Recent concerns over adverse effects of metal ion release, have led to the development of alternative hip joint replacements. This study reports the performance of new hemispherical MOTIS® (milled pitch-carbon fibre reinforced polyetheretherketone) acetabular cups articulating against Biolox Delta® femoral heads with the aim of producing lower wear and more biologically compatible bearings. The wear performance of 40mm hemispherical MOTIS® cups articulating against Biolox Delta® heads has been investigated. The diametral clearance was 322±15.3nm (mean ± standard deviation). Wear tests were carried out on the Simplified Mark II Durham Hip Wear Simulator to 8 million cycles. New born bovine calf serum was used as the lubricant, diluted to give a protein content of 17g/l. Friction tests were carried out on the unworn joints and worn joints after 7.5 million cycles using lubricants containing protein (bovine serum based carboxymethyl cellulose (CMC) fluids) and without protein (water based CMC fluids). Temperature measured near every hip joint over a continuous wear testing period of 0.5 million cycles was recorded using PICO TC-08 data logger. One K-type thermocouple was placed carefully and consistently in each wear station and two were used to record the ambient room temperature. After stopping the wear test, the data logger continued recording the temperature for a further ten hours to indicate the cooling period. Additionally surface analyses were undertaken before and after wear testing using a non-contacting profilometer and atomic force (AFM) microscope.Introduction
Materials and Methods
Ultra-high molecular weight polyethylene (UHMWPE) has been the gold standard material of choice for the load-bearing articulating surface in knee joint prostheses. However, the application of joint replacements to younger (aged < 64 years) and more active people plus the general increase in life expectancy results in an urgent need for a longer lasting material with better in-use performance. There are three major material related causes that can lead to joint failure in UHMWPE knee joint replacements: free radical induced chemical degradation; mechanical degradation through wear and delamination; and UHMWPE micron and submicron wear debris induced osteolysis. As a potential solution to these problems, highly crosslinked UHMWPE stabilised with infused antioxidant vitamin E (α-Tocopherol), which is abbreviated as E-Poly, has been of great interest. In the current work, the wear performance and mechanical properties of Vanguard cruciate retaining (CR) E-Poly tibial inserts were assessed and compared with Vanguard CR Arcom tibial inserts. Also E-Poly plates were compared with direct compression moulded UHMWPE wear plates. Both a multi-directional pin-on-plate tester and a six-station Prosim (Manchester, UK) knee wear simulator were used to assess wear properties of E-Poly plates and E-Poly tibial inserts respectively. All E-Poly plates and tibial inserts were sterilised and vacuum packed in the same way as Vanguard implants before wear testing. The wear knee simulator test was conducted in accordance with ISO 14243-3:2004 with the exception that a more aggressive Tibial Rotation and Anterior/Posterior displacement profiles, based on the kinematics of the natural knee were incorporated. Under the same aggressive pre-clinical wear testing condition, compared with Vanguard Arcom CR tibial inserts, Vanguard E-Poly CR tibial inserts experienced an 85% reduction in the mean wear rate. The former had a mean wear rate of 6.51±1.75 mm3 per million cycles (MC) and the latter had a mean wear rate of 0.96±0.11 mm3/MC over the 7 million cycle testing period. A similar reduction (80%±8.5) in the mean wear factor was also observed on E-Poly plates compared with a series of direct compression moulded GUR1050 UHMWPE plates processed under a range of manufacturing processing conditions. Wear testing was conducted with a configuration of flat-ended stainless steel indenters multi-directionally sliding against the UHMWPE plates. Mechanical properties on Vanguard Arcom UHMWPE and E-Polys were evaluated using the small punch test. All tests were carried out using an Instron 5565 Universal Testing System at a constant crosshead speed of 0.5mm/min. With regard to work-to-failure, no statistical difference was observed, with the former being 254.2±4.1 mJ and the latter 255.6±28.2 mJ. However, all E-Polys exhibited strain stiffening due to the stretch of crosslinks. This resulted in a In conclusion, we have found that Vitamin E Stabilised UHMWPE tibial inserts are promising for knee joint prostheses. However, further investigations are needed to address potential issues such as the particle size and size distribution of E-Poly wear debris and the associated reactivity.
Artificial hip joints have been in use for a number of years; various combinations of metals and polymers have been tested both in vitro and in vivo. Modern ceramics have found application as bearings in hip replacement due to the enhanced wear and friction that they offer. It has been hypothesised that during the swing phase of gait it is possible for the Femoral head and the Acetabular cup to dislocate, before relocating during heel contact. Severe loading such as this could cause greater levels of wear to occur in artificial hip joints. This study provides comparative analysis between ceramic-on-ceramic hip joint pairings under both severe and standard loading profiles. Five zirconia-toughened alumina (ZTA) 28mm diameter bearing pairs were tested on a ProSim Hip Simulator for 5.3 million cycles (MC), two under severe loading and three under standard loading conditions. Additionally a Loaded Soak Control, Soak Control and Environmental Control were used. Wear was recorded every 0.5 MC by gravimetric measurement. Surface microscopy images from a Zygo New View 100 and an Atomic Force Microscope (AFM) were taken before testing and then at, 0.5 MC. 2.5 MC, and 5.3 MC. The standard loading profile followed Wear rates for the ceramic cups under severe wear condition were found to be 0.0356±0.0059mm3/ MC and for the standard wear condition to be 0.0178±0.0049mm3/MC. The femoral heads had wear rates of 0.0164±0.0046mm3/MC for severe wear condition and no wear was detected for the standard wear condition. The results of the present study showed almost no wear under standard gait condition and only a modest increase in wear occurred when using severe wear condition. Thus the resulting wear rates are still significantly lower than those found for alumina-alumina total hip joints [
