As the number of younger and more active patients treated with total knee arthroplasty (TKA) continues to increase, consideration of better fixation as a means of improving implant longevity is required. Cemented TKA remains the reference standard with the largest body of evidence and the longest follow-up to support its use. However, cementless TKA, may offer the opportunity of a more bone-sparing procedure with long lasting biological fixation to the bone. We undertook a review of the literature examining advances of cementless TKA and the reported results.

Cite this article: Bone Joint J 2016;98-B:867–73.

A retrospective review was performed of patients undergoing primary cementless total knee replacement (TKR) using porous tantalum performed by a group of surgical trainees. Clinical and radiological follow-up involved 79 females and 26 males encompassing 115 knees. The mean age was 66.9 years (36 to 85). Mean follow-up was 7 years (2 to 11). Tibial and patellar components were porous tantalum monoblock implants, and femoral components were posterior stabilised (PS) in design with cobalt–chromium fibre mesh. Radiological assessments were made for implant positioning, alignment, radiolucencies, lysis, and loosening. There was 95.7% survival of implants. There was no radiological evidence of loosening and no osteolysis found. No revisions were performed for aseptic loosening. Average tibial component alignment was 1.4° of varus (4°of valgus to 9° varus), and 6.2° (3° anterior to 15° posterior) of posterior slope. Mean femoral component alignment was 6.6° (1° to 11°) of valgus. Mean tibiofemoral alignment was 5.6° of valgus (7° varus to 16° valgus). Patellar tilt was a mean of 2.4° lateral (5° medial to 28° lateral). Patient satisfaction with improvement in pain was 91%. Cementless TKR incorporating porous tantalum yielded good clinical and radiological outcomes at a mean of follow-up of seven-years.

Cite this article: Bone Joint J 2014;96-B(11 Suppl A):87–92.

This video presentation serves to illustrate the pertinent aspects of bone preparation and implant insertion in cementless total knee arthroplasty (TKA) utilizing porous tantalum as a fixation surface integral to the success of the procedure.

The patient is typical of the surgical candidate frequently encountered for arthroplasty—a 60-year-old female with three compartment osteoarthritis of the knee, and manifesting a 10-degree varus deformity and 5-degree flexion contracture. She is a limited community ambulator without the use of support.

A standard surgical exposure is utilised and the bone preparation is identical to that used in the fixation of cemented implants—no alignment guides, cutting guides, or referencing instrumentation is used that is unique in the femoral or tibial bone preparation. The principal difference is in the patellar preparation. Instrumentation unique to the cementless porous tantalum patella is utilised in order to achieve three goals: a composite implant/residual bone thickness that replicates the thickness of the native patella, the generation of a planar patellar resection that is parallel to the anterior cut of the femur, and secure initial stability of fixation.

Keys to the initial fixation of the porous tantalum tibial and patellar components include the high surface friction of the material against bone, as well as the interference between the hexagonal pegs of each implant within the fixation holes (which are dimensionally smaller in diameter than the major and minor dimensions of the peg geometry). Care must be instituted to ensure that no bone or soft tissue debris is interposed at the mating surfaces of the implants that would compromise interface contact, and to carefully suction the peg holes to ensure that no debris impedes the complete seating of the pegs and the prosthesis. Lastly, all mating surfaces at the implant/bone interface must approach each other in a parallel fashion to optimise contact between the fixation surfaces and the bone resection surfaces.

The procedure is simply, easily performed, and is time saving. Total elapsed time for insertion of all three TKA implants in this video is 90 seconds.

Introduction. The ideal type of total knee arthroplasty (TKA) prosthesis remains a debatable topic with many different options available. Uncemented TKA has been a viable option due to its decreased operating room (OR) time but also because of its proposed improved long term fixation. Unfortunately, in the past uncemented TKA was associated with increased blood loss. Surgical technique and perioperative treatments have changed since these original studies and tranexamic acid (TXA) has become the gold standard for TKA blood loss management. The objective of this study was to evaluate if there was a difference in hemoglobin and hematocrit change, along with blood loss volume during surgery between cemented and cementless TKA when modern blood loss techniques are utilized. Methods. We retrospectively reviewed data from TKAs performed by three high volume surgeons between 2016 and 2019. We excluded bilateral TKA, revisions, hardware removal intraoperatively and other indications for TKA than primary OA. Power analysis determined 85 patients in both the cementless and cemented TKA groups. Patients were matched 1:1 for age, sex, BMI and surgeon. Use of TXA, intraoperative blood loss, differences in hemoglobin and hematocrit pre- and postoperatively days one, two, and three were recorded. Continuous variables were analyzed using T-tests and categorical variables were evaluated using Chi-squared tests. Results. No significant difference was observed between the cementless and cemented groups for hemoglobin (p=0.214), hematocrit (p=0.164), or intraoperative blood loss volume (p=0.343). A trend towards significantly shorter OR time was seen in the cementless group (p = 0.058). Conclusion. With modern TKA surgery, including the use of TXA, there is no difference in perioperative blood loss between cemented and cementless TKA. Unlike previous studies, the use of modern blood loss salvage techniques in conjunction with cementless TKA fixation, does not result in more blood loss during the perioperative period

Aims. Cementless total knee arthroplasty (TKA) offers the potential for strong biological fixation compared with cemented TKA where fixation is achieved by the mechanical integration of the cement. Few mid-term results are available for newer cementless TKA designs, which have used additive manufacturing (3D printing). The aim of this study was to present mid-term clinical outcomes and implant survivorship of the cementless Stryker Triathlon Tritanium TKA. Methods. This was a single institution registry review of prospectively gathered data from 341 cementless Triathlon Tritanium TKAs at four to 6.8 years follow-up. Outcomes were determined by comparing pre- and postoperative Knee Injury and Osteoarthritis Outcome Score for Joint Replacement (KOOS JR) scores, and pre- and postoperative 12-item Veterans RAND/Short Form Health Survey (VR/SF-12) scores. Aseptic loosening and revision for any reason were the endpoints which were used to determine survivorship at five years. Results. At mid-term follow-up, the mean KOOS JR score improved significantly from 33.14 (0 t0 85, standard deviation (SD) 21.88) preoperatively to 84.12 (15.94 to 100, SD 20.51) postoperatively (p < 0.001), the mean VR/SF-12 scores improved significantly from physical health (PH), 31.21 (SD 5.32; 23.99 to 56.77) preoperatively to 42.62 (SD 10.72; 19.38 to 56.82) postoperatively (p < 0.001) and the mental health (MH), 38.15 (SD 8.17; 19.06 to 60.75) preoperatively to 55.09 (SD 9.64; 19.06 to 66.98) postoperatively (p < 0.001). A total of 11 revisions were undertaken, with an overall revision rate of 2.94%, including five for periprosthetic joint infection (1.34%), three for loosening (0.80%), two for instability (0.53%), and one for pain (0.27%). The overall survivorship was 97.06% and survivorship for aseptic loosening as the endpoint was 98.40%, with a 99.5% survivorship of the 3D-printed tibial component. Conclusion. This 3D-printed cementless total knee system shows excellent survivorship at mid-term follow-up. This design and the ability to obtain cementless fixation offers promise for excellent long-term durability. Cite this article: Bone Joint J 2021;103-B(6 Supple A):32–37

Aims

The use of cementless total knee arthroplasty (TKA) components has increased during the past decade. The initial design of cementless metal-backed patellar components had shown high failure rates due to many factors. The aim of this study was to evaluate the clinical results of a second-generation cementless, metal-backed patellar component of a modern design.

Aims

This study aimed to investigate the optimal sagittal positioning of the uncemented femoral component in total knee arthroplasty to minimize the risk of aseptic loosening and periprosthetic fracture.

Aims

The primary objective of this registry-based study was to compare patient-reported outcomes of cementless and cemented medial unicompartmental knee arthroplasty (UKA) during the first postoperative year. The secondary objective was to assess one- and three-year implant survival of both fixation techniques.

Aims

This study aims to determine the rate of and risk factors for total knee arthroplasty (TKA) after operative management of tibial plateau fractures (TPFs) in older adults.

Introduction. Cementless TKA offers the potential for strong fixation through biologic fixation technology as compared to cemented TKA where fixation is achieved through mechanical integration of the cement. Few mid-term results are available for newer cementless TKA designs that have used additive manufacturing (3-D printing) for component design. The purpose of this study is to present minimum 5-year clinical outcomes and implant survivorship of a specific cementless TKA using a novel 3-D printed tibial baseplate. Methods. This is a single institution registry review of the prospectively obtained data on 296 cementless TKA using a novel 3-D printed tibial baseplate with minimum 5-year follow-up. Outcomes were determined by comparing pre- and post-operative Knee Injury and Osteoarthritis Outcome Score for Joint Replacement (KOOS JR) scores and pre- and post-operative 12 item Veterans RAND/Short Form Health Survey (VR/SF-12). Aseptic loosening as well as revision for any reason were the endpoints used to determine survivorship at 5 years. Results. At minimum 5-year follow-up, the KOOS JR score improved from 34.88 pre-operatively to 84.29 post-operatively (p-values = 0.0001), the VR/SF-12 scores improved from PH − 31.98 pre-operatively to 42.80 post-operatively (p-values = 0.0001) and the MH − 37.24 pre-operatively to 55.16 post-operatively (p-value = 0.0001). Eleven revisions were performed for an overall revision rate of 2.94% - including 5 PJI (1.34%), 3 loosening (0.80%), 1 instability (0.27%), 2 pain (0.53%). The overall 5-year survivorship was 97.1% and survivorship for aseptic loosening as the endpoint was 98.40%. The survivorship of the 3-D printed porous tibial component was 99.2%. Conclusion. This 3-D printed tibial baseplate and cementless total knee system shows excellent survivorship at 5-year follow-up. The design of this implant and the ability to obtain cementless fixation offers promise for excellent long-term durability

Over the past 30 years, cemented, cementless, and hybrid fixation options have been utilised with various total knee arthroplasty (TKA) implant systems. While cemented components are widely used and considered the most reliable method of fixation, historical results may not be applicable to contemporary patients, who are increasingly younger than 65 years of age. Moreover, the literature is not definitive on which method of TKA fixation obtains the best clinical, functional, and radiographic results. A recent Cochrane meta-analysis on roentgen stereophotogrammetric analysis (RSA) included five randomised clinical trials (RCTs) in 297 participants. The authors observed that cemented fixation of tibial components demonstrated smaller displacement in relation to cementless fixation. However, the risk of future aseptic loosening with uncemented fixation was approximately half that of cemented fixation (risk ratio = 0.47, 95% CI 0.24 to 0.92) with a 16% absolute risk difference between groups. Almost all included studies recorded functional measures of Knee Society and Hospital for Special Surgery knee scores, but the authors of each study found no significant difference between the groups. Recently, highly porous metals have become an attractive fixation option in TKA due to their biomechanical properties. In a large RCT of 397 patients, Pulido et al found that uncemented highly porous metal tibias provided comparably durable fixation and reliable pain relief and restoration of function when compared with traditional cemented modular tibias. While longer term studies are needed, cementless TKAs may be a durable and reliable alternative with highly porous metals, particularly in younger patients

Over the past 30 years, cemented, cementless, and hybrid fixation options have been utilised with various total knee arthroplasty (TKA) implant systems. While cemented components are widely used and considered the most reliable method of fixation, historical results may not be applicable to contemporary patients, who are increasingly younger than 65 years of age. Moreover, the literature is not definitive on which method of TKA fixation obtains the best clinical, functional, and radiographic results. A recent Cochrane meta-analysis on roentgen stereophotogrammetric analysis (RSA) included five randomised clinical trials (RCTs) in 297 participants. The authors observed that cemented fixation of tibial components demonstrated smaller displacement in relation to cementless fixation. However, the risk of future aseptic loosening with uncemented fixation was approximately half that of cemented fixation (risk ratio = 0.47, 95% CI 0.24 to 0.92) with a 16% absolute risk difference between groups. Almost all included studies recorded functional measures of Knee Society and Hospital for Special Surgery knee scores, but the authors of each study found no significant difference between the groups. Recently, highly porous metals have become an attractive fixation option in TKA due to their biomechanical properties. In a large RCT of 397 patients, Pulido et al found that uncemented highly porous metal tibias provided comparably durable fixation and reliable pain relief and restoration of function when compared with traditional cemented modular tibias. While longer-term studies are needed, cementless TKAs may be a durable and reliable alternative with highly porous metals, particularly in younger patients

Critical review of the literature fails to make a convincing case for use of cement in TKA. Many studies demonstrate clinical, mechanical, and biological failure when cement is used for fixation. Work by Ryd et al. has shown that initial migration within the first few months diminished rapidly after the first 6 months with virtually no additional movement for years after. They also suggested that cemented components do not remain rigidly fixed to bone long-term, but loosen enough to move 0.2 to 1 mm at the bone-cement interface with provocative testing. Although bone-ingrowth tibial components migrate slightly more initially than cemented ones do, they stabilise and do not sink progressively. Screw fixation adds rigidity, but does not seem to improve results. Rigidity of initial fixation is the most important feature after alignment to ensure pain-free function after arthroplasty, and can be achieved with press-fit techniques in TKA. Several early reports of bone-ingrowth TKA had inferior results because the tibial component had no stem, peg, or screw fixation, leading to implant migration and loosening. An effective stem has been shown to greatly improve tibial component fixation. The cut upper surface of the prepared tibia has areas that are too weak to withstand the forces that are applied to the surface, and failure in compression is likely unless fixation is augmented. An effective stem also reduces the shear and tensile loads at the bone-prosthesis interface. The effectiveness of compression or compaction of the tibial cancellous bone with an appropriately sized tibial metaphyseal stem has been shown, and probably was a major factor in the long-term success of fixation in our series. Clinical results of TKA with osteointegration techniques for fixation of the femoral and tibial components in our series are comparable with the best series reported with cemented fixation. Many recent studies show significant advantages of osteointegration over cement fixation in TKA. Fixation of implants with PMMA pressed into cancellous bone eventually loosens, and fixation of a metal component to bone cement also is tenuous in most cases. Cement is disappearing rapidly from use in total hip, ankle, and shoulder arthroplasty, and soon will be replaced with osteointegration technique in the knee. Perhaps the most appealing aspect of bone-ingrowth TKA is bone preservation. The ease of revisability because of good bone was encouraging in the components that wore, loosened, or became infected in the current series of TKA. These knees are functioning as well as knees with primary TKA. Should these knees develop additional problems, progressive destruction of bone is unlikely to occur, even if repeated revision is necessary

Introduction. Restoration of a neutral mechanical axis has been a widely held tenet of primary total knee arthroplasty (TKA), however new technologies are recently being marketed which claim correction of alignment deformity is unimportant. This study was undertaken to determine whether the outcome of aseptic loosening was associated with post-operative mal-alignment of the mechanical axis. Methods. A 1:9 matched case-control analysis was conducted within a cohort of 1,030 consecutive cemented posterior stabilized TKAs with 7 to 11.5 yrs follow-up (average 9 yrs). Aseptic loosening had occurred in 10 knees (1.0%). Nine controls were randomly selected for each case within matching criteria for age and minimum time in situ. Post-operative mechanical alignment was determined using retrieved long leg radiographs. Age-adjusted relative risk was estimated using conditional logistic regression. Results. Radiographs revealed 8 of the 10 loosened cases had been placed in 3 or more degrees varus mechanical alignment (range, 2? varus to 7? varus), compared to only 4 of the 90 age-matched controls (range, 4? valgus to 4? varus). A single degree change of mechanical alignment in the varus direction was associated with a more than 4-fold increase of risk of loosening (odds ratio 4.6, 95% confidence interval 1.7–12.7; p=0.0035). The relative risk for mechanical alignment >= 3? varus compared to <= 2? varus (dichotomous) was 69.2 (95% confidence interval 8.1–589; p=.0001). BMI, gender, and pre-op deformity were not significant. Discussion. These results suggest that avoidance of varus postoperative alignment is an extremely important determinant of TKA fixation durability

The initial application of bone ingrowth technology to the fixation of total knee arthroplasty (TKA) components without bone cement was based on the premise that bone cement was “not biologic”, and so over time would undergo fatigue failure with subsequent loosening. It was hoped that this problem could be obviated by cementless fixation by bone ingrowth, which would remodel over time and not fatigue. In addition, it was anticipated that the failed cementless TKA might be easier to revise and leave the surgeon with more bone to work with. Whether or not cementless fixation of TKA components was justified on any of these counts was uncertain through the first 2 decades of their use. Much of the data accumulated during that period poorly supported these contentions, while cemented TKA was increasingly reported as a reliable, consistent and less complicated form of TKA fixation. However, over the past decade, new evidence has accumulated demonstrating greater success with this technology in several well designed studies as well as from registry studies. Most of this evidence involves the use of Porous Tantalum. However, increasing evidence that loosening of well done, well designed cemented TKA is rare along with some evidence that a certain percentage of cementless TKA patients fail to achieve stability remains concerning. In addition, no studies have justified improved longevity to the extent that the increased cost of cementless devices can be justified

Aims

Debate remains whether the patella should be resurfaced during total knee replacement (TKR). For non-resurfaced TKRs, we estimated what the revision rate would have been if the patella had been resurfaced, and examined the risk of re-revision following secondary patellar resurfacing.

Over the past 30 years, cemented, cementless, and hybrid fixation options have been utilised with various total knee arthroplasty (TKA) implant systems. While cemented components are widely used and considered the most reliable method of fixation, historical results may not be applicable to contemporary patients, who are increasingly younger than 65 years of age. Moreover, the literature is not definitive on which method of TKA fixation obtains the best clinical, functional, and radiographic results. A recent Cochrane meta-analysis on roentgen stereophotogrammetric analysis (RSA) included five randomised clinical trials (RCTs) in 297 participants. The authors observed that cemented fixation of tibial components demonstrated smaller displacement in relation to cementless fixation. However, the risk of future aseptic loosening with uncemented fixation was approximately half that of cemented fixation (risk ratio = 0.47, 95% CI 0.24 to 0.92) with a 16% absolute risk difference between groups. Almost all included studies recorded functional measures of Knee Society and Hospital for Special Surgery knee scores, but the authors of each study found no significant difference between the groups. Recently, highly porous metals have become an attractive fixation option in TKA due to their biomechanical properties. In a large RCT of 397 patients, Pulido et al. found that uncemented highly porous metal tibias provided comparably durable fixation and reliable pain relief and restoration of function when compared with traditional cemented modular tibias. While longer-term studies are needed, cementless TKAs may be a durable and reliable alternative with highly porous metals, particularly in younger patients

Two big problems exist with the all-polyethylene cemented tibial component—the polyethylene and the cement. The polyethylene is too weak and flexible to bear tibial load, so it deforms and loosens. Isoelastic material has never worked, and it never will. The interface stresses are too high when two flexible structures are poorly bonded and heavily loaded. Critical review of the literature fails to make a convincing case for use of cement in TKA. Many studies demonstrate clinical, mechanical, and biological failure when cement is used for fixation. Work by Ryd et al. has shown that initial migration within the first few months diminished rapidly after the first 6 months with virtually no additional movement for years after. They also found that cemented components do not remain rigidly fixed to bone long-term, but loosen enough to move 0.2 to 2.1 mm at the bone-cement interface with provocative testing. Although bone-ingrowth tibial components migrate slightly more initially than cemented ones do, they stabilise and do not sink progressively. Screw fixation adds rigidity, but does not seem to improve results. Rigidity of initial fixation is the most important feature after alignment to ensure pain-free function after arthroplasty, and can be achieved with press-fit techniques in TKA. Several early reports of bone-ingrowth TKA had inferior results because the tibial component had no stem, peg, or screw fixation, leading to implant migration and loosening. An effective stem has been shown to greatly improve tibial component fixation. The cut upper surface of the prepared tibia has areas that are too weak to withstand the forces that are applied to the surface, and failure in compression is likely unless fixation is augmented. An effective stem also reduces the shear and tensile loads at the bone-prosthesis interface. The effectiveness of compression or compaction of the tibial cancellous bone with an appropriately sized tibial metaphyseal stem has been shown, and probably was a major factor in the long-term success of fixation in our series. Clinical results of TKA with osteointegration techniques for fixation of the femoral and tibial components in our series are comparable with the best series reported with cemented fixation. Many recent studies show significant advantages of osteointegration over cement fixation in TKA. Fixation of implants with PMMA pressed into cancellous bone eventually loosens, and fixation of a metal component to bone cement also is tenuous in most cases. Cement is disappearing rapidly from use in total hip, ankle, and shoulder arthroplasty, and soon will be replaced with osteointegration technique in the knee. Perhaps the most appealing aspect of bone-ingrowth TKA is bone preservation. The ease of revisability because of good bone was encouraging in the components that wore, loosened, or became infected in the current series of TKA. These knees are functioning as well as knees with primary TKA. Should these knees develop additional problems, progressive destruction of bone is unlikely to occur, even if repeated revision is necessary

Purpose: The purpose of this study was to investigate the mid to long term (minimum 10 years follow-up) survivorship of the AMK total knee arthroplasty (TKA), as well as determine the effect of implant fixation on outcome. Method: Between 1988 and 2000, 1074 AMK primary total knee arthroplasties were preformed on 843 patients. All diagnosis included, the distribution was 90% osteoarthritis (971), 7% inflammatory arthritis (76) and 3% other diagnoses (27). Average time from surgery was 15 years (range 10–21 years). Average age at primary procedure was 68 years (range 22–99). Fifty-six percent were female (599) and 44% male (475). Preoperative alignment consisted of 56% varus (601) and 17% valgus (182). Ninety percent (968) had patella resurfacing performed, 62% (661) received cemented TKA fixation, on 32% hybrid fixation (cemented femoral component, cementless tibial tray) was performed and 6% (66) had cementless fixation. Two hundred thirty-seven cases were deceased before 20 years follow-up (22%). Results: At 10 to 21 years follow-up, 129 revisions were performed (12%). The most common reasons for revision were polyethylene wear, particle induced osteolysis, instability and pain (43% of revisions). Implant fixation significantly influenced the rate of revision with cemented fixation having a 6.7% rate of revision (44/661), hybrid fixation a 14% revision rate (47/336) and cementless a 36.4% revision rate (24/66). Excluding infections (11 cases), overall Kaplan-Meier survivorship at five, 10 and 15 years was 96.4%, 91.9% and 85.8%, respectively. At 20 years the predicted Kaplan-Meier survivorship was estimated at 83.5% (no revisions beyond 17.5 years). Cemented fixation was associated with significantly better survivorship than hybrid and cementless fixation (p< 0.0001). At 5, 10 and 15 years cemented AMK TKA survivorship was 97.5%, 94.9% and 91.9% respectively (no revision performed beyond 13.5 years). For hybrid fixation the survival at 5, 10 and 15 years was 97.8%, 92.2% and 85.1% respectively. Cementless AMK THA had a Kaplan-Meier survivor-ship of 88.9%, 78.2% and 57.4% at 5, 10 and 15 years respectively. Conclusion: Cemented fixation had superior outcomes compared to cementless and hybrid fixation with the most common reasons for revision being polyethylene wear and osteolysis. To our knowledge this the first medium to long term follow-up of the AMK TKA and it demonstrates that method of fixation had a major influence on revision rates and survivorship

Limb deformity is common in patients presenting for knee arthroplasty, either related to asymmetrical wear patterns from the underlying arthritic process (intra-articular malalignment) or less often major extra-articular deformity due to prior fracture malunion, childhood physical injury, old osteotomy, or developmental or metabolic disorders such as Blount's disease or hypophosphatemic rickets. Angular deformity that is above the epicondyles or below the fibular neck may not be easily correctable by adjusted bone cuts as the amount of bone resection may make soft tissue balancing impossible or may disrupt completely the collateral ligament attachments. Development of a treatment plan begins with careful assessment of the malalignment which may be mainly coronal, sagittal, rotational or some combination. Translation can also complicate the reconstruction as this has effects directly on location of the mechanical axis. Most intra-articular deformities are due to the arthritic process alone, but may occasionally be the result of intra-articular fracture, periarticular osteotomy or from prior revision surgery effects. While intra-articular deformity can almost always be managed with adjusted bone cuts it is important to have available revision type implants to enhance fixation (stems) or increase constraint when ligament balancing or ligament laxity is a problem. Extra-articular deformities may be correctable with adjusted bone cuts and altered implant positioning when the deformity is smaller, or located a longer distance from the joint. The effect of a deformity is proportional to its distance from the joint. The closer the deformity is to the joint, the greater the impact the same degree angular deformity will have. In general deformities in the plane of knee are better tolerated than sagittal plane (varus/valgus) deformity. Careful pre-operative planning is required for cases with significant extra-articular deformity with a focus on location and plane of the apex of the deformity, identification of the mechanical axis location relative to the deformed limb, distance of the deformity from the joint, and determination of the intra-articular effect on bone cuts and implant position absent osteotomy. In the course of pre-operative planning, osteotomy is suggested when there is inability to correct the mechanical axis to neutral without excessive bone cuts which compromise ligament or patellar tendon attachment sites, or alternatively when adequate adjustment of cuts will likely lead to excessive joint line obliquity which can compromise ability to balance the soft tissues. When chosen, adjunctive osteotomy can be done in one-stage at the time of TKA or the procedures can be done separately in two stages. When simultaneous with TKA, osteotomy fixation options include long stems added to the femoral (or tibial) component for intramedullary fixation, adjunctive plate and screw fixation, and antegrade (usually locked) nailing for some femoral osteotomies. Choice of fixation method is often influenced by specific deformity size location, bone quality and amount, and surgeon preference. Surgical navigation, or intra-operative x-ray imaging methods (or both) have both been used to facilitate accurate correction of deformity in these complex cases. When faced with major deformity of the femur or tibia, with careful planning combined osteotomy and TKA can result in excellent outcomes and durable implant fixation with less constraint, less bone loss, and better joint kinematics than is possible with modified TKA alone