Background

There are no published studies investigating predictive values of psychological distress on effectiveness of epidural injection.

In selected patients in-cement revision of the total hip arthroplasty components is an attractive option. Recommended roughening of the primary mantle surface remains controversial. Aim of the study was to investigate the influence of the cement surface roughening on the strength of bilaminar cement interface.

Flat, laboratory model of bilaminar cement interface was used. Prior to its creation, modeled primary mantle surface was machined to the roughness of either smooth surface observed after removal of a highly polished stem (Ra=200nm) or that following roughening (Ra=5μm). Two viscosities of interfering fluids (water and bone marrow) were also used. 6 variants (smooth or rough, both stained with water, bone marrow or with no fluid) with 7 repeats were exposed to single shear to failure.

No significant difference in resistance to shear was observed between the groups with dry smooth (16.82MPa) and rough surfaces (16.96MPa), and those stained with large volume of low viscosity fluid. In the presence of water, roughening did not significantly influence the interface (smooth – 17.04MPa and rough – 16.25MPa respectively).

In the smooth variant with large volume of viscous fluid, ultimate stress value dropped to 5.53MPa, and 9.87MPa in the roughened group with the same amount of viscous fluid (p< 0.05).

Extra roughening may offer some benefit when performing in-cement revision in the presence of large volume of viscous fluid only though in-cement revision would not be then recommended. In the presence of low viscosity fluids (blood, irrigation fluid) benefit of roughening is dubious.

During hip revision removal of old cement mantle is a major problem. In cases of satisfactory bond between cement mantle and the underlying bone, cementing the revision stem into the old mantle is regarded as a highly attractive option. The aim was the analysis of the shearing strength of the interface between two layers of poly-methylmethacrylate cement in the presence of fluid.

A laboratory, two-dimensional model of the interface was used. Effect of different viscosity fluids and volumes on its strength was checked. 6 variants (control monoblock, dry surface, surface stained with small or large volume of water or highly viscous fluid) containing 7 repeats were exposed to a single shearing stress to failure.

Large volume of viscous fluid prevented bonding completely in two cases and significantly weakened the other samples showing mean failure stress of 5.53 MPa. This was significantly lower compared with control monoblock (19.8MPa), dry surface variant (16.9MPa) and the stain with small amount high viscosity fluid (16.01MPa). Interestingly, presence of a large volume of low viscosity fluid did not significantly reduce resistance to shear stress (17.05MPa).

In all but large volume of viscous fluid variants, the failure occurred away from the interface between two cement layers. Large amount of viscous fluid weakened significantly this interface. If such a viscous fluid could be eliminated by copious water irrigation it is likely that strength of the cement-cement bond will be maintained. Our observations suggest that cement-in-cement technique seems to be biomechanically acceptable

Background: During cemented hip arthroplasty revision removal of all the old cement mantle is a time staking process with multiple disadvantages. In some selected patients cementing revision stem into the old mantle is regarded as a highly attractive option. Contradictory evidence exists whether bond between two cement layers is strong enough, especially in the presence of interfering fluids.

Aim: analysis of the shearing strength of the interface between two layers of polymethylmethacrylate cement in the presence of fluid.

Methods: Cylindrical blocks of polymethylmethacrylate cement represented primary cement mantle. Its flat surface was machined to reproduce smooth old cement mantle surface comparable with that after removal of a highly polished stem (Ra=200nm). A second block was cast against the first and their junction represented the investigated interface. The influence of fluid was examined by injecting liquid onto the ‘primary’ surface prior to casting. Water or 2% water solution of carboxy-methyllcellulose (representing bone marrow viscosity of 400mPas) were used in two volumes: 0.02ml/cm2 (small) or 0.4ml/cm2 (large - surface submerged).

6 variants (control monoblock, dry surface, surface stained with small or large volume of water or highly viscous fluid) containing 7 repeats were exposed to a single shearing stress to failure at the speed of 1mm/min (Autograph AGS, Shimadzu, Japan).

Results were analyzed using 1-way ANOVA with post-hoc analysis (equal N HSD) and power calculations.

Results: Large volume of viscous fluid prevented bonding completely in two cases and significantly weakened the other samples showing mean failure stress of 5.53 MPa (95%CI:1.33–9.73 MPa). This was significantly lower compared with control monoblock (19.8–95% CI: 17.8–21.9 MPa), dry surface variant (16.9–95% CI: 15.9–18.0 MPa) and that stained with small amount of high viscosity fluid (16.01–95% CI: 15.12–17.0 MPa). Interestingly, presence of a large volume of low viscosity fluid (water) did not significantly reduce resistance to shear stress (17.05 – 95% CI:15.67–18.43 MPa).

Similar relations were observed when strain at failure and toughness were analyzed.

Conclusions: In all but large volume of viscous fluid variants, the failure occurred away from the interface between two cement layers. Large amount of viscous fluid weakened significantly this interface. If such a viscous fluid can be eliminated by copious water irrigation it is likely that strength of the cement-cement bond will be maintained. In the presence of low viscosity fluids (water, blood) careful use of gun technique is likely to allow for their escape as the cement is advanced within the femoral or the old mantle canal leading to a satisfactory bond. Our observations suggest that cement-in-cement technique seems to be biomechanically acceptable.

Comparison of the safety and efficacy of Bilateral Simultaneous Total Hip Arthroplasty (BSTHA) with that of staged (SgTHA) and unilateral (UTHA) was conducted using DerSimonian–Laird heterogeneity meta-analysis. Twenty three citations were eligible for inclusion. A total of 2063 BSTHA patients were identified. Meta-analysis of homogenous data revealed that there were no statistically significant differences between rates of thromboembolic events (p=0.268 and p=0.356) and dislocation (p=0.877) when comparing SgTHA or UTHA versus BSTHA procedures. Systematic analysis of heterogenous data demonstrated that mean length of stay was shorter in BSTHA as compared to SgTHA and UTHA procedure, blood loss was lower in BSTHA in all studies except one, whilst the surgical time was not different between groups. BSTHA was also found to be economically and functionally efficacious.