Registry studies have shown a higher revision rate and complications in this patient population leading to a renewed interest in cemented fixation.

The calcar femorale is a vertical plate of bone lying deep to the lesser trochanter and is formed as a result of traction of the iliopsoas which separates the femoral cortex into two distinct layers, the calcar femorale and the medial femoral cortex. They fuse together proximally to form the medial femoral neck. A stem placed centrally will abut against the calcar femorale with little or no space for cement. Clearing of the calcar will offer space for a cement layer, which will support the stem proximally on the posterior aspect. We compared two consecutive groups of Charnley low-friction arthroplasties, with and without clearing of the calcar.

In 330 patients who had an arthroplasty without clearing the calcar, there were ten revisions for aseptic loosening of the stem and six other stems were considered ‘definitely loose’, giving a rate of failure of 4.8%. In 111 patients in whom the calcar was cleared there was only one revision for aseptic loosening and no stems were classed as ‘definitely loose’, giving a rate of failure of 0.9%.

Survivorship analysis has again shown the need for long-term follow-up; the differences became clear after ten years but because of the relatively small numbers, statistical analysis is not yet applicable.

We now clear the calcar femorale routinely and advocate optimal access to the medullary canal and insertion of the stem in the area of the piriform fossa.

A leading problem with cementless hip replacement is thigh pain, probably due to some degree of loosening. This is most pronounced during activities such as stair climbing or getting up from a chair. Our study compares the immediate fixation of three stems in widespread clinical use, using a cadaver test simulation in which the femur was horizontal, and cyclic forces acted vertically downward on the prosthetic head with gradual increments of load. We implanted and tested 18 pairs of femurs, making analyses between stem types by right to left comparisons. We found no statistically significant differences in loosening between cementless AML and PCA prostheses, but cemented stems withstood greater loads than uncemented stems by a factor of five or more.

Femoral stress shielding in cementless THA is a potential complication commonly observed in cementless distally loading press-fit stems. Long-term metaphyseal fixation and proximal load transfer is desired. Is routine autologous metaphyseal bone impaction and proximal primary stability an answer to this goal?

This prospective study describes long-term femoral bone remodeling and load transfer in cementless THA at a mean of 17 years (range: 15 to 20 years) in 208 consecutive fully HA-coated stems (Corail). All primary THA were performed by one group of surgeons between 1986 and 1991. The concept of surgical technique included impaction of autologous metaphyseal bone using bland femoral broaches until primary stability was achieved without distal press-fit.

Radiographic evaluation revealed a total of five (2.4%) stems with periprosthetic osteolysis, which were associated with eccentric polyethylene wear. They were either revised or awaiting revision. The remaining 97.6% stems revealed desired proximal load transfer in the metaphysis (52%) or in both metaphysis and diaphysis (48%). Distal stress shielding was not observed and was considered to be related to: impaction of metaphyseal bone, bland broaches, HA coating, and prosthetic design.

Biological autologous bone impaction of the metaphysis provides both primary stem stability and successful longterm osteointegration with the Corail stem after 20 years. The surgical technique of proximal autologous bone impaction rather than extraction of cancellous bone material and the use of a fully HA coated stem without distal press-fit show encouraging longterm results in THA.

Aims. To investigate the effect of polyethylene manufacturing characteristics and irradiation dose on the survival of cemented and reverse hybrid total hip arthroplasties (THAs). Methods. In this registry study, data from the National Joint Registry of England, Wales, Northern Ireland and the Isle of Man (NJR) were linked with manufacturing data supplied by manufacturers. The primary endpoint was revision of any component. Cox proportional hazard regression was a primary analytic approach adjusting for competing risk of death, patient characteristics, head composition, and stem fixation. Results. A total of 290,770 primary THAs were successfully linked with manufacturing characteristics. Overall 4,708 revisions were analyzed, 1,260 of which were due to aseptic loosening. Total radiation dose was identified as a risk factor and included in the Cox model. For statistical modelling of aseptic loosening, THAs were grouped into three categories: G1 (no radiation); G2 ( > 0 to < 5 Mrad); and G3 ( ≥ 5 Mrad). G1 had the worst survivorship. The Cox regression hazard ratio for revision due to aseptic loosening for G2 was 0.7 (95% confidence interval (CI) 0.58 to 0.83), and for G3 0.4 (95% CI 0.30 to 0.53). Male sex and uncemented stem fixation were associated with higher risk of revision and ceramic heads with lower risk. Conclusion. Polyethylene irradiation was associated with reduced risk of revision for aseptic loosening. Radiation doses of ≥ 5 Mrad were associated with a further reduction in risk. Cite this article: Bone Joint Res 2020;9(9):563–571

Aims. Osteoporosis can determine surgical strategy for total hip arthroplasty (THA), and perioperative fracture risk. The aims of this study were to use hip CT to measure femoral bone mineral density (BMD) using CT X-ray absorptiometry (CTXA), determine if systematic evaluation of preoperative femoral BMD with CTXA would improve identification of osteopenia and osteoporosis compared with available preoperative dual-energy X-ray absorptiometry (DXA) analysis, and determine if improved recognition of low BMD would affect the use of cemented stem fixation. Methods. Retrospective chart review of a single-surgeon database identified 78 patients with CTXA performed prior to robotic-assisted THA (raTHA) (Group 1). Group 1 was age- and sex-matched to 78 raTHAs that had a preoperative hip CT but did not have CTXA analysis (Group 2). Clinical demographics, femoral fixation method, CTXA, and DXA data were recorded. Demographic data were similar for both groups. Results. Preoperative femoral BMD was available for 100% of Group 1 patients (CTXA) and 43.6% of Group 2 patients (DXA). CTXA analysis for all Group 1 patients preoperatively identified 13 osteopenic and eight osteoporotic patients for whom there were no available preoperative DXA data. Cemented stem fixation was used with higher frequency in Group 1 versus Group 2 (28.2% vs 14.3%, respectively; p = 0.030), and in all cases where osteoporosis was diagnosed, irrespective of technique (DXA or CTXA). Conclusion. Preoperative hip CT scans which are routinely obtained prior to raTHA can determine bone health, and thus guide femoral fixation strategy. Systematic preoperative evaluation with CTXA resulted in increased recognition of osteopenia and osteoporosis, and contributed to increased use of cemented femoral fixation compared with routine clinical care; in this small study, however, it did not impact short-term periprosthetic fracture risk. Cite this article: Bone Joint J 2023;105-B(3):254–260

Aims. Revision total hip arthroplasty in patients with Vancouver type B3 fractures with Paprosky type IIIA, IIIB, and IV femoral defects are difficult to treat. One option for Paprovsky type IIIB and IV defects involves modular cementless, tapered, revision femoral components in conjunction with distal interlocking screws. The aim of this study was to analyze the rate of reoperations and complications and union of the fracture, subsidence of the stem, mortality, and the clinical outcomes in these patients. Methods. A total of 46 femoral components in patients with Vancouver B3 fractures (23 with Paprosky type IIIA, 19 with type IIIB, and four with type IV defects) in 46 patients were revised with a transfemoral approach using a modular, tapered, cementless revision Revitan curved femoral component with distal cone-in-cone fixation and prospectively followed for a mean of 48.8 months (SD 23.9; 24 to 112). The mean age of the patients was 80.4 years (66 to 100). Additional distal interlocking was also used in 23 fractures in which distal cone-in-cone fixation in the isthmus was < 3 cm. Results. One patient (2.2%) died during the first postoperative year. After six months, 43 patients (93.5%) had osseous, and three had fibrous consolidation of the fracture and the bony flap, 42 (91.3%) had bony ingrowth and four had stable fibrous fixation of the stem. No patient had radiolucency around the interlocking screws and no screw broke. One patient had non-progressive subsidence and two had a dislocation. The mean Harris Hip Score increased from of 57.8 points (SD 7.9) three months postoperatively to 76.1 points (SD 10.7) 24 months postoperatively. Conclusion. The 2° tapered, fluted revision femoral component with distal cone-in-cone-fixation, combined with additional distal interlocking in patients with bony deficiency at the isthmus, led to reproducibly good results in patients with a Vancouver B3 fracture and Paprosky type IIIA, IIIB, and IV defects with regard to union of the fracture, subsidence or loosening of the stem, and clinical outcomes. Cite this article: Bone Joint J 2024;106-B(4):344–351

Aims. This study evaluates risk factors influencing fracture characteristics for postoperative periprosthetic femoral fractures (PFFs) around cemented stems in total hip arthroplasty. Methods. Data were collected for PFF patients admitted to eight UK centres between 25 May 2006 and 1 March 2020. Radiographs were assessed for Unified Classification System (UCS) grade and AO/OTA type. Statistical comparisons investigated relationships by age, gender, and stem fixation philosophy (polished taper-slip (PTS) vs composite beam (CB)). The effect of multiple variables was estimated using multinomial logistic regression to estimate odds ratios (ORs) with 95% confidence intervals (CIs). Surgical treatment (revision vs fixation) was compared by UCS grade and AO/OTA type. Results. A total of 584 cases were included. Median age was 79.1 years (interquartile range 72.0 to 86.0), 312 (53.6%) patients were female, and 495 (85.1%) stems were PTS. The commonest UCS grade was type B1 (278, 47.6%). The most common AO/OTA type was spiral (352, 60.3%). Metaphyseal split fractures occurred only with PTS stems with an incidence of 10.1%. Male sex was associated with a five-fold reduction in odds of a type C fracture (OR 0.22 (95% CI 0.12 to 0.41); p < 0.001) compared to a type B fracture. CB stems were associated with significantly increased odds of transverse fracture (OR 9.51 (95% CI 3.72 to 24.34); p < 0.001) and wedge fracture (OR 3.72 (95% CI 1.16 to 11.95); p = 0.027) compared to PTS stems. Both UCS grade and AO/OTA type differed significantly (p < 0.001 and p = 0.001, respectively) between the revision and fixation groups but a similar proportion of B1 fractures underwent revision compared to fixation (45.3% vs 50.6%). Conclusion. The commonest fracture types are B1 and spiral fractures. PTS stems are exclusively associated with metaphyseal split fractures, but their incidence is low. Males have lower odds of UCS grade C fractures compared to females. CB stems have higher odds of bending type fractures (transverse and wedge) compared to PTS stems. There is considerable variation in practice when treating B1 fractures around cemented stems. Cite this article: Bone Jt Open 2021;2(7):466–475

Introduction. In the United States, cementless femoral fixation remains the dominant mode of fixation for femoral neck fractures, despite strong worldwide registry data that supports cemented fixation. The reason for this discrepancy remains unknown, controversial and often difficult to compare due to multiple variables. The purpose of this study was to evaluate a matched cohort of patients undergoing arthroplasty for femoral neck fractures and assess outcomes of revisions, periprosthetic fractures and mortality. Methods. This is an exact matched cohort study. Cemented fixation cases were exact matched to cementless fixation cases in a 1:1 fashion based on age, sex and Charlson Comorbidity Index (CCI). Outcome variables included: revision for periprosthetic fracture; all cause revision and mortality at any time point; all cause revision and mortality within 1-year and within 90-days. The primary independent variable was femoral fixation (cemented, cementless) and covariates included race (black, white, other), ethnicity (hispanic, non-hispanic), teaching status (minor, major, nonteaching) and bedsize (1–99, 100–399, >=400). Chi-square tests and multivariable logistic regression models were used for statistical analysis. Results. A total of 64,283 femoral neck fractures were evaluated. 17,138 cementless femoral stems were matched exactly to cemented femoral stems based on age, gender and Charleston comorbidity index (CCI). In the multivariate logistic regression analysis, compared to cementless femoral fixation, cemented fixation was associated with a 20% reduction in overall revision (OR 0.796, 0.675–0.939), a 30% reduction in revision at 1 year (OR: 0.709, 0.589–0.854) and a 86% reduction in revision for periprosthetic fracture (OR: 0.144, 0.07–0.294). However, cemented stem fixation was associated with a 23% (OR: 1.33, 1.134–1.338) and 16% (OR: 1.232, 1.134–1.338) increase in mortality at 90 days and 1 year post op respectively. Conclusions. In this exact matched cohort study, risk of early revision and revision for PPFx was dramatically reduced at all time points with the use of cemented stem fixation for elective THA and FNF. However, the increased risk of 90d and 1 year mortality following cemented stem fixation in the elective population warrants further investigation

Aims. The aim of this study was to describe the management and associated outcomes of patients sustaining a femoral hip periprosthetic fracture (PPF) in the UK population. Methods. This was a multicentre retrospective cohort study including adult patients who presented to 27 NHS hospitals with 539 new PPFs between 1 January 2018 and 31 December 2018. Data collected included: management strategy (operative and nonoperative), length of stay, discharge destination, and details of post-treatment outcomes (reoperation, readmission, and 30-day and 12-month mortality). Descriptive analysis by fracture type was performed, and predictors of PPF management and outcomes were assessed using mixed-effects logistic regression. Results. In all, 417 fractures (77%) were managed operatively and 122 (23%) conservatively. The median time to surgery was four days (interquartile range (IQR) 2 to 7). Of those undergoing surgery, 246 (59%) underwent revision and/or fixation and 169 (41%) fixation alone. The surgical strategy used differed by Unified Classification System for PPF type, with the highest rate of revision in B2/B3 fractures (both 77%, 176/228 and 24/31, respectively) and the highest rate of fixation alone in B1- (55/78; 71%) and C-type (49/65; 75%) fractures. Cemented stem fixation (odds ratio (OR) 2.66 (95% confidence interval (CI) 1.42 to 4.99); p = 0.002) and B2/B3 fracture type (OR 7.56 (95% CI 4.14 to 13.78); p < 0.001) were predictors of operative management. The median length of stay was 15 days (IQR 9 to 23), 12-month reoperation rate was 5.6% (n = 30), and 30-day readmission rate was 8.4% (n = 45). The 30-day and 12-month mortality rates were 5.2% (n = 28) and 21.0% (n = 113). Nonoperative treatment, older age, male sex, admission from residential or nursing care, and sustaining the PPF around a revision prosthesis were significant predictors of an increased 12-month mortality. Conclusion. Femoral hip PPFs have mortality, reoperation, and readmission rates comparable with hip fracture patients. However, they have a longer wait for surgery, and surgical treatment is more complex. There is a need to create a national framework for data collection for this heterogeneous group of patients in order to understand the outcomes of different approaches to treatment. Cite this article: Bone Joint J 2022;104-B(8):997–1008

The demand for revision total knee arthroplasty (TKA) has grown significantly in recent years. The two major fixation methods for stems in revision TKA include cemented and ‘hybrid’ fixation. We explore the optimal fixation method using data from recent, well-designed comparative studies. We performed a systematic review of comparative studies published within the last 10 years with a minimum follow-up of 24 months. To allow for missing data, a random-effects meta-analysis of all available cases was performed. The odds ratio (OR) for the relevant outcome was calculated with 95% confidence intervals. The effects of small studies were analyzed using a funnel plot, and asymmetry was assessed using Egger's test. The primary outcome measure was all-cause failure. Secondary outcome measures included all-cause revision, aseptic revision and radiographic failure. There was a significantly lower failure rate for hybrid stems when compared to cemented stems (p = 0.006) (OR 0.61, 95% CI 0.42-0.87). Heterogeneity was 4.3% and insignificant (p = 0.39). There was a trend toward superior hybrid performance for all other outcome measures including all-cause re-revision, aseptic re-revision and radiographic failure. Recent evidence suggests a significantly lower failure rate for hybrid stems in revision TKA. There is also a trend favoring the use of hybrid stems for all outcome variables assessed in this study. This is the first time a significant difference in outcome has been demonstrated through systematic review of these two modes of stem fixation. We therefore recommend the use, where possible, of hybrid stems in revision TKA

Introduction. Patients with FNF may be treated by either total hip arthroplasty (THA) or hemiarthroplasty (HA). Utilizing American Joint Replacement Registry (AJRR) data, we aimed to evaluate outcomes in FNF treatment. Methods. Medicare patients with FNF treated with HA or THA reported to the AJRR database from 2012–2019 and CMS claims data from 2012–2017 were analyzed in this retrospective cohort study. “Early” was defined as less than 90 days from index procedure. A logistic regression model, including index arthroplasty, age, sex, stem fixation method, hospital size. 1. , hospital teaching affiliation. 1. , and Charlson comorbidity index (CCI), was utilized to determine associations between index procedure and revision rates. Results. Of 75,333 FNF procedures analyzed, 82.2% had HA. 8.4% had cemented fixation. 36.9% had cementless fixation. Fixation was unknown for 41,225 (54.7%) patients. 90-day readmissions rates were 1.3% for both cohorts. Both the early revision rate (0.9% HA vs. 1.3% THA, p<0.0001) as well as the overall revision rate (1.5% HA vs. 2.3% THA, p<0.0001) were higher in the THA cohort. The three most common reasons for any revision were instability (26%), infection (21%), and periprosthetic fracture (15%). Higher rates of any revision were associated with cementless fixation (OR=1.37, 95% CI 1.20–1.57) and increased age (OR=0.96, 95% CI 0.96–0.97). THA and increased age were risk factors for early and any revision for instability. Cementless fixation, female sex, and decreased age were associated with lower revision rates for infection. Conclusion. The most common surgical treatment for FNF reported to the AJRR was cementless stem fixation and hemiarthroplasty. The higher revision rates for FNF treatment with THA warrant further investigation. The use of cemented femoral fixation in this patient population may be under-utilized. These data provide a benchmark of US practice for reference and comparison to other practices throughout US and the world

Aims. Metaphyseal cones with cemented stems are frequently used in revision total knee arthroplasty (TKA). However, if the diaphysis has been previously violated, the resultant sclerotic canal can impair cemented stem fixation, which is vital for bone ingrowth into the cone, and long-term fixation. We report the outcomes of our solution to this problem, in which impaction grafting and a cemented stem in the diaphysis is combined with an uncemented metaphyseal cone, for revision TKA in patients with severely compromised bone. Methods. A metaphyseal cone was combined with diaphyseal impaction grafting and cemented stems for 35 revision TKAs. There were two patients with follow-up of less than two years who were excluded, leaving 33 procedures in 32 patients in the study. The mean age of the patients at the time of revision TKA was 67 years (32 to 87); 20 (60%) were male. Patients had undergone a mean of four (1 to 13) previous knee arthroplasty procedures. The indications for revision were aseptic loosening (80%) and two-stage reimplantation for prosthetic joint infection (PJI; 20%). The mean follow-up was four years (2 to 11). Results. Survival free from revision of the cone/impaction grafting construct due to aseptic loosening was 100% at five years. Survival free from any revision of the construct and free from any reoperation were 92% and 73% at five years, respectively. A total of six patients (six TKAs, 17%) required a further revision, four for infection or wound issues, and two for periprosthetic fracture. Radiologically, one unrevised TKA had evidence of loosening which was asymptomatic. In all unrevised TKAs the impacted diaphyseal bone graft appeared to be incorporated radiologically. Conclusion. When presented with a sclerotic diaphysis and substantial metaphyseal bone loss, this technique combining diaphyseal impaction grafting with a metaphyseal cone provided near universal success in relation to implant fixation. Moreover, radiographs revealed incorporation of the bone graft and biological fixation of the cone. While long-term follow-up will be important, this technique provides an excellent option for the management of complex revision TKAs. Cite this article: Bone Joint J 2020;102-B(6 Supple A):116–122

Aims. BoneMaster is a thin electrochemically applied hydroxyapatite (HA) coating for orthopaedic implants that is quickly resorbed during osseointegration. Early stabilization is a surrogacy marker of good survival of femoral stems. The hypothesis of this study was that a BoneMaster coating yields a fast early and lasting fixation of stems. Methods. A total of 53 patients were randomized to be treated using Bi-Metric cementless femoral stems with either only a porous titanium plasma-sprayed coating (P group) or a porous titanium plasma-sprayed coating with an additional BoneMaster coating (PBM group). The patients were examined with radiostereometry until five years after surgery. Results. At three months, the mean total translation (TT) was 0.95 mm (95% confidence interval (CI) 0.68 to 1.22) in the P group and 0.57 mm (95% CI 0.31 to 0.83) in the PBM group (p = 0.047). From two to five years, the TT increased by a mean of 0.14 mm (95% CI 0.03 to 0.25) more in the P group than in the PBM group (p = 0.021). In osteopenic patients (n = 20), the mean TT after three months was 1.61 mm (95% CI 1.03 to 2.20) in the P group and 0.73 mm (95% CI 0.25 to 1.21) in the PBM group (p = 0.023). After 60 months, the mean TT in osteopenic patients was 1.87 mm (95% CI 1.24 to 2.50) in the P group and 0.82 mm (95% CI 0.30 to 1.33) in the PBM group (p = 0.011). Conclusion. There was less early and midterm migration of cementless stems with BoneMaster coating compared with those with only a porous titanium plasma-sprayed coating. Although a BoneMaster coating seems to be important for stem fixation, especially in osteopenic patients, further research is warranted. Cite this article: Bone Joint J 2022;104-B(6):647–656

Our previous work presented at BHS revealed a reduced risk of revision for all reasons in THAs using lipped (asymmetric) liners. Some audience members felt that this finding may be due to unaccounted confounders and the hip surgery community remains sceptical. A fully adjusted Cox model was built after exploratory Kaplan-Meier analyses. The following surgical approaches were included in the analysis: Posterior, Hardinge/anterolateral, Other. The variables included in the final Cox model included: Gender, liner asymmetry, age, head composition, stem fixation method, head diameter, indication for implantation and surgical approach. An additional analysis of the 3 most commonly used polyethylene liners with both a flat and asymmetric version was performed. In the fully adjusted Cox model, the use of a flat liner was associated with increased risk of revision for instability (HR: 1.79, 95%CI: 1.52–2.10) and increased risk of revision for all reasons (HR 1.195, 95%CI: 1.104 – 1.293) when compared to THAs utilising flat liners. This finding was upheld in the product specific analysis. When utilising flat liners, the Hardinge/anterolateral approach was associated with a reduced risk of revision for instability compared to the posterior approach (HR 0.56, 95%CI: 0.446 to 0.706). When an asymmetric liner was used, there was no significant difference in the risk of revision for instability between the Hardinge/anterolateral approach and the posterior approach (HR 0.838, 95%CI: 0.633 – 1.110). The use of polyethylene-based bearings gives the surgeon the option to use asymmetric liners. The reduced risk of revision in THAs with asymmetric liners was seen in the analysis of the complete dataset and in the product specific analysis. Our results demonstrate that the posterior approach, when used with asymmetric XLPE liners, is not associated with a higher risk of revision for instability as historical data suggested

Cemented total hip replacement (THR) provides excellent outcomes and is cost-effective. Polished taper-slip (PTS) stems demonstrate successful results and have overtaken traditional composite-beam (CB) stems. Recent reports indicate they are associated with a higher risk of postoperative periprosthetic femoral fracture (PFF) compared to CB stems. This study evaluates risk factors influencing fracture characteristics around PTS and CB cemented stems. Data were collected for 584 PFF patients admitted to eight UK centres from 25/05/2006-01/03/2020. Radiographs were assessed for Unified Classification System (UCS) grade and Arbeitsgemeinschaft für Osteosynthesefragen/Orthopaedic Trauma Association (AO/OTA) type. Statistical comparisons investigated relationships by age, gender, and stem fixation philosophy (PTS versus CB). The effect of multiple variables was estimated using multinomial logistic regression to estimate odds ratios (OR) with 95% confidence intervals (CI). Median (IQR) age was 79.1 (72.0–86.0) years, 312 (53.6%) patients were female, and 495 (85.1%) stems were PTS. The commonest UCS grade was type B1 (278, 47.6%). The commonest AO/OTA type was spiral (352, 60.3%). Metaphyseal-split fractures occurred only with PTS stems with an incidence of 10.1%. Male gender was associated with a five-fold reduction in odds of a type C fracture (OR 0.22, 95% CI 0.12 to 0.41, p<0.001) compared to a type B fracture. CB stems were associated with significantly increased odds of transverse fracture (OR 9.51, 95% CI 3.72 to 24.34, p <0.001) and wedge fracture (OR 3.72, 95% CI 1.16 to 11.95, p <0.05) compared to PTS stems. This is the largest study investigating PFF characteristics around cemented stems. The commonest fracture types are B1 and spiral fractures. PTS stems are exclusively associated with metaphyseal-split fractures, but their incidence is low. Males have lower odds of UCS grade C fractures compared to females. CB stems had higher odds of bending type fractures (transverse and wedge) compared to PTS stems. Biomechanical testing is needed for validation and investigation of modifiable factors which may reduce the risk of unstable fracture patterns requiring complex revision surgery over internal fixation

Aims. We have evaluated the survivorship, outcomes, and failures of an interlocking, reconstruction-mode stem-sideplate implant used to preserve the native hip joint and achieve proximal fixation when there is little residual femur during large endoprosthetic reconstruction of the distal femur. Methods. A total of 14 patients underwent primary or revision reconstruction of a large femoral defect with a short remaining proximal femur using an interlocking, reconstruction-mode stem-sideplate for fixation after oncological distal femoral and diaphyseal resections. The implant was attached to a standard endoprosthetic reconstruction system. The implant was attached to a standard endoprosthetic reconstruction system. None of the femoral revisions were amenable to standard cemented or uncemented stem fixation. Patient and disease characteristics, surgical history, final ambulatory status. ,. and Musculoskeletal Tumor Society (MSTS) score were recorded. The percentage of proximal femur remaining was calculated from follow-up radiographs. Results. All 14 at-risk native hip joints were preserved at a mean final follow-up of 6.0 years (SD 3.7), despite a short residual femur, often after proximal osteotomies through the lesser trochanter. Overall, 13 of 14 stems had long-term successful fixation. Eight patients required no reoperation. Three patients required reoperation due to implant-related issues, and three patients required reoperation for wound healing problems or infection. There were no dislocations or fractures. At final follow-up the mean MSTS score was 24.9 (SD 4.1). Nine patients required no ambulation aids, and only one had a Trendelenburg gait. Conclusion. This interlocking, reconstruction-mode stem-sideplate reliably preserves native hip joint anatomy and function after large femoral resection with a short remaining proximal femur, both in the primary and revision setting. This is particularly important for preventing or delaying total femoral arthroplasty in young patients after oncological reconstruction. Hip abductor strength and function could be maintained by this method, and the risk of dislocation eliminated. The success of this technique in this modest series should be verified in a larger collaborative study and will be of interest to revision surgeons and oncologists. Cite this article: Bone Joint J 2021;103-B(2):398–404

Aim. To assess the effect of the bearing surface and head size on the survival of total hip replacements with modern bearing surface combinations. Methods. We combined the NJR dataset with polyethylene manufacturing properties as supplied by the manufacturers to sub-divide polyethylene into conventional (PE) and highly crosslinked (XLPE). Cause specific and overall reasons for revisions were analysed using Kaplan-Meier and multi-variate Cox proportional hazard regression survival analyses. The bearing surface analysis was repeated in patients undergoing THR under the age of 55. Results. A total of 337,786 primary THR cases were included with an associated 5,618 revisions. Head size was grouped in <= 28mm (group A), 32mm (group B) and >=36mm (group C). A Cox regression model adjusted for age, gender, bearing combination and stem fixation was used to provide Hazard Ratios (HR). With Group C as reference, revision for all causes in Group A had a HR 1.07 (95%CI 0.99, 1.15) and in Group B HR 0.92 (0.86, 0.98). In patients <55y of age, with MoP as reference, Hazard Ratio for MoXLPE was 0.77 (0.59, 1.01), CoC 0.64 (0.52, 0.78), CoXLPE 0.61 (0.47, 0.78), CoP 0.50 (0.36, 0.70) and CMoXLPE 0.47 (0.30, 0.76). Conclusion. When combined with modern bearing combinations, the use of femoral heads of 36mm or larger was associated with a decreased cumulative incidence of revision for dislocation and an increased incidence of revision for aseptic loosening. In patients under the age of 55, CMoXLPE performed best at maximum follow up of 11 years

Aims. The goals of this study were to define the risk factors, characteristics, and chronology of fractures in 5417 revision total hip arthroplasties (THAs). . Patients and Methods. From our hospital’s prospectively collected database we identified all patients who had undergone a revision THA between 1969 and 2011 which involved the femoral stem. The patients’ medical records and radiographs were examined and the relevant data extracted. Post-operative periprosthetic fractures were classified using the Vancouver system. A total of 5417 revision THAs were identified. Results. There were 668 intra-operative fractures, giving an incidence of 12%. Fractures were three times more common with uncemented stems (19%) than with cemented stems (6%) (p <  0.001). The incidence of intra-operative femoral fracture varied by uncemented stem type: fully-coated (20%); proximally-coated (19%); modular fluted tapered (16%) (p < 0.05). Most fractures occurred during the insertion of the femoral component (35%). One-third involved the diaphysis and 26% were of the calcar: 69% were undisplaced. There were 281 post-operative fractures of the femur (20-year probability = 11%). There was no difference in risk for cemented and uncemented stems. Post-operative fractures were more common in men < 70 years (p = 0.02). Periprosthetic fractures occurred earlier after uncemented revision of the femoral component, but later after a cemented revision. The most common fracture type was a Vancouver B. 1. (31%). Of all post-operative fractures, 24% underwent open reduction and internal fixation and 15% revision arthroplasty. Conclusion. In revision THA, intra-operative fractures occurred three times more often with an uncemented stem. Many were undisplaced diaphyseal fractures treated with cerclage fixation. . While the risk of post-operative fracture is similar between uncemented and cemented components, they occur at notably different times depending on the type of stem fixation. . Take home message: In revision THA, intra-operative periprosthetic femoral fractures occur three times more often with uncemented stems. Many are non-displaced diaphyseal fractures treated with cerclage fixation. While postoperative fracture risks are equivalent between uncemented and cemented components, they occur at notably different time periods based on stem fixation type. Cite this article: Bone Joint J 2016;98-B:468–74

Instability after TKA can result from ligament imbalance, attenuation of soft tissues, or ligament disruption. Flexion instability has been reported after both CR and PS TKA. However, the clinical manifestations of flexion instability can be quite variable. Symptoms of flexion instability include pain and swelling after activity. Bracing occasionally can be helpful. Revision options to treat flexion instability include tibial insert exchange and revision to increase constraint. However, more favorable results have been reported using implants with varus-valgus constraint. Constrained mechanisms include a varus-valgus constrained PS post or hinge. The constrained post relies on the mechanical function of the post to provide stability which may deform or wear in-vivo leading to recurrent instability if used for a completely deficient collateral ligament. The hinge, which provides more rigid constraint, is indicated for collateral ligament deficiency. However, the additional constraint also results in greater bone-implant interface stresses, which may be mitigated by use of stem fixation to minimise risk of loosening

Introduction. Metaphyseal cones with cemented stems are frequently used in revision total knee arthroplasties (TKAs). However, if the diaphysis has been previously violated (as in revision of a failed stemmed implant), the resultant sclerotic canal can impair cemented stem fixation, which is vital for cone ingrowth and long-term fixation. We report the outcomes of our novel solution to this problem, in which impaction grafting and a cemented stem in the diaphysis was combined with an uncemented metaphyseal cone for revision TKAs with severely compromised bone. Methods. A metaphyseal cone was combined with diaphyseal impaction grafting and cemented stems in a novel fashion for 35 revision TKAs. Mean age at revision TKA was 70 years, with 63% being male. Patients had a mean of 4 prior knee arthroplasty procedures. Indications for the revision with this construct were aseptic loosening (80%) and two-stage re-implantation for periprosthetic infection (PJI; 20%). Mean follow-up was 3 years. Results. Survivorship free from revision of the cone/impaction grafting construct due to aseptic loosening was 100% at 5 years. Survivorships free from any revision of the cone/impaction grafting construct and free from any reoperation were 92% and 73% at 5 years, respectively. Six knees (17%) required a reoperation (4 for infection/wound issues and 2 for periprosthetic fractures). Radiographically, 97% of cones were ingrown (1 loose cone in setting of PJI). In all but one case, impacted diaphyseal bone graft appeared to have incorporated radiographically. Conclusions. When presented with a sclerotic diaphysis and substantial metaphyseal bone loss, this innovative technique combining diaphyseal impaction grafting with a metaphyseal cone provided near universal success in regards to implant fixation. Moreover, radiographs revealed incorporation of the bone graft, and ingrowth of the cones. While long-term follow-up is required, this novel technique provides an excellent option in the most difficult of revision TKAs. For figures, tables, or references, please contact authors directly

The most common classification of periprosthetic femoral fractures is the Vancouver classification. The classification has been validated by multiple centers. Fractures are distinguished by location, stability of the femoral component, and bone quality. Although postoperative and intraoperative fractures are classified using the same three regions, the treatment algorithm is slightly different. Type A fractures involve the greater and lesser trochanter. Fractures around the stem or just distal to the stem are Type B and subcategorised depending on stem stability and bone quality. Type C fractures are well distal to the stem and are treated independent of the stem with standard fixation techniques. The majority of fractures are either B1 (stable stem) or B2 (unstable stem). The stem is retained and ORIF of the fracture performed for B1 fractures. B2 and B3 fractures require stem revision with primary stem fixation distal to the fracture. Intraoperative fractures use the same A, B, C regions but are subtyped 1–3 as cortical perforations, nondisplaced, and displaced unstable fractures, respectively. With the exception of A1 intraoperative fractures all other intraoperative fractures require surgical treatment. A recent publication utilizing a New York state registry highlighted the patient risk of mortality associated with periprosthetic hip fractures. One month, 6 month and 1 year mortality was 3.2%, 3.8% and 9.7%, respectively. The mortality risk was lower for periprosthetic fractures treated with ORIF at 1 and 6 months compared to fractures requiring revision total hip

The objective of this study was to evaluate the short term clinical and radiological results of a new short stem hip implant. In 29 consecutive patients suffering from osteoarthritis with 33 affected hip joints, the clinical and radiological results of 33 cementless hip arthroplasties using a cementless implanted short stem prosthesis type Aida and a cementless cup type Ecofit were evaluated prospectively between October 2009 and June 2015 in two hospitals. The median age of patients at time of surgery was 55 years (range, 30–71 years), 23 male and 10 female patients were included in the study. The median clinical follow up was 24 months (range, 1.5–51 months), and the median radiological follow up was 12 months (range, 1–51 months). Two patients were lost to follow up and two patients had only one immediate postoperative x- ray. The Harris Hip Score improved from a median preoperative value of 53 to a median postoperative value of 93 at follow up. Radiological analysis showed that 19 stems (58%) showed stable bony ingrowth, five cases (15%) showed stable fibrous ingrowth. Four cases need further follow up for proper evaluation of stem fixation. The short term survival of this new short stem is very promising, and achieving the goals of standard hip arthroplasty

Introduction. The Vancouver Classification System presents a systematic approach to classification of periprosthetic fractures of the proximal femur (PFPFs) that has been validated in previous studies. However, with the introduction of tapered fluted stems and cable plates since the introduction of the Vancouver System, the connection between fracture class and the preferred method of treatment is often unclear. The present study was undertaken to identify fracture patterns surrounding contemporary femoral stems and the relationship between the current method of treatment and the Vancouver Class of the periprosthetic fracture. Methods. Three experienced joint surgeons collected plain radiographs (AP and lateral) and CT/MR scans (n=40) from 72 cases of Vancouver A or B periprosthetic fractures performed over the period 2016–2018. We identified the mode of primary stem fixation and the Vancouver grade of the fracture (A, B1, B2 or B3). Two independent investigators examined all imaging studies and the intraoperative records and recorded: (i) and the location and distribution of the fracture surfaces, and (ii) the presence of incomplete cortical fractures that had initiated within the femoral cortex without completing propagation and (iii) the method of operative treatment. These data were analyzed to examine the incidence of fractures within more than one femoral zone and differences in the fracture patterns corresponding to each Vancouver class. Results. One fifth (21%) of fractures were Type A with the remainder consisting predominantly of Type B2 (39%), with approximately equal proportions of Type B1 (22%) and B3 (18%) fractures. In almost half of Type B2 fractures (a loose femoral stem and a fracture adjacent to the prosthesis), fractures were also present within the metaphysis (ie. Type A+B). In the presence of a cementless femoral stem, fractures often occurred adjacent to the uncoated surface of the stem distal to the proximal ingrowth surface. Type B2 and B3 femurs had similar fracture patterns and degrees of comminution, though their method of treatment differed significantly. Incomplete fractures were identified in every Vancouver class (entire sample: 22%), especially in association with loose stems in poor quality bone (Type B3; 38% of cases). Conclusions. Approximately two-thirds of periprosthetic femoral fractures involve a loose femoral component (ie Types B2 and B3), though bone quality impacts operative treatment. In cementless stems, Vancouver Type B fractures often occur in the unbonded diaphysis between the distal edge of the ingrowth surface and immediately below the stem tip. Incomplete fractures are present in a surprising proportion of cases, suggesting that careful examination of imaging studies is needed to prevent fracture propagation due to inadequate fixation. CT scans are a useful adjunct to supplement plain radiographs. For any tables or figures, please contact the authors directly

INTRODUCTION. The Woodpecker pneumatic broaching system facilitates femoral preparation to achieve optimal primary fixation of the stem in direct anterior hip replacement using a standard operating table. The high-frequency axial impulses of the device reduce excess bone tension, intraoperative femoral fractures and overall operating time. The Woodpecker device provides uniformity and enhanced control while broaching, optimizing cortical contact between the femur and implant and thereby maximizing prosthetic axial stability and longevity. This study aims to describe a single surgeon's experience using the Woodpecker pneumatic broaching system in 649 cases of direct anterior approach (DAA) total hip arthroplasties to determine the device's safety and efficacy. METHODOLOGY. All consecutive patients undergoing elective anterior bikini total hip arthroplasties (THA) performed by a single surgeon between July 2013 and June 2018 were included. Patients undergoing a THA with the use of the Woodpecker device through a different surgical approach, revision THA or arthroplasties for a fractured neck of femur were excluded (n=219). The pneumatic device was used for broaching the femoral canal in all cases. Pre-operative and post-operative Harris Hip Scores (HHS) and post-operative radiographs were analyzed to identify femoral fractures and femoral component positioning at 6 weeks, 6 months and 12 months post-operative. Any intra-operative or post-operative surgical complications and component survivorship until most recent follow up were recorded in the clinical notes. RESULTS. A total of 649 patients (L THA=317, R THA=328 and bilateral=2) with a mean age of 69 (range 46–91yrs) and mean BMI of 28.3 (range = 18.4–44.0) underwent a DAA THA using a Woodpecker device were included in the study. Of these patients, 521 (80%) underwent uncemented and 128 (20%) underwent cemented femoral components. The time taken to broach the femur using Woodpecker broaching this system averaged 2.8 minutes (1.4 to 7.5 minutes) in both cemented and uncemented cases. In 91% of cases the templated broach size was achieved with the remaining 9% within +/− 1 size of the planned template. Radiographic analysis revealed 67.3% of the stems placed in 0–1.82 degrees of varus and 32.7% placed in 0–1.4 degrees of valgus. Average HHS were 24.4 pre-operatively, with drastic improvements shown at 6 weeks (80.95), 6 months (91.91) and 12 months (94.18) after surgery. Intraoperative femoral fractures occurred in three patients (0.4%) during trial reduction, a further three patients had periprosthetic post-operative fractures (0.4%) from falls, two patients had stem subsidence (0.3%) and a further two patients had wound infections (0.3%). At the most recent follow up, the survivorship of the acetabular component was 99.7% and the femoral component was 99.1%, with mean follow up of 2.9 years (0.5 to 5 years). No intraoperative or post-operative complications could be directly attributed to the Woodpecker broaching system. CONCLUSION. The pneumatic Woodpecker device is a safe and effective alternative tool in minimally invasive direct anterior hip replacement surgery for femoral broaching performed on a standard operating table. The skill and experience of the surgeon must be taken into consideration when utilizing new surgical devices

Aim. The objective of this study was to evaluate the intermediate term clinical and radiological results of a new short stem hip implant. Methods. In 20 consecutive patients suffering from osteoarthritis with 25 affected hip joints (five cases were bilateral), the clinical and radiological results of 25 hip arthroplasties performed in one hospital between October 2009 and May 2014 through a minimally invasive anterolateral approach using a cementless short stem prosthesis type Aida and a cementless cup type Ecofit with a ceramic on ceramic pairing were evaluated prospectively. The median age of patients at time of surgery was 60 years (range, 42–71 years), 15 male (4 were bilateral) and 5 female patients (one was bilateral) were included in the study. The median clinical follow up was 30 months (range, 2–88 months), and the median radiological follow up was 30 months (range, 2–88 months). Results. Harris Hip Score improved from a median preoperative value of 53 to a median postoperative value of 96 (range, 73–100) at follow up. 22 hips (88%) showed an excellent postoperative Harris Hip Score, 2 hips (8%) a good postoperative Harris Hip Score, and one hip (4%) a fair postoperative Harris Hip Score. Only two patients complained of postoperative thigh pain. Regarding patient satisfaction, 15 patients (60%) were very satisfied, 10 patients (40%) were satisfied. None was unsatisfied. Radiological analysis showed that 19 stems (76%) were with stable bony ingrowth, two cases (8%) showed stable fibrous ingrowth. Four cases need further follow up for proper evaluation of stem fixation.(See Figures 1,2,3). Conclusion. The intermediate term survival of this new short stem is very promising, and achieving the goals of a standard hip arthroplasty. For any figures or tables, please contact the authors directly

Background. Antibiotic loaded bone cement (ALBC) is commonly used in cemented total hip arthroplasty (THA) in an attempt to reduce the risk of prosthetic joint infection (PJI). However, its role versus plain cement remains controversial due to the potential risk of developing resistant organisms and potential excess costs incurred from its usage. We investigated the relationship of ALBC and plain cement in affecting outcome of revision surgery after primary THA. Methodology. We conducted a retrospective study of data collected from National Joint Registry for England and Wales, Northern Ireland and the Isle of Man between 1. st. September 2005 until 31. st. August 2017. A logistic regression analysis model was used to investigate the association between ALBC versus plain cement and the odds ratio (OR) for revision, adjusting for age, ASA grade, bearing surfaces, head size and cup and stem fixation. Indications for revision recorded in NJR were considered in separate models. Results. We identified 418,925 THAs where bone cements were used (22,037 plain cement; 396,888 ALBC). After adjusting for confounding factors, the risk of revision for infection was lower with ALBC (OR 0.77, 95% CI 0.62–0.95). There was also lower risk of revision for aseptic loosening of stem (OR 0.53, 95% CI 0.39–0.72), aseptic loosening of socket (OR 0.46, 95% CI 0.37– 0.58). When breaking down hips into fully cemented or hybrid fixation, the protective effect of ALBC against infection was only apparent in fully cemented (OR 0.65, 95% CI 0.48–0.87) when compared against hybrid fixation (OR 0.90, 95% CI 0.66–1.23). Discussion. Within the limits of registry analysis, this study has demonstrated an association between the use of ALBC and lower rates of revision for infection and aseptic loosening. Conclusion. This finding supports the current use of ABLC in cemented THAs

Background:. For hip prostheses, short stems allow easy insertion and reduce thigh pain risk, and are therefore suitable for Minimally Invasive Surgery. However, clinical outcome depends on sufficient initial fixation in the proximal femoral component. Revelation stems are designed to increase medullary cavity occupancy in the proximal femoral component and allow physiological load transmission within this component. Theoretically, on initial fixation of the proximal part of the stem, fixation remains unaffected by cutting the distal part of the stem. Recently, the Revelation micro MAX stem has become available. In this system, only the distal part of the stem is removed. To prepare for the introduction of this stem, we evaluated its rotational stability by installing it in the femurs of formalin-fixed cadavers. We then evaluated the time course of changes in bone density at the stem circumference and stem position by CT in the first eight patients undergoing hip arthroplasty. Subjects and Methods:. Micro MAX stems were inserted into the left femurs of one male and six female cadavers (76 to 95 years of age). A commonly used torque meter was mounted on the stem, and stem fixation was evaluated by the application of clockwise torque of 6 to 12 N-m. Further, in patients, three men and five women (age range 38–83 years, mean 67 years; two cases of femoral head necrosis, two of femoral neck fracture, and four of osteoarthritis of the hip) who underwent surgery with the micro MAX stem from July 2012 to April 2013 were evaluated at 3 weeks, and 3 and 6 months after surgery for stem insertion angle and stem subsidence by CT, and for bone density around the stem by the DEXE method. Results:. Rotational stability of the micro MAX stem in cadaveric femurs was similar to that of the conventionally used Revelation stem. In CT examination after surgery, the micro MAX stem tended to be inserted in a slightly varus position. No evidence of stem subsidence was observed in eight patients, but progression of the varus was seen in one. Bone density in the stem circumference was maintained. Discussion:. Although short stems have a number of advantages, problems with the first fixation might result in loosening. Allowing for the small number of patients and limited range of clinical conditions, our findings suggest that the rotational stability of the micro MAX stem is similar to that of the conventional stem. Postoperative CT measurement indicated that the micro MAX stem tended to be inserted in the varus position, particularly in patients with a large medullary cavity. The micro MAX stem was stable, and no decrease in bone density was seen. As with other short stems, however, care is required to avoid insertion in the varus position in patients with a large medullary cavity. Conclusion:. This investigation identified no problems in initial fixation with the micro MAX stem. Clinical outcomes with this system should be favorable

In contrast to the acetabular cup where the close to spherical shape of the implant allows a precise alignment and positioning, the femoral stem implant positioning has always been a compromise between anteversion, angulation and length of the prosthetic femoral neck and the congruence of the implant shaft with the inner anatomical shape of the proximal femur. Balancing these reduces the risks of dislocation and eccentric wear of the acetabular implant and of unfeasible loading of the femoral implant with loosening. Nevertheless neither the anchorage of the stem nor the alignment of the neck can ever be ideal as it would too much jeopardize the other aspect even if cement is used for stem fixation. Customary stem navigation only guides this compromise more precisely than eye balling. With the introduction of modular necks it has become possible to infringe this restrictive fix relation and after fully fitting stem fixation the neck alignment and length is optimized separately. With regard to computer assisted navigation the guidance takes into consideration the definitive stem position after best anatomical fixation. A sound navigation of cemented stems becomes also possible and brings up the opportunity to choose cementing or uncemented fixation based on whether the bone quality needs reinforcement by cement to get closer to the implant e-module or the bone promises to strengthen on its own on the same purpose

Longevity of the implants is the most respected factor in THA. Except from this fact, complications like dislocation, wear and osteolysis are reported in literature most frequently. But there is an underestimation in the orthopedic community in the importance of joint function, which is directly related to accurate restoration of joint geometry. This might be due to a lack of functional parameters for the measurement and availability of adequate implants for accurate restoration of joint geometry. From our point of view the two problems: stable stem fixation and joint geometry have to be addressed separately: Safe stem fixation on the one hand, adequate joint geometry on the other hand. With the use of standard implants compromises have to be made on either side. To avoid this dilemma, we propose alternative systems: A modular system with interchangeable necks as a standard implant for better fit and adequate joint geometry or a custom implant. In the presentation we address the interference of stem fit and joint geometry and discuss problems and advantages of modularity and custom implants

We undertook a review of the literature relating to the two basic stem designs in use in cemented hip replacement, namely loaded tapers or force-closed femoral stems, and the composite beam or shape-closed designs. The associated stem fixation theory as understood from in vitro studies and finite element modelling were examined with reference to the survivorship results for each of the concepts of fixation. It is clear that both design principles are capable of producing successful long-term results, providing that their specific requirements of stem metallurgy, shape and surface finish, preparation of the bone and handling of the cement are observed

Introduction: In the past, surgeons have found impaction bone grafting technically difficult leading to its limited use. This paper reviews the long term results and developments in instrumentation and techniques aimed at simplifying femoral impaction grafting at revision hip replacement. The expanded indications for this procedure are reviewed and recent results of stem fixation using radiostereometric analysis (RSA) are reported. Methods: The impaction bone grafting procedure, using a cemented collarless polished double taper stem, has been used in 66 hips (median patient age 63yrs) since 1993. The technique has undergone numerous developments. Modular tamps have been used in the last 29 hips and in the last seven hips, a pneumatic mechanical vibration device has been used in place of manual impaction. Stem subsidence at both the prosthesis-cement and cement-graft/bone interfaces was measured, more recently using radiostereometric analysis. Results: There was a high early incidence of failure in the initial cases but there have been no further revisions for mechanical failure at up to 15 years. Technique developments have resulted in dramatic improvements in stem fixation achieved. In the modular tamp cases, the mean stem subsidence at the cement-bone interface at 12 months was 0.07mm (0 to 0.7mm) at 12 months. The stem subsidence in the hips where the mechanical vibration device was used was 0.05mm (0 to 0.06mm). Femoral impaction grafting offers special advantages in younger patients include standard femoral stem revision and at the second stage of two stage revision for infection. Discussion and Conclusion: A stable cement-bone interface is achieved using advanced techniques of femoral impaction grafting that includes the use of modular impaction instruments. Early results of mechanical vibration impaction are encouraging. Femoral impaction grafting restores bone and new techniques simplify the femoral revision procedure

Introduction. Proper initial fixation of the stem in the femoral canal is important to achieve successful long-term clinical results in total hip arthroplasty (THA) and bipolar hemiarthroplasty (BHA). However, this factor fully relies on surgeon's experience and skill during the hammering process. The goal of this study is to evaluate the frequency of the stem hammering sound which enables the achievement of proper stem fixation and avoiding femoral bone fracture. Materials and methods. 57 patients who received BHA as a result of femoral neck fracture were evaluated. Intraoperative images of stem hammering were recorded using a digital video camera (Everio GZ-MG275, Victor, Japan). The frequency of the hammering sound was analyzed using a digital audio editor, GoldWave (GoldWave Inc.) (Figure 1). The frequency change during hammering was categorized into two groups, convergent and non-convergent, according to the frequency change pattern (Figure 2). The definition of “convergent group” is as follows: in the last five hammering sounds to finish the stem insertion, 1) Three consecutive hammering frequency shape and distribution 2) Formant peak frequency within the range of 3,000 Hz. Two types of cementless stems, SYNERGY SELECT II (tapered) and ECHELON TITANIUM (cylindrical, both from Smith & Nephew, Inc.) were used. Stem hammering was conducted using the same stem inserter. Canal Flare Index (CFI), Cortical Index (CI), Singh Index (SI), canal filling ratio, and the total number of stem-cortex contact zones were evaluated on x-ray images. The Mann-Whitney U-test was used for statistical analysis. Results. The number of contact zones was significantly different between convergent and non-convergent groups in both SYNERGY and ECHELON stems. However, no significant difference was found in CFI, CI, SI, and canal filling ratio. With the SYNERGY stem 24 cases showed convergence in hammering frequency and non-convergence in 16 cases. The mean total contact zones were 6.08±1.18 (convergent group) and 4.44±1.71 (non-convergent group). In the ECHELON group 9 cases showed convergence in hammering frequency and non-convergence in 8 cases. The total contact zones were 6.78±1.09 (convergent group) and 4.88±1.55 (non-convergent group) (Table 1). Discussion. Regardless of femoral geometry and stem design, hammering sound frequency was convergent when the stem-bone contact area increased. Change in the hammering sound frequency can provide reliable information during the stem insertion in terms of stem-bone contact to prevent bone fracture

INTRODUCTION. Recently, short shaped stem becomes popular in total hip arthroplasty (THA). Advantages of the short stem are preserving femoral bone stock, thought to be less thigh pain, suitable for minimally invasive THA. However, bony reaction around the short stem has not been well known. The purpose of this study was to compare the two years difference of radiographic change around the standard tapered round stem with the shorter tapered round stem. MATERIALS AND METHODS. Evaluation was performed in 96 patients (100 joints) who underwent primary THA. Standard tapered round stem (Bicontact D stem) was used in 44 patients from January 2011 to May 2013. Shorter stem (Bicontact E stem) was used in 56 patients from May 2015 to March 2016. The proximal shapes of these two stems are almost the same curvature. The mean age at surgery was 64 years. The mean BMI at surgery was 24.0 kg/m. 2. Eighty-six patients had osteoarthrosis and 10 patients had osteonecrosis. Evaluation was performed 2 years after surgery with standard AP radiographs. The OrthoPilot imageless navigation system was used during surgery. Evaluation of the stem fixation, stress shielding, and cortical hypertrophy were carried out. RESULTS. There were no differences of patient characteristics between the standard D stem group and the shorter E stem group. All 100 stems showed bony stable fixation two years after surgery. No subsidence was observed in both groups. No clear zone was observed around the stems in both groups. Cortical hypertrophy was observed 19 patients (43.2%) with the standard D stem group and 13 patients (23.2%) with the shorter E stem group. The standard D stem group showed higher incidence of cortical hypertrophy. Stress shielding was observed 35 patients (80%) with the standard D stem group and 42 patients (75%) with the shorter E stem group. The number of grade 1 and grade 2 stress shielding cases were 13 and 22 with the standard D stem group and 10 and 32 with the shorter E stem group, respectively. There were no grade 3 stress shielding case in both groups. Regarding the incidence of stress shielding, there was no difference between the two groups. DISCUSSION. This study demonstrated that the shorter stem showed less incidence of cortical hypertrophy compared to the standard stem. With radiographic evaluation, both standard and shorter stem showed good fixation. The meaning of cortical hypertrophy, whether it is a good reaction for the femur or not, has not been clarified yet. Less bony reaction around the shorter stem may suggest the potential for better clinical performance of the shorter stem compare to the standard stem

Aims

The aim of this study was to evaluate medium- to long-term outcomes and complications of the Stanmore Modular Individualised Lower Extremity System (SMILES) rotating hinge implant in revision total knee arthroplasty (rTKA) at a tertiary unit. It is hypothesized that this fully cemented construct leads to satisfactory clinical outcomes.

We report the review of performance and problems of Metasul Hip System with metallic sliding face during mean time of 11 years or longer. Subjects and methods: Twenty-three joints in 22 patients. 17 females and 5 males treated using cementless Metasul THA in our hospital from November of 1995 to April of 1998 were selected as subjects. The mean age at the time of surgery was 59 years, and disease included degenerative hip disease in 16 joints, femoral head necrosis in 5 joints, and rheumatoid arthritis in 2 joints. Mean follow-up period was 11 years and 3 months. We have investigated clinical results (JOA score), stem fixation by radiography (Engh), setting angle of socket, and presence or absence of osteolysis by CT, and the poor cases after surgery and problems were clarified. Results: Clinical results (JOA score) were improved from preoperative mean of 41.3 points to mean of 89.3 points at the time of investigation. Stem fixation examination by radiography (Engh) for bone ingrown resulted in 95% in ingrown and 5% in ingrown suspension, showing excellent fixation. The abduction angle of the socket was 38.8±4.5 degrees, and the anteversion angle was 14.6±7.7 degrees, revealing that precise surgery was conducted. There were no joints which showed loosening in stem or socket, but CT imaging showed osteolysis in 5 joints (22%) in the stem side and 12 joints (52%) in the acetabular side. Dislocation in Poly Liner occurred in 4 cases which needed revision surgery with accumulated survival rate of 82.6. Summary: When cementless Metasul Hip System was used, fixation of stem/metal shell was excellent, but there were problems in thickness and fixation of Poly Liner. Due to augmentation of activity, backside wear occurred, and osteolysis or dislocation of the liner was induced. THA System such as M2a which improves these defects using metallic liner may be promising hereafter

Aims

Endoprosthetic reconstruction following distal femur tumour resection has been widely advocated. In this paper, we present the design of an uncemented endoprosthesis system featuring a short, curved stem, with the goal of enhancing long-term survivorship and functional outcomes.

Cemented stem fixation is a proven technique in total hip arthroplasty (THA), however, aseptic loosening is a noted complication. Cementless fixation is also popular in THA, however thigh pain and osteolysis are known problems with short-term and long-term follow- up, respectively. In order to improve the initial development and durability of the osseointegration of porous coated cementless implants, hydroxyapatite (HA) has been claimed to provide a biological adjuvant for femoral stem fixation in THA. There is no prospective, randomised long-term study comparing clinical radiographic findings between proximally HA-coated and non-HA coated surfaces of an identical stem design. We investigated 177 patients (199 hips) who received either HA-coated or non-HA coated stems. Clinical information from 163 patients (181 hips), including walking ability, thigh pain, sports activity, and overall patient satisfaction was collected. Evidence of radiolucencies, stem migration, and canal fill was measured on AP and lateral radiographs. In addition, tension trabeculae on the lateral aspect of the proximal stem and stress-induced remodelling of cancellous bone against porous surface (SIRCAP) were noted as signs of bone ingrowth. Both groups of patients performed well on the basis of HSS scores, walking ability, sports activity, and overall patient satisfaction. However the non-HA group demonstrated a significant increase (p< 0.05) in activity- related thigh pain. There were no significant radiographic differences between patient cohorts with all stems demonstrating bone ingrowth. In our prospective, randomised study, we conclude that the use of HAcoated stems results in increased clinical satisfaction to the THA patient

Aims

Both the femoral and tibial component are usually cemented at revision total knee arthroplasty (rTKA), while stems can be added with either cemented or press-fit (hybrid) fixation. The aim of this study was to compare the long-term stability of rTKA with cemented and press-fitted stems, using radiostereometric analysis (RSA).

Stems are a crucial part of implant stabilization in revision total knee arthroplasty. In most cases the metaphyseal bone is deficient, and stabilization in the diaphyseal cortical bone is necessary to keep the implant tightly fixed to bone and to prevent tilt and micromotion. While sleeves and cones can be effective in revision total joint arthroplasty, they are technically difficult and may lead to major bone loss in cases of loosening or infection, especially if the stem is cemented past the cone. A much more conservative method is to ream the diaphysis to the least depth possible to achieve tight circumferential fixation, and to apply porous augments to the undersurface of the tibial tray or inner surface of the femoral component to allow them to bottom out against the bone surface and apply compressive load. If a robust, strong taper, stem and component combination is used, rim contact on only one side is necessary to achieve rigid permanent fixation. Porous and non-porous stems are available. The non-porous stems should have a spline surface that engages the diaphyseal bone and achieves rigid initial fixation but does not provide long-term axillary support. In that way the porous rim-engaging surface can bear compressive load and finally unload the stem and taper junction. Correctly designed stems do not stress relieve unless they are porous-coated. In situations where metaphyseal bone is not available, porous-coated stems that link to hinge prostheses are a very important part of the armamentarium in complex revision arthroplasty. Use of stems requires experience and special technique. Slight underreaming and initial scratch fit are necessary techniques. This does not result in tight fixation every time because split of the cortex does occasionally occur. In most cases these splits do not need to be repaired, but when there is a question, an intra-operative x ray should be taken and the surgeon should be prepared to repair the fracture. Stems are an essential part of revision total knee arthroplasty. A tightly fit stem in the diaphysis is necessary for fixation when metaphyseal bone is deficient. No amount of cement pressed into the deficient metaphyseal bone will substitute for rigid stem fixation

Elderly femoral neck fractures are often treated with cemented stems according to the reason that bone quality of the patients is not good enough to obtain the initial stability for supporting press fit cementless stem. Some elderly patients also have medullary expanding so called stovepipe canals which make initial stability of press fit stems difficult. Stems with lateral flare have some mechanical advantages to obtain proximal fixation compare to the straight stems without lateral flare. Concerning to initial stability, their vertical loads can be supported not only by proximal medial cortex but also by proximal lateral cortex. The stems also have rotational stability because of the proximal high fit and fill. As lateral flare is a transverse extension in axial section, the stem occupies the proximal canal widely. So it provides strong rotational stability. The purpose of this study was to evaluate the outcome of press fit cementless stem with lateral flare for elderly femoral neck fractures with poor bone quality and with medullary expanding. We performed a retrospective review of the clinical records and radiograghs of consecutive 42 patients (42 hips) of femoral neck fracture operated with cement-less stems with lateral flare in 2005 and 2006. In this period, all displaced femoral neck fractures were operated using cementless stems with lateral flare (Revelation Hip System, DJO, USA) in our hospital. We could follow 24 patients for over one year. 12 of 24 patients had so called stovepipe canals according to Canal Flare Index< 3.0 (Noble et al). Minimum follow up duration was one year. The mean age of the patients at the time of operation was 78.2 years. The mean duration of follow-up was one year and three month. At the time of final follow-up, stem subsidence, stem fixation, spot welds and demarcation line at distal part of stem are assessed on radiograph. And operation time, blood loss at operation and complaint of thigh pain through all the follow up period are also investigated on clinical record. There was no stem subsidence over 2mm and demarcation line in two cases. All stems were assessed bone-grown fixation. We could find at least one spot welds in all patients around porous coated part of the stem. The mean operation time was 60.1 min. and mean blood loss was 240.5 ml. There was no patient who complaints of thigh pain after operation. Cementless stems with lateral flare were seemed to obtain good initial stem fixation for elderly femoral neck fracture patients even they have poor bone quality and medullary expanding

The Failed Femoral Neck Fracture. For the young patient: Attempt to preserve patient's own femoral head. Clinical results reasonably good even if there are patches of avascular necrosis. Preferred methods of salvage: valgus-producing intertrochanteric femoral osteotomy: puts the nonunion under compression. Other treatment option: Meyer's vascularised pedicle graft. For the older patient: Most reliable treatment is prosthetic replacement. Decision to use hemiarthroplasty (such as bipolar) or THA based on quality of articular cartilage, perceived risk of instability problem. In most patients THA provides higher likelihood of excellent pain relief. Specific technical issues: (1) hardware removal: usually remove after hip has first been dislocated (to reduce risk of femur fracture); (2) Hip stability: consider methods to reduce dislocation risk: larger diameter heads/dual mobility/anteriorly-based approaches; (3) Acetabular bone quality: poor because it is not sclerotic from previous arthritis; caution when impacting a pressfit cup; low threshold to augment fixation with screws; don't overdo reaming; just expose the bleeding subchondral bone. A reasonable alternative is a cemented cup. The Failed Intertrochanteric Hip Fracture. For the young patient: Attempt to salvage hip joint with nonunion takedown, autogenous bone grafting and internal fixation. For the older patient: Decision to preserve patient's own hip with internal fixation versus salvage with hip arthroplasty should be individualised based on patient circumstances, fracture pattern, bone quality. THA is an effective salvage procedure for this problem in older patients. If prosthetic replacement is chosen special considerations include:. THA vs. hemiarthroplasty: hemiarthroplasty better stability; THA more reliable pain relief. Removal of hardware: be prepared to remove broken screws in intramedullary canal. Management of bone loss: bone loss to level of lesser trochanter common. Often requires a calcar replacement implant. Proximal calcar build-up size dictated by bone loss. Length of stem: desirable to bypass screw holes from previous fixation, if possible. Stem fixation: cemented or uncemented fixation depending on surgeon preference, bone quality. If uncemented, consider diaphyseal fixation. Greater trochanter: often a separate piece, be prepared to fix with wires or cable grip. Residual trochanteric healing, hardware problems not rare after THA

Mastering the Art of Cemented Femoral Stem Fixation: Fixation of cemented femoral stems is reproducible and provides excellent early recovery of hip function in patients 60 to 80 years old. The durability of fixation has been evaluated up to 20 years with 90% survivorship. The mode of failure of fixation of cemented total hip arthroplasty is multi-factorial; however, good cementing techniques and reduction of polyethylene wear have been shown to reduce its incidence. The importance of surface roughness for durability of fixation is controversial. This presentation will describe my personal experience with the cemented femoral stem over 30 years with 3 designs and surface roughness (RA) ranging from 30 to 150 microinches. Cemented Primary Acetabulum: I am going to present a technique of cementing an all-poly socket. We have looked at our all-poly socket from 1992 to 1998 and the total number of hips are over 1,000, with a follow-up of 2 to 8 years. We have not revised a single socket for fixation failure

Introduction and Objectives: At present, cementless stems offer a reliable alternative for survival of total hip prostheses (THP). This study analyzes the clinical and radiographic results obtained using the Zweymüller SL stem in patients with an average follow-up time of 10 years. Materials and Methods: This is a study of 100 cement-less THP (Balgrist cups, SL stems) implanted between June 1991 and February 1995 in 93 patients (7 bilateral). Patients were 55% male and 45% female, with an average age of 58.5 years (20–74). Diagnoses were 72% coxarthrosis, 13% avascular necrosis, 5% fractures, 4% rheumatism, 2% Perthes disease, 2% dysplasia, and 2% post-infection sequelae. Two deaths occurred during the follow-up period (unrelated to THP). No cases were lost. Average follow-up time was 10 years (range: 8 to 12 years). Clinical evaluation was done using the Merle D’Aubigné scale as modified by Kramer and Maichl, to numerically evaluate degree of pain and walking capacity. Radiographic evaluation included determining radiolucent lines, sclerosis, osteolysis in the Gruen zones, stem subsidence, heterotopic ossification, and type of stem fixation. Survival analysis was done according to Kaplan-Meier at 10 years using prosthetic revision as the endpoint. Results: Clinical evaluation based on the modified Merle D’Aubigné scale was as follows: 81% very good results, 2% good, 3% satisfactory, 2% fair, and 11% poor (this last group included revision THP). Radiographic evaluation showed 9% with radiolucent lines in zone 1, 6% in zone VII, and one case with osteolysis in zones II and VI, the latter in conjuction with aseptic loosening of the stem. There was heterotopic ossification in 28% of cases and subsidence in 2 cases (one asymptomatic and the other aseptic loosening, which is pending revision). Stem fixation was excellent in 67% of cases, good in 32%, and poor in 1%. There were 7 revisions in the survival analysis: 4 of the cup, 2 of the entire prosthesis due to septic loosening, and one of the head of the stem. All of this resulted in 10-year survival rates of 92% (0.92 +/− 0.06; p< 0.05) for the THP and 97% (0.97 +/− 0.03; p< 0.05) for the SL stem. Discussion and Conclusions: Cementless Zweymüller SL stems offer excellent survival rates. In our series, only one stem failed (1%), and is currently awaiting revision

Periprosthetic fractures around the femur during and after total hip arthroplasty (THA) remain a common mode of failure. It is important therefore to recognise those factors that place patients at increased risk for development of this complication. Prevention of this complication, always trumps treatment. Risk factors can be stratified into: 1. Patient related factors; 2. Host bone and anatomical considerations; 3. Procedural related factors; and 4. Implant related factors. Patient Factors. There are several patient related factors that place patients at risk for development of a periprosthetic fracture during and after total hip arthroplasty. Metabolic bone disease, particularly osteoporosis increases the risk of periprosthetic fracture. In addition, patients that smoke, have long term steroid use or disuse, osteopenia due to inactivity should be identified. A metabolic bone work up and evaluation of bone mineralization with a bone densitometry test can be helpful in identifying and implementing treatment prior to THA. Pre-operative Host Bone and Anatomic Considerations. In addition to metabolic bone disease the “shape of the bone” should be taken into consideration as well. Dorr has described three different types of bone morphology (Dorr A, B, C), each with unique characteristics of size and shape. It is important to recognise that not one single cementless implant may fit all bone types. The importance of templating a THA prior to surgery cannot be overstated. Stem morphology must be appropriately matched to patient anatomy. Today, several types of cementless stem designs exist with differing shape and areas of fixation. It is important to understand via pre-operative templating which stem works best in what situation. Procedural Related Factors. There has been a resurgence in interest in the varying surgical approaches to THA. While the validity and benefits of each surgical approach remains a point of debate, each approach carries with it its own set of risks. Several studies have demonstrated increased risk of periprosthetic fractures during THA with the use of the direct anterior approach. Risk factors for increased risk of periprosthetic fracture may include obesity, bone quality and stem design. Implant Related Factors. As mentioned there are several varying cementless implant shapes and sizes that can be utilised. There is no question that cementless fixation remains the most common mode of fixation in THA. However, one must not forget the role of cemented fixation in THA. Published results on long term fixation with cemented stems are comparable if not exceeding those of press fit fixation. In addition, the literature is clear that cemented fixation in the elderly hip fracture patient population is associated with a lower risk of periprosthetic fracture and lower risk of revision. The indication and principles of cemented stem fixation in THA should not be forgotten

Cementless femoral stems of many designs now provide dependable long-term fixation and excellent, near normal function in patients of all ages, sexes and level of activity. However, a number of issues related to cementless stem fixation could be further improved: Optimization of load transfer to proximal femur to minimise fracture risk and maximise bone preservation; Elimination of proximal-distal mismatch concerns, including bowed femurs; Facilitation of femoral stem insertion, especially for Anterior and MIS exposures; Facilitation of revision with implants capable of providing durable fixation for active patients. The potential benefits of short stem femoral THA implants include: Ease of insertion; Reproducibility of insertion; Avoidance of issues related to proximal-distal anatomic mismatch or variations in proximal femoral diaphyseal anatomy (e.g. femoral bowing); Facilitation of MIS surgical approaches, especially anterior exposures; Optimization of proximal femoral load transfer with consequent maximization of proximal bone preservation. The purpose of this presentation is to describe the design rationale and characteristics of short (< 120 mm) uncemented primary THA femoral stems and to evaluate the clinical and radiographic results of short stems. Outcome results extending beyond 10 years support the proposition that short stems of appropriate design provide dependable long-term fixation and equivalent clinical results to those currently achievable with cementless stems of conventional length in patients of all ages, sexes and level of activity

Aims

The aim of this study was to evaluate the survival of a collarless, straight, hydroxyapatite-coated femoral stem in total hip arthroplasty (THA) at a minimum follow-up of 20 years.

The December 2023 Hip & Pelvis Roundup³⁶⁰ looks at: Early hip fracture surgery is safe for patients on direct oral anticoagulants; Time to return to work by occupational class after total hip or knee arthroplasty; Is there a consensus on air travel following hip and knee arthroplasty?; Predicting whether patients will achieve minimal clinically important differences following hip or knee arthroplasty; High-dose dual-antibiotic-loaded cement for hip hemiarthroplasty in the UK (WHiTE 8): a randomized controlled trial; Vitamin E – a positive thing in your poly?; Hydroxapatite-coated femoral stems: is there a difference in fixation?

Aims

When performing revision total hip arthroplasty using diaphyseal-engaging titanium tapered stems (TTS), the recommended 3 to 4 cm of stem-cortical diaphyseal contact may not be available. In challenging cases such as these with only 2 cm of contact, can sufficient axial stability be achieved and what is the benefit of a prophylactic cable? This study sought to determine, first, whether a prophylactic cable allows for sufficient axial stability when the contact length is 2 cm, and second, if differing TTS taper angles (2° vs 3.5°) impact these results.

The August 2023 Hip & Pelvis Roundup³⁶⁰ looks at: Using machine learning to predict venous thromboembolism and major bleeding events following total joint arthroplasty; Antibiotic length in revision total hip arthroplasty; Preoperative colonization and worse outcomes; Short stem cemented total hip arthroplasty; What are the outcomes of one- versus two-stage revisions in the UK?; To cement or not to cement? The best approach in hemiarthroplasty; Similar re-revisions in cemented and cementless femoral revisions for periprosthetic femoral fractures in total hip arthroplasty; Are hip precautions still needed?

Aims

Obtaining solid implant fixation is crucial in revision total knee arthroplasty (rTKA) to avoid aseptic loosening, a major reason for re-revision. This study aims to validate a novel grading system that quantifies implant fixation across three anatomical zones (epiphysis, metaphysis, diaphysis).

Aims

Cementing in arthroplasty for hip fracture is associated with improved postoperative function, but may have an increased risk of early mortality compared to uncemented fixation. Quantifying this mortality risk is important in providing safe patient care. This study investigated the association between cement use in arthroplasty and mortality at 30 days and one year in patients aged 50 years and over with hip fracture.

Aims

Despite higher rates of revision after total hip arthroplasty (THA) being reported for uncemented stems in patients aged > 75 years, they are frequently used in this age group. Increased mortality after cemented fixation is often used as a justification, but recent data do not confirm this association. The aim of this study was to investigate the influence of the design of the stem and the type of fixation on the rate of revision and immediate postoperative mortality, focusing on the age and sex of the patients.

Aims

Refobacin Bone Cement R and Palacos R + G bone cement were introduced to replace the original cement Refobacin Palacos R in 2005. Both cements were assumed to behave in a biomechanically similar fashion to the original cement. The primary aim of this study was to compare the migration of a polished triple-tapered femoral stem fixed with either Refobacin Bone Cement R or Palacos R + G bone cement. Repeated radiostereometric analysis was used to measure migration of the femoral head centre. The secondary aims were evaluation of cement mantle, stem positioning, and patient-reported outcome measures.

Aims

The aim of this investigation was to compare risk of infection in both cemented and uncemented hemiarthroplasty (HA) as well as in total hip arthroplasty (THA) following femoral neck fracture.

Aims

The aim of this study was to compare the mid-term patient-reported outcome, bone remodelling, and migration of a short stem (Collum Femoris Preserving; CFP) with a conventional uncemented stem (Corail).

Aims

Breast cancer survivors have known risk factors that might influence the results of total hip arthroplasty (THA) or total knee arthroplasty (TKA). This study evaluated clinical outcomes of patients with breast cancer history after primary THA and TKA.

Aim. One of the most challenging problems in total knee arthroplasty (TKA) is periprosthetic infection. A major problem that arises in septic revision TKA (RTKA) are extended bone defects. In case of extended bone defects revision prostheses with metaphyseal sleeves are used. Only a few studies have been published on the use of metaphyseal sleeves in RTKA - none were septic exclusive. The aim of our study was to determine the implant survival, achieved osseointegration as well as the radiological mid-term outcomes of metaphyseal sleeve fixation in septic two-stage knee revision surgery. Method. Clinical and radiological follow-up examinations were performed in 49 patients (25 male and 24 female). All patients were treated with a two-stage procedure, using a temporary non-articulating bone cement spacer. The spacer was explanted after a median of 12 weeks (SD 5, min. 1 – max. 31) and reimplantation was performed, using metaphyseal sleeves in combination with stem fixation. Bone defects were classified on preoperative radiographs using the Anderson Orthopaedic Research Institute (AORI) classification. During follow-up postoperative range of motion (ROM) was measured and radiographs were performed to analyse: (i) osseointegration (radiolucent lines and spot welds), (ii) leg alignment, (iii) patella tilt and shift. Results. All types of bone defects were found on the tibial (4× type 1, 7× type 2a, 26× type 2b, 9× type 3) as well as on the femoral side (1× type 1, 4× type 2a, 20× type 2b, 6× type 3). Mean follow-up time was 4.7 years (minimum 1 year). In total 12 knees (24.5%) had to be re-revised, all due to re-infection. We did not encounter any case of aseptic loosening. In 3 patients (6.8%) we detected an insufficient osseointegration, but no patient had to be re-revised due to only minimal or to the absence of symptoms and no clinical signs of loosening. The ROM (mean 93°, SD 20.6, min. 25° max. 125°) has shown very satisfying results at the time of follow-up. Malalignment was detected in 4 patients (10.3%), a patella tilt in 7 (19.4%) and a patella shift in 14 (48.3%). Conclusions. Metaphyseal Sleeves have shown very promising mid-term results regarding osseointegration and aseptic implant survival in RTKA with compromised metaphyseal bone stock. Our results indicate that they are a reliable fixation option in septic RTKA patients

A good primary mechanical stability is a prerequisite for secondary cementless stem fixation by osseointegration. The construction, basic shapes and their development, as well as the nature of the surface in the CLS system are thus directed towards this goal. The biomechanical concept of the CLS stem is characterised by the three-dimensional V-form, the strongly accentuated ribs in the proximal region and the all-round conical form of the distal part of the stem. The construction uses the adaptable trabeculum for the primary fixation. The features that characterise the CLS stem are found both in the classical version and the varus version. The fixation of the stem in the proximal area should guarantee that transmission of force is retained within this area. The interposition of the cancellous structures reduces the danger of the bond between the bone and prosthesis becoming stiff. On introduction, the axial ribs exercise a cutting action and promote stability. In order to avoid tension peaks, the surfaces of the distal part of the stem are well rounded. The shape of the distal part of the stem is kept relatively slender, thus direct contact with the cortex is avoided. This means reduced incidence of pain for the patient, plus the new trabecular structures can form between the cortex and the implant, which eventually result in osseointegration. To what extent and how quickly an implant becomes integrated is not just a question of primary stability. Important factors that have an influence also include the material and the surface structures of the prosthesis. It is generally the case that new bone grows preferentially on protruding parts such as prosthesis ribs or edges, and also on existing trabeculae, such as those altered by the surgery. The formation of new bone tissue in association with the CLS prosthesis was thoroughly investigated in many histological studies. The coarse-grained titanium alloy is, to a great extent, osteophilic. This is demonstrated by the fact that bone marrow or new bone can form directly on the surface of the CLS prosthesis. The indications can be calculated on the basis of four key parameters: age, sex, the degree of osteoporosis, and the morphology of the femur. The morphological-cortical index (MCI) is used as an instrument to determine the shape of the femur. This provides a reliable method of classification of one of three basic morphological types: trumpet-shaped, cylindrical, and dysplastic. The first 300 consecutive primary total hip arthroplasty (THA) procedures (299 patients), from Dec. 1983 to Apr. 1985, using a collarless, three-dimensional tapered, straight, titanium alloy stem with a grit-blasted surface, were evaluated clinically and radiographically in up to 16 years of follow-up. Radiographic evaluation assessed Engh’s implant-bone femoral fixation score, implant-bone demarcation, and periprosthesis osteolysis. The average duration of long-term radiographic follow- up was 12.6 years (10–16 years). Patients were evaluated clinically by the HHS system. At last examination, five hips were lost to follow-up and 69 patients had died. The femoral revision rate was 7% (two aseptic loosening, five septic, 12 osteolysis). Femoral component survivorship was 95% at 10 years and 90% at 14 years. Femoral implant-bone fixation was stable, bone ingrowth in 97% stable, fibrous fixation in 1% and unstable, fibrous-fixation in 2% of the cases revised for acetabular mobilisation. The grit-blasted, press-fit, collarless, tapered femoral component continued to perform well. While considering a “first-generation” cementless stem, CLS is still in use without virtually any design modifications

Despite the best of technique, when faced with a sub-capital or per-trochanteric fracture, inevitably there are failures of proximal fixation. These situations provide unique challenges for the reconstructive surgeon. While there are specific issues related to either sub-capital or per-trochanteric fractures, there also are many commonalities. The causes of failure are nonunion, malunion, failure of fixation or avascular necrosis. In all cases, it is imperative to rule out infection. Since the surgery is now elective, the patient's medical status must be optimised prior to the intervention. Basic surgical principles apply to both fracture types. Use the old incision (if possible) and choose an approach that can be extensile. Of course, the old hardware needs to be removed – this task can be quite frustrating, so good preparation and patience is imperative. Retrieve old operative notes to identify the type of hardware so that any special tools needed are available. Hardware can be intra-osseous in location and excavation of the hardware may require bone osteotomy. These patients are at higher risk of post-operative dislocation, so absolute hip stability must be achieved and confirmed in the OR. Bigger heads and dual mobility options improve stability provided that the components are properly positioned and offset and leg length are restored. Subcapital fractures provide certain specific issues related to stem choice. While, my bias is towards THA because of better chance of complete pain relief, especially in community ambulators, certainly bipolar arthroplasties can be a satisfactory solution. Stem fixation can be either cemented or cementless. For per-trochanteric fractures in younger patients, repeat osteosynthesis should be considered if the femoral head is viable. Bone deformity – trochanteric overhang, shaft offset – may necessitate an osteotomy as part of the reconstruction. While proximal fixation primary type stems are often possible, distal fixation revision stems may be required. Any bone defects related to screw holes should be bypassed by the femoral component

Aims

The aim of this study was to compare the cost-effectiveness of cemented hemiarthroplasty (HA) versus hydroxyapatite-coated uncemented HA for the treatment of displaced intracapsular hip fractures in older adults.

Distal femoral replacement is an operation long considered as salvage operation for neoplastic conditions. Outcomes of this procedure for difficult knee revisions with bone loss of distal femur have been sparsely reported. We present the early results of complex revision knee arthroplasty using distal femoral replacement implant, performed for severe osteolysis and bone loss. Retrospective review of clinic and radiological results of 25 consecutive patients operated at single centre between January 2010 and December 2014. All patients had single type of implant. All data was collected till the latest follow up. Re-revision for any reason was considered as primary end point. Mean age at surgery was 72.2 years (range 51 – 85 years). Average number of previous knee replacements was 2.28 (range 1 to 6). Most common indications were infection, aseptic loosening and peri-prosthetic fracture. Average follow up was 24.5 months (range: 3–63 months). 1 patient died 8 months post-op due to unrelated reasons. Re-revision rate was 2/25 (8%) during this period. One was re-revised for aseptic loosening and one was revised for peri-prosthetic fracture of femur. Two other peri-prosthetic fractures were managed by open reduction and internal fixation. All 3 peri-prosthetic fractures occurred with low energy trauma. It is noteworthy that there was no hinge or mechanical failures of the implant. Peri-prosthetic fracture in 12% of patients in this series is of concern. There are no similar studies to compare this data with. The length of the stem, type of fixation of the stem, weight of the distal femoral component of implant can be postulated as factors contributing to risk of peri-prosthetic fracture

Aims

The aim of our study was to investigate the effect of asymmetric crosslinked polyethylene liner use on the risk of revision of cementless and hybrid total hip arthroplasties (THAs).

Hybrid fixation of total joint arthroplasty has been an accepted form of surgical approach in multiple joints. Principles of implant fixation should focus on durability providing secure long-term function. To date there is no conclusive evidence that pressed fit humeral stem fixation has an advantage over well-secured cemented humeral fixation. In fact, need for revision arthroplasty due to inadequate implant fixation has almost universally revolved around failure of cement fixation and loosening of the glenoid component. A case will be made based on 30 years of experience of one surgeon performing total shoulder arthroplasty using secure modern cement fixation techniques of humeral components. More recently, over the last 10 years, extremely high rate of durable secure glenoid implant fixation has been achieved using tantalum porous anchorage with polyethylene glenoid components. This has resulted in no cases of loosening of glenoid fixation and only 1 case of glenoid component fracture with greater than 95% survivorship over a 10 year period. A combination of well cemented humeral stem and trabecular metal anchorage of the glenoid has provided durable lasting function in primary total shoulder arthroplasty

Aims

Total hip arthroplasty (THA) is a very successful and cost-effective operation, yet debate continues about the optimum fixation philosophy in different age groups. The concept of the 'cementless paradox' and the UK 'Getting it Right First Time' initiative encourage increased use of cemented fixation due to purported lower revision rates, especially in elderly patients, and decreased cost.

Despite the best of technique when faced with a sub-capital or per-trochanteric fracture, inevitably there are failures of proximal fixation. These situations provide unique challenges for the reconstructive surgeon. While there are specific issues related to either sub-capital or per-trochanteric fractures, there also are many commonalities. The causes of failure are nonunion, malunion, failure of fixation or avascular necrosis. In all cases, it is imperative to rule out infection. Since the surgery is now elective, the patient's medical status must be optimised prior to the intervention. Basic surgical principles apply to both fracture types. Use the old incision (if possible) and choose an approach that can be extensile. Of course, the old hardware needs to be removed – this task can be quite frustrating, so good preparation and patience is imperative. Retrieve old OP notes to identify the type of hardware so that any special tools needed are available. Hardware can be intra-osseous in location and excavation of the hardware may require bone osteotomy. These patients are at higher risk of postoperative dislocation, so absolute hip stability must be achieved and confirmed in the OR. Bigger heads and dual mobility options improve stability provided that the components are properly positioned and offset and leg length are restored. Subcapital fractures provide certain specific issues related to stem choice. While, my bias is towards total hip arthroplasty because of better chance of complete pain relief, especially in community ambulators, certainly bipolar arthroplasties can be a satisfactory solution. Stem fixation can be either cemented or cementless. For per-trochanteric fractures in younger patients, repeat osteosynthesis should be considered if the femoral head is viable. Bone deformity – trochanteric overhang, shaft offset – may necessitate an osteotomy as part of the reconstruction. While proximal fixation primary type stems are often possible, distal fixation revision stems may be required. Any bone defects related to screw holes should be bypassed by the femoral component

Femoral offset restoration is related to low rates of wear and dislocation. Replication of the native hip anatomy improves prosthesis survival, whereas increasing the femoral offset elevates the torque stresses, thus inducing a risk of suboptimal stem fixation. Although the Corail (DePuy Synthes, St Priest, France) uncemented stem has an excellent record of fixation, an unexpectedly number of aseptic loosenings has been noted in our institution. We sought to characterize the clinical parameters observed in a group of patients who have experienced metaphyseal aseptic loosenings with the collarless version of the Corail uncemented femoral component; describe the radiographic findings in this group of patients; expose the intraoperative findings in the cases that needed revision surgery and to calculate a possible frequency of this complication. We present a series of 15 metaphyseal debondings of the collarless version of the Corail uncemented stem in primary total hip arthroplasty. Eleven men and four woman with an average age of 60 years old (range: 42 to 81 years old) and a previous history of osteoarthritis presented with thigh pain and limping at an average of 33 months postoperative (range: 5 to 100 months). Seven cases presented a Dorr´s classification type A femur and 8 cases a type B femur. In 10 of the 15 cases a 36 mm ceramic on ceramic bearing surface was implanted and in 5 a 28 mm diameter ceramic on polyethylene pair. Radiographic assessment of the failures evidenced an increase in femoral offset of 6.2 mm in average (range: 0 to 17 mm). Nine of the 15 cases had a standard offset stem and 3 an extended offset stem. Leg length discrepancy was in average 2.4 mm (range: 0 to 8 mm). None of the failures presented a more than 2 mm subsidence. Alignment of these stems was in average 2.1 degrees of varus (range: 0 to 5 degrees). Six cases were revised to a long cemented or uncemented stem, 2 cases were lost and 7 cases are awaiting revision surgery. Although the incidence of this complication was low (15 failures in 855 cases in 10 years = 1.75%), we are concerned about the real magnitude of this problem, as this mode of failure was observed up to 8 years after implantation. Enhanced lateralization of the hip, independently of the type of stem, may have played a role in the infrequent early failures of this popular design. Routine use of “fine tunning” preoperative planning in order to avoid offset enhancement is strongly reccommended, as this was the only suspected factor that was present in almost all the failures we observed

Cementless stem fixation is a widely used method of stem revision in North America and elsewhere in the world. There is abundant literature in its support. Most of the reports from 1985 to 2005 related to proximally or extensively porocoated designs, the former falling into disfavor with time because of unpredictable outcomes. With few exceptions (e.g. S-ROM) the modularity of these designs was limited to the head/neck junction. But this generation of designs was associated with some issues such as insertional fractures, limited control of anteversion (and risk of dislocation), limited applicability in the setting of severe bone loss (Paprosky Type 4 osteolysis or Vancouver Type B3 periprosthetic fracture), as well as ongoing concern relating to severe proximal stress shielding. In the past decade we have seen the mounting use of a new design concept: tapered fluted titanium stems (TFTS), which incorporate the advantages of titanium (for less flexural rigidity), conical taper (for vertical taper-lock stability), longitudinal ribs or flutes (for rotational stability), and surface preparation which attracts bone ongrowth for long term fixation. Four consecutive reports from our center have documented the superiority of the TFTS in our hands, with encouraging outcomes even when dealing with severe bone loss or periprosthetic fractures. There is an increasing body of other literature which reports a similar experience. Furthermore, with increasing experience and confidence in this design concept, we now use a monoblock or non-modular design in the majority of cases in which a TFTS is indicated. This circumvents the potential drawbacks of stem modularity, including taper corrosion and taper junction fracture. Our recent report of this concept in 104 cases with a 2-year minimum follow-up supports the use of this concept in many if not most stem revisions. The question remains as to which should be favored? Because of equipoise in the outcomes of the two fundamental stem designs, at least in our hands, clearly the surgeon needs to ask other, more practical questions:. Am I familiar enough with the TFTS technique so as to bypass the potential versatility of the modular stem for the simplicity and potential cost savings of the non-modular?. Is this a case in which modularity will offer me distinct advantages (periprosthetic fracture, and severe bone loss as examples). Should I introduce the nonmodular TFTS to my practice, choosing straightforward cases first; ones in which I would comfortably and with confidence use an extensively porocoated stem?

As an increasing number of young, active, large patients are becoming candidates for total hip replacements, there is an increasingly urgent need to identify arthroplasties that will be durable, highly functional and amenable to possible future successful revision. In an era when cemented femoral stems were the primary implant option, the concept of a surface replacement was attractive and, perhaps, appropriate. However, cementless femoral stems of many designs now provide dependable long-term fixation and excellent, near normal function in patients of all ages, sex and level of activity. However, a number of issues related to cementless stem fixation could be further improved: Optimization of load transfer to proximal femur to minimise fracture risk and maximise bone preservation; Elimination of proximal-distal mismatch concerns, including bowed femurs; Facilitation of femoral stem insertion, especially with MIS THA exposures; Facilitation of revision with implants capable of providing durable fixation for active patients. The potential benefits of short stem femoral THA implants include: Ease of insertion; Reproducibility of insertion; Avoidance of issues related to proximal-distal anatomic mismatch or variations in proximal femoral diaphyseal anatomy (e.g. femoral bowing); Facilitation of MIS surgical approaches, especially anterior exposures; Optimization of proximal femoral load transfer with consequent maximization of proximal bone preservation. The purpose of this presentation is to describe the design rationale and characteristics of short (< 115 mm) uncemented primary THA femoral stem, to evaluate the clinical and radiographic results of short stems and to discuss the possible drawbacks specific to the use of short stems

The value of joint registries is to (1) provide large scale longitudinal follow-up of classes of implants and individual implants—thereby providing potential for improved performance—and (2) serve as a tripwire for unexpected problem implants which is well appreciated. The purpose of this talk is not to reiterate the value of joint arthroplasty registries, but rather to look at several key findings from joint registries around the world and discuss what these mean for orthopaedic surgery today. Observation #1: Registries can tell us where the biggest problems are so we can act on them: Example: Early failures—those occurring in the first two years—account for about half of all failures by ten years. Early failures consist of mainly technically related problems and infections. If we can reduce these problems, we can reduce the number of patients having a second surgery after joint replacement by almost half. For one type of early failure (infection), the registry data show rate of infection after THA and TKA has not declined substantially in the last 20 years. We need major innovation in this area to solve this problem. On the other hand, registry data show early failures in older patients after THA are often due to periprosthetic femur fracture: we can solve this problem now with choice of stem fixation or prophylactic wires in high risk patients. Observation #2: Innovation can and does work! It is not correct to suggest that no new implants have led to improved results. Example: Registry data demonstrate that cross-linked polyethylene bearings have reduced the risk of revision after THA dramatically, especially in younger patients. Observation #3: Gathering more detailed information, such as patient reported outcomes, at least on limited samples of patients, can provide further insights. Example: Registry data demonstrate much greater variability in clinical outcomes of TKA in younger patients compared to older patients. Observation #4: Having national registries from different countries provides synergistic information. Example: Combining data from several national registries provides information on performance of femoral heads of different diameter and material that are not available from just one source. Observation #5: Registries may provide unexpected information that opens unexpected avenues for study. Example: Several registries demonstrate men have a 1.5–2 times higher risk of infection after TKA. We did not know this before. Why is this? Can we reduce it?

As an increasing number of young, active, large patients are becoming candidates for total hip replacements, there is an increasingly urgent need to identify arthroplasties that will be durable, highly functional and amenable to possible future successful revision. In an era when cemented femoral stems were the primary implant option, the concept of a surface replacement was attractive and, perhaps, appropriate. However, cementless femoral stems of many designs now provide dependable long-term fixation and excellent, near normal function in patients of all ages, sex and level of activity. However, a number of issues related to cementless stem fixation could be further improved: Optimization of load transfer to proximal femur to minimise fracture risk and maximise bone preservation; Elimination of proximal-distal mismatch concerns, including bowed femurs; Facilitation of femoral stem insertion, especially with MIS THA exposures; Facilitation of revision with implants capable of providing durable fixation for active patients. The potential benefits of short stem femoral THA implants include: Ease of insertion; Reproducibility of insertion; Avoidance of issues related to proximal-distal anatomic mismatch or variations in proximal femoral diaphyseal anatomy (e.g. femoral bowing); Facilitation of MIS surgical approaches, especially anterior exposures; Optimization of proximal femoral load transfer with consequent maximization of proximal bone preservation. The purpose of this presentation is to describe the design rationale and characteristics of short (<115mm) uncemented primary THA femoral stem, to evaluate the clinical and radiographic results of short stems and to discuss the possible drawbacks specific to the use of short stems

Peri-prosthetic fractures of the femur around a THA remain challenging injuries to treat. The Vancouver Classification helps to guide decision making, and is based on fracture location, implant fixation status, and remaining bone quality. It is critical to determine fixation status of the implant, even if surgical dislocation is necessary. Type A fractures involve the trochanters, and are usually due to osteolysis. Revision of the bearing surface and bone grafting of the lesions can be effective. Type B1 fractures occur around a well fixed stem, typically at the stem tip. Internal fixation with laterally based locked cable plates is effective. Optimising proximal fixation is important, typically with locked screws and cables. Allograft struts are probably unnecessary with modern angle stable plates. Type B2 and B3 fractures are treated with revision, either with a fully coated cylindrical or a modular fluted tapered titanium stem. Distal fixation should be optimised, while preserving vascularity to proximal bony fragments. The « internal scaffold » technique has been described with excellent results. Rarely, a proximal femoral replacement is necessary. Careful attention to detail and clear knowledge of stem fixation status is necessary for a good outcome

As the incidence of total hip arthroplasty (THA) rises, an increasing prevalence of peri-prosthetic femur fractures has been reported. This is likely due to the growing population with arthroplasties, increasing patient survival and a more active life-style following arthroplasty. It is the 3rd most common reason for THA reoperation (9.5%) and 5th most common reason for revision (5% with fracture risk after primary THA reported at 0.4%-1.1% and after revision at 2.1%-4%). High quality radiographs are usually sufficient to classify the fracture and plan treatment. Important issues in treatment include stem fixation status and fracture location relative to the stem. Additional comorbidities will also influence treatment choices, of which the most critical is the presence of infection and the quality of bone stock. The most commonly studied, and reported classification system is the Vancouver. Type A are peri-trochanteric fractures with AL at the lesser and AG at the greater trochanter. B fractures are those around the stem with B1 fractures having a well-fixed stem, B2 a loose stem with adequate bone stock, and B3 representing loose stem and inadequate bone stock. C fractures are distal to the stem. Type A) Trochanteric Fractures: These are usually associated with lysis. Displaced fractures can be managed adequately with cerclage fixation and cancellous allograft to fill osteolytic defects. Undisplaced fractures usually heal well with symptomatic treatment. Type B) Fractures Around the Stem: The B1 type has a well-fixed component and is usually treated with extramedullary fixation plus graft. Contemporary plates have been designed specifically for these fractures. Strut allograft may be used to provide a more rigid construct. Spiral and long oblique fractures can be cerclaged while short oblique or transverse fractures require fixation anterior and lateral with cable plates and cortical strut grafts. Screws can be used distal to the implant, and cables used proximally. The B2 type has a loose prosthesis but otherwise good bone stock. In this setting, the fracture line may be extended on the lateral cortex of the femur as an extended osteotomy to provide easy access for cement removal. These fractures can be managed with an extensively coated stem if rotational stability can be obtained in the distal segment. If rotational stability over a 4 cm scratch interference fit of the stem isn't possible, then a fluted tapered modular stem should be used. Strut allografts improve initial stability. The B3 type has both a loose prosthesis and poor bone stock and in the younger patient restoration of bone stock should be a priority. Bulk femoral grafts may be needed. The elderly or low functional demand patient may be treated with a proximal femoral replacement. Because of soft-tissue deficiencies, a constrained acetabular liner may be needed to prevent instability. Type C) Fractures Distal to the Stem: These usually accompany a stable stem and many fixation devices are available. Locking plates have become most popular and should be secured with cerclage wires proximally around the component with screws distally. Retrograde nails may be employed if there is adequate bone distal to the stem tip and above the fracture

Cementless stem fixation is a widely used method of stem revision in North America and elsewhere in the world. There is abundant literature in its support. Most of the reports from 1985 to 2005 related to proximally or extensively porocoated designs, the former falling into disfavor with time because of unpredictable outcomes. With few exceptions (eg S-ROM) the modularity of these designs was limited to the head/neck junction. But this generation of designs was associated with some issues such as insertional fractures, limited control of anteversion (and risk of dislocation), limited applicability in the setting of severe bone loss (Paprosky Type 4 osteolysis or Vancouver Type B3 periprosthetic fracture), as well as ongoing concern relating to severe proximal stress shielding. In the past decade we have seen the mounting use of a new design concept: tapered fluted titanium stems (TFTS), which incorporate the advantages of titanium (for less flexural rigidity), conical taper (for vertical taper-lock stability), longitudinal ribs and flutes (for rotational stability), and surface preparation which attracts bone on growth for long term fixation. Four consecutive reports from our center have documented the superiority of the TFTS in our hands, with encouraging outcomes even when dealing with severe bone loss or periprosthetic fractures. There is an increasing body of other literature which reports a similar experience. Furthermore, with increasing experience and confidence in this design, we now use a monoblock or non-modular design in greater than 95% of cases in which a TFTS is indicated at our center. This circumvents the potential drawbacks of stem modularity, including taper corrosion and taper junction fracture

A) Mastering the Art of Cemented Femoral Stem Fixation. Introduction: Fixation of cemented femoral stems is reproducible and provides excellent early recovery of hip function in patients 60–80 years old. The durability of fixation has been evaluated up to 20 years with 90% survivorship. The mode of failure of fixation of cemented total hip arthroplasty is multifactorial; however, good cementing techniques and reduction of polyethylene wear have been shown to reduce its incidence. The importance of surface roughness for durability of fixation is controversial. This presentation will describe my personal experience with the cemented femoral stem over 30 years with 3 designs and surface roughness (RA) ranging from 30–150 microinches. Results: Since 1978, three series of cemented THA have been prospectively followed using periodic clinical and radiographic evaluations. All procedures were performed by the author using the posterior approach. Excellent results were noted and Kaplan-Meier survivorship ranged from 90% to 99.5% in the best case scenario at 10–20 year follow-up. Conclusion: With a properly-designed femoral stem, good cement technique, proper cement mantle, and surface roughness of 30–40 microinches, the cemented femoral stem provides a durable hip replacement in patients 60 to 80 years of age with up to 95% survivorship at 10 to 20 years. B) Cemented Primary Acetabulum. Introduction: I am going to present a technique of cementing an all-polyethylene socket, a brief review of our clinical experience, and all-polyethylene socket design features. Since 1991, we have been using direct compression molded polyethylene sockets. The minimum thickness of polyethylene is 8 mm. We keep the socket orientation at 45 degrees of lateral opening and 15 degrees of anteversion. The preparation of the socket involves multiple fixation holes with Midas Rex. The bone is cleaned with water lavage and heated cement. Radiographic Features: The cement/bone interface has been classified into three types on radiographs. Type 1 has a perfect merge of the cement into the cancellous bone in all three zones. Type III interface shows radiolucency in one or more zones. A commonly asked question is, “is this technique reproducible?” The answer is yes. Our Data: We have looked at our all-polyethylene socket from 1992 to 1998 and the total number of hips are over 1,000, with a follow-up of 2–8 years. We have not revised a single socket for fixation failure. Summary: A cemented socket is indicated in patients 60 years and older with a diagnosis of osteoarthritis. Relative contraindications are excessive bleeding, extensive cyst formation, weak cancellous bone such as in rheumatoid, JRA, DDH, and protrusion patients. Cemented THA in patients 60 years and older with DJD and molded all-polyethylene cup have provided the best results in terms of a high degree of reproducibility, high quality of function, and durability

Background. Cementless short stems have the advantages of easy insertion, reduced thigh pain and being suitable for minimally-invasive surgery, therefore cementless short stem implants have been becoming more widely used. The revelation microMAX stem is a cementless short stem with a lateral flare design that allows for proximal physiological load transmission and more stable initial fixation. Images acquired with T-smart tomosynthesis using a new image reconstruction algorithm offer reduced artifacts near metal objects and clearer visualization of peri-implant trabeculae. Therefore, these images are useful for confirming implant fixation status after total hip arthroplasty (THA). We believe that T-smart tomosynthesis is useful for estimating the condition of microMAX stem fixation and will hereby report on observation of the postoperative course of microMAX stem. Materials and Methods. Subjects comprised 19 patients (20 hips) who underwent THA using micro MAXstem between July 2012 and November 2014 (males: 7, females: 12, mean age: 67 years, ranging from 38 to 83 years). Four patients had femoral head necrosis and 15 patients had osteoarthritis of the hip. All patients continuously underwent anterior-posterior and lateral view X-ray examination and an anterior-posterior T-smart tomosynthesis scan after the operations. Results. No stem loosening was noted in any subjects. X-ray images taken over time indicated spot welds in 12 hips (60%), while T-smart tomosynthesis showed spot welds in 19 hips (95%). Furthermore, reactive radiodense lines (tensile area) were noted on X-ray images of eight hips (40%), whereas they were detected by T-smart tomosynthesis in 10 hips (50%). A prominent reactive line around the tip of the stem was noted on X-ray images in three hips (15%), and this was detected by T-smart tomosynthesis in four hips (20%). Discussion. Compared to X-ray examination, T-smart tomosynthesis made it possible to perform detailed confirmation of trabecular structure. In this series, spot welds were confirmed in the proximal load area according to the micro MAXstem design concept. Tomosynthesis images of trabeculae and trabecular structure can be confirmed in more detail than X-ray or computed tomography images. This information is beneficial for understanding the state of load transmission and implant fixation. Conclusions. The addition of tomosynthesis to micro MAXstem postoperative evaluation made it possible to accurately grasp the state of fixation between implant and bone

Over a four year period of time, 142 consecutive hip revisions were performed with the use of an extended proximal femoral osteotomy. Twenty patients had insufficient follow-up or were followed elsewhere and were excluded from the review. The remaining 122 revisions included 83 women and 39 men. Average age at time of revision was 63.8 (26–84) years. Indications for revision were aseptic loosening (114), component failure (4), recurrent dislocation (2), femoral fracture (1) and second stage re-implantation for infection (1). The extended proximal femoral osteotomy gave easy access to the distal bone-cement or bone prosthesis interface in all cases. It allowed neutral reaming of the femoral canal and implantation of the revision component in proper alignment. Varus remodeling of the proximal femur secondary to loosening was handled with relative ease implementing the osteotomy. Average time from the beginning of the osteotomy procedure to the complete removal of prosthesis and cement was 35 minutes. There were no non-unions of the osteotomised fragments at an average post-operative follow-up of 2.6 years with no cases of proximal migration of the greater trochanteric fragment greater than 2 mm, there was evidence of radiographic union of the osteotomy site in all cases by 3 months. Stem fixation with bone ingrowth was noted in 112 (92%) of 122 hips, stable fibrous fixation was seen in 9 (7%) and 1 stem was unstable and was subsequently revised. However, there was an incidence of 7% perforation rate of the femoral canal distal to the osteotomy site during cement removal. This was most prevalent where there was greater than 2 cm of cement plug present which was well bonded. When OSCAR was used instead of hand tools or power reamers, there were no perforations in 51 cases. There has been no failure of fixation with fully porous coated stems inserted in the canals where OSCAR had removed cement. Also, the use of OSCAR has allowed us to shorten the osteotomy, thus allowing a longer, intact isthmus to remain so that shorter stems can be used. We highly recommend the use of OSCAR in conjunction with the extended osteotomy for removal of well-fixed distal cement beyond the extended osteotomy site

The use of stems in revision TKA enhances implant stability and thus improves the survival rate. Stemmed components obtain initial mechanical stability when there is deficient metaphyseal bone. However the optimal method of stem fixation remains controversial, which includes selection of stem size, length or the use of cemented vs. cementless stems. Although postulated by many surgeons, there is no sufficient evidence, that cementless or hybrid fixation does perform better in the long term outcome, than cemented stems. In addition a number of studies, even from the U.S., suggested that there might be a benefit for the long term survival for cemented stems in revision TKA. Obviously cemented stems have some few advantages in revision set up as: topic antibiotic delivery and initial strong fixation. While main disadvantages arise during limited/poor bone quality for initial cancellous bone-cement fixation; revision with removal of a long cement mantle and re-cementing into a previously cemented canal. Furthermore removing a fully cemented implant can be much more time consuming. The Endo Klinik has currently over 30 years of experience utilising cemented stems in combination with a rotating hinge implant in revision TKA, including satisfactory long-term results. However we are aware of this technique associated limitations, including aseptic loosening and further conversion to a re-revision with necessary impaction bone grafting. Generally it has to be mentioned, that type of stem and reconstruction type if often driven by surgeons own and institutional preference

Background. Modular component options can assist the surgeon in addressing complex femoral reconstructions in total hip arthroplasty (THA) by allowing for customization of version control and proximal to distal sizing. Tapered stem fixation has a proven excellent track record in revision THA. Early reports by Cherubino et al. (Surg Technol Int 2010) 65 revision THA with an average follow up of 109 months (range, 76–131) demonstrate satisfactory integration in 100% of cases. Rodriguez et al.(J Arthroplasty 2009) report 96% survival in 102 revision THA at nearly 4 years average follow up. We review the early clinical results of a modular tapered femoral revision system. Methods. A query of our practice's arthroplasty registry revealed 60 patients (61 hips) who signed an IRB-approved general research consent allowing retrospective review, and underwent THA performed with the modular femoral revision system between December 2009 and April 2012. There were 35 men (58%) and 25 women (42%). Mean age was 65.1 years (range, 35–94) and BMI was 31.3 kg/m2 (range, 14–53). Procedures were complex primary in 1 hip, conversion in 6 (10%), revision in 32 (53%), and two-staged exchange for infection in 22 (33%). Two-thirds of the procedures included complete acetabular revision (n=40), while 31% (19) involved liner change only and 2 were isolated femoral revisions. Results. At an average follow-up of 1.5 years (maximum: 3.7 years) there have been no revisions or failures of the femoral component. Average Harris hip scores (0 to 100 possible) improved from 44.2 preoperatively to 66.0 at most recent evaluation, while the pain component (0 to 44 possible) improved from 15.8 to 31.2. Complications requiring surgical intervention included intraoperative periprosthetic femur fracture in one patient returned to the operating suite same day for open reduction internal fixation, which further required incision and debridement for superficial infection at 1 year postoperative; and two patients with dislocation and fracture of the greater trochanter treated with open reduction, revision of the head and liner, and application of cerclage cables, one of which required removal of a migrated claw 10 months later followed 2 weeks subsequently with incision and debridement for a non-healing wound. Postoperative radiographs were available for review for 59 THA in 58 patients. Analysis of the femoral component revealed satisfactory findings in 50 hips (85%) while 9 had radiographic changes that included bone deficit, osteolysis, or radiolucency in one or more zones. Conclusions. The early results of this modular femoral revision system are promising for the treatment of the deficient femur in complex primary and revision total hip arthroplasty. Patients with radiographic changes are advised to return for regular clinical and radiographic follow-up. Survival of the modular femoral component in this series was 100% at mean follow-up of 1.5 years and up to 3.7 years. While Harris hip clinical and pain scores were somewhat low at most recent evaluation, they were significantly improved over preoperative levels

Aims

The aim of this study was to determine whether total hip arthroplasty (THA) for chronic hip pain due to unilateral primary osteoarthritis (OA) has a beneficial effect on cognitive performance.

As an increasing number of young, active, large patients are becoming candidates for total hip replacements, there is an increasingly urgent need to identify arthroplasties that will be durable, highly functional and amenable to possible future successful revision. In an era when cemented femoral stems were the primary implant option, the concept of a surface replacement was attractive and, perhaps, appropriate. However, cementless femoral stems of many designs now provide dependable long-term fixation and excellent, near normal function in patients of all ages, sex and level of activity. However, a number of issues related to cementless stem fixation could be further improved: Optimisation of load transfer to proximal femur to minimise fracture risk and maximise bone preservation; Elimination of proximal-distal mismatch concerns, including bowed femurs; Facilitation of femoral stem insertion, especially with MIS THA exposures; Facilitation of revision with implants capable of providing durable fixation for active patients. The potential benefits of short stem femoral THA implants include: Ease of insertion; Reproducibility of insertion; Avoidance of issues related to proximal-distal anatomic mismatch or variations in proximal femoral diaphyseal anatomy (e.g. femoral bowing); Facilitation of MIS surgical approaches, especially anterior exposures; Optimisation of proximal femoral load transfer with consequent maximisation of proximal bone preservation. The purpose of this presentation is to describe the design rationale and characteristics of short (< 115mm) uncemented primary THA femoral stem, to evaluate the clinical and radiographic results of short stems and to discuss the possible drawbacks specific to the use of short stems

Cementless stem fixation is a widely used method of stem revision in North America and elsewhere in the World. There is abundant literature in its support. Most of the reports from 1985 to 2005 related to proximally or extensively porocoated designs, the former falling into disfavor with time because of unpredictable outcomes. With few exceptions (eg S-ROM) the modularity of these designs was limited to the head/neck junction. But this generation of designs was associated with some issues such as insertional fractures, limited control of anteversion (and risk of dislocation), limited applicability in the setting of severe bone loss (Paprosky Type 4 osteolysis or Vancouver Type B3 periprosthetic fracture), as well as ongoing concern relating to severe proximal stress shielding. In the past decade we have seen the mounting use of a new design concept: tapered fluted titanium stems (TFTS), which incorporate the advantages of titanium (for less flexural rigidity), conical taper (for vertical taper-lock stability), longitudinal ribs and flutes (for rotational stability), and surface preparation which attracts bone on growth for long term fixation. Four consecutive reports from our center have documented the superiority of the TFTS in our hands, with encouraging outcomes even when dealing with severe bone loss or periprosthetic fractures. There is an increasing body of other literature which reports a similar experience. Furthermore, with increasing experience and confidence in this design, we now use a monoblock or non-modular design in greater than 95% of cases in which a TFTS is indicated at our center. This circumvents the potential drawbacks of stem modularity, including taper corrosion and taper junction fracture

Vancouver A: If minimal displacement and prosthesis stable can treat nonoperatively. If displacement is unacceptable and/or osteolysis is present consider surgery. AL: Rare, avulsions from osteopenia and lysis. If large, displaced and include large portion of calcar-can destabilise stem and prompt femoral revision. AG: More common. Often secondary to lysis. Does not usually affect implant stability. Minimal displacement. Treat closed × 3 months. Revise later is needed to remove the particle generator, debride defects and bone graft. Displaced with good host bone stock. Consider early ORIF and bone grafting. Vancouver B:. B1: Rarely non-operative. ORIF with femoral component retention. Need to carefully identify stem fixation. B2's classified as B1's are doomed to fail. B1's correctly identified treated with plate, allograft struts or both. High union rates with component retention. B2: Femoral revision +/− strut allograft. Best results seen with patients revised with uncemented, extensively porous coated femoral stems. May use modular, fluted taper stems. B3: Proximal femoral replacement - Tumor prosthesis, Allograft Prosthetic Composite (APC). Uncemented femoral stem - Extensively porous coated, Fluted, tapered stem, Allograft strut. Vancouver C: Treat with standard fracture techniques. These fractures are away from the femoral prosthesis. Rarely nonoperative. Fixation options – Cerclage, Strut Allograft, Plate fixation, Retrograde IM nail, or a Combination thereof. Avoid stress risers between implants. Bypass (overlap) fixation. Consider allowing 2.5 cortical diameters between devices