Distal radius fractures have an incidence rate of 17.5% among all fractures. Their treatment in case of comminution, commonly managed by volar locking plates, is still challenging. Variable-angle screw technology could counteract these challenges. Additionally, combined volar and dorsal plate fixation is valuable for treatment of complex fractures at the distal radius. Currently, biomechanical investigation of the competency of supplemental dorsal plating is scant. The aim of this study was to investigate the biomechanical competency of double-plated distal radius fractures in comparison to volar locking plate fixation. Complex intra-articular distal radius fractures AO/OTA 23-C 2.1 and C 3.1 were created by means of osteotomies, simulating dorsal defect with comminution of the lunate facet in 30 artificial radii, assigned to 3 study groups with 10 specimens in each. The styloid process of each radius was separated from the shaft and the other articular fragments. In group 1, the lunate facet was divided to 3 equally-sized fragments. In contrast, the lunate in group 2 was split in a smaller dorsal and a larger volar fragment, whereas in group 3 was divided in 2 equal fragments. Following fracture reduction, each specimen was first instrumented with a volar locking plate and non-destructive quasi-static biomechanical testing under axial loading was performed in specimen's inclination of 40° flexion, 40° extension and 0° neutral position. Mediolateral radiographs were taken under 100 N loads in flexion and extension, as well as under 150 N loads in neutral position. Subsequently, all biomechanical tests were repeated after supplemental dorsal locking plate fixation of all specimens. Based on machine and radiographic data, stiffness and angular displacement between the shaft and lunate facet were determined. Stiffness in neutral position (N/mm) without/with dorsal plating was on average 164.3/166, 158.5/222.5 and 181.5/207.6 in groups 1–3. It increased significantly after supplementary dorsal plating in groups 2 and 3. Predominantly, from biomechanical perspective supplemental dorsal locked plating increases fixation stability of unstable distal radius fractures after volar locked plating. However, its effect depends on the fracture pattern at the distal radius

Distal femur fractures (DFF) are common, especially in the elderly and high energy trauma patients. Lateral locked osteosynthesis constructs have been widely used, however non-union and implant failures are not uncommon. Recent literature advocates for the liberal use of supplemental medial plating to augment lateral locked constructs. However, there is a lack of proprietary medial plate options, with some authors supporting the use of repurposing expensive anatomic pre-contoured plates. The aim of this study was to investigate the feasibility of a readily available cost-effective medial implant option. A retrospective analysis from January 2014 to June 2022 was performed on DFF (primary or revision) managed with supplemental medial plating with a Large Fragment Locking Compression Plate (LCP) T-Plate (~$240 AUD) via a medial sub-vastus approach. The T-plate was contoured and placed superior to the medial condyle. A combination of 4.5mm cortical, 5mm locking and/or 6.5mm cancellous screws were used, with oblique screw trajectories towards the distal lateral cortex of the lateral condyle. All extra-articular fractures and revision fixation cases were allowed to weight bear immediately. The primary outcome was union rate. This technique was utilised on sixteen patients; 3 acute, 13 revisions; mean age 52 years (range 16-85), 81% male, 5 open fractures. The union rate was 100%, with a median time to union of 29 weeks (IQR 18-46). The mean follow-up was 15 months. There were two complications: a deep infection requiring two debridements and a prominent screw requiring removal. The mean range of motion was 1–108. o. . Supplemental medial plating of DFF with a Large Fragment LCP T-Plate is a feasible, safe, and economical option for both acute fixation and revisions. Further validation on a larger scale is warranted, along with considerations to developing a specific implant in line with these principles

Dual plating of the medial and lateral distal femur has been proposed to reduce angular malunion and hardware failure secondary to delayed union or nonunion. This strategy improves the strength and alignment of the construct, but it may compromise the vascularity of the distal femur paradoxically impairing healing. This study investigates the effect of dual plating versus single plating on the perfusion of the distal femur. Ten matched pairs of fresh-frozen cadaveric lower extremities were assigned to either isolated lateral plating or dual plating of a single limb. The contralateral lower extremity was used as a matched control. A distal femoral locking plate was applied to the lateral side of ten legs using a standard sub-vastus approach. Five femurs had an additional 3.5mm reconstruction plate applied to the medial aspect of the distal femur using a medial sub-vastus approach. The superficial femoral artery and the profunda femoris were cannulated at the level of the femoral head. Gadolinium MRI contrast solution (3:1 gadolinium to saline ration) was injected through the arterial cannula. High resolution fat-suppressed 3D gradient echo sequences were completed both with and without gadolinium contrast. Intra-osseous contributions were quantified within a standardized region of interest (ROI) using customized IDL 6.4 software (Exelis, Boulder, CO). Perfusion of the distal femur was assessed in six different zones. The signal intensity on MRI was then quantified in the distal femur and comparison was made between the experimental plated limb and the contralateral, control limb. Following completion of the MRI protocol, the specimens were injected with latex medium and the extra-osseous vasculature was dissected. Quantitative MRI revealed that application of the lateral distal femoral locking plate reduced the perfusion of the distal femur by 21.7%. Within the dual plating group there was a reduction in perfusion by 24%. There was no significant difference in the perfusion between the isolated lateral plate and the dual plating groups. There were no regional differences in perfusion between the epiphyseal, metaphyseal or meta-diaphyseal regions. Specimen dissection in both plating groups revealed complete destruction of any periosteal vessels that ran underneath either the medial or lateral plates. Multiple small vessels enter the posterior condyles off both superior medial and lateral geniculate arteries and were preserved in all specimens. Furthermore, there was retrograde flow to the distal most aspect of the condyles medially and laterally via the inferior geniculate arteries. The medial vascular pedicle was proximal to the medial plate in all the dual plated specimens and was not disrupted by the medial sub-vastus approach in any specimens. Fixation of the distal femur via a lateral sub-vastus approach and application of a lateral locking plate results in a 21% reduction in perfusion to the distal femur. The addition of a medial 3.5mm reconstruction plate does not significantly compromise the vascularity of the distal femur. The majority of the vascular insult secondary to open reduction, internal fixation of the distal femur occurs with application of the lateral locking plate

Introduction. Distal femur fracture fixation in elderly presents significant challenges due to osteoporosis and associated comorbidities. There has been an evolution in the management of these fractures with a description of various surgical techniques and fixation methods; however, currently, there is no consensus on the standard of care. Non-union rates of up to 19% and mortality rates of up to 26 % at one year have been reported in the literature. Delay in surgery and delay in mobilisation post-operatively have been identified as two main factors for high rate of mortality. As biomechanical studies have proved better stability with dual plating or nail-plate combination, a trend has been shifting for past few years towards rigid fixation to allow early mobilisation. Our study aims to compare outcomes of distal femur fractures managed with either single plate (SP), dual plating (DP) or nail-plate construct (NP). Methods. A retrospective review of patients aged above 65 years with distal femur fractures (both native and peri-prosthetic) who underwent surgical management between June 2020 and May 2023 was conducted. Patients were divided into three groups based on mode of fixation - single plate or dual plating or nail-plate construct. AO/OTA classification was used for non-periprosthetic, and Unified classification system (UCS) was used for periprosthetic fractures. Data on patient demographics, fracture characteristics, surgical details, postoperative complications, re-operation rate, radiological outcomes and mortality rate were evaluated. Primary objective was to compare re-operation rate and mortality rate between 3 groups at 30 days, 6 months and at 1 year. Results. A cohort of 32 patients with distal femur fractures were included in this study. 91% were females and mean age was 80.97 (range 68–97). 18 (53%) were non-periprosthetic fracture and 14 (47%) were periprosthetic fractures.18 patients underwent single plate fixation (AO/OTA 33A – 8, 33B/C – 2, UCS V3B – 5, V3C – 3),10 patients had dual plate fixation (AO/OTA 33A – 1, 33B/C – 4, UCS V3B – 3, V3C – 2) and 4 patients underwent nail-plate combination fixation (AO/OTA 33A – 4). 70.5% patients had surgery within 36 hours of admission and 90% within 48 hours. Analysis showed no re-operation at 30 days, 6 months in all 3 groups. At 1 year one patient had re-operation in dual-plating periprosthetic group (Distal femur replacement done for failed fixation). Three patients (16%) in single plate group had re-operation at 2 years (2 for peri-implant fracture and 1 for infection). None of the patients treated with Nail-plate combination had re-operation. Mortality rate at 30 days was 0% in among all the 3 groups. At 6 months, it was 16% in single plate group and 0% in DP and NP groups at 6 months and at 1 year mortality rate was 27% in SP group, 10% in DP and 0% in NP group. Combined mortality rate was 0% at 30 days, 9% at 6 months and 18.7% at one year. Conclusion. Our analysis provides insights into fixation methods of distal femur fractures in elderly patients. We conclude that a lower re-operation rate and mortality rate can be achieved with early surgery and rigid fixation with either dual plating or nail-plate construct to allow early mobilisation. Further prospective studies are warranted to confirm these findings and guide the selection of optimal surgical strategies for these challenging fractures

Neer Type-IIB lateral clavicle fractures are inherently unstable fractures with associated disruption of the coracoclavicular (CC) ligaments. A novel plating technique using a superior lateral locking plate with antero-posterior (AP) locking screws, resulting in orthogonal fixation in the lateral fragment has been designed to enhance stability. The purpose of this study was to biomechanically compare three different clavicle plating constructs. 24 fresh-frozen cadaveric shoulders were randomised into three groups (n=8 specimens). Group 1: lateral locking plate only (Medartis Aptus Superior Lateral Plate); Group 2: lateral locking plate with CC stabilisation (Nr. 2 FiberWire); and Group 3: lateral locking plate with two AP locking screws stabilising the lateral fragment. Data was analysed for gap formation after cyclic loading, construct stiffness and ultimate load to failure, defined by a marked decrease in the load displacement curve. After 500 cycles, there was no statistically significant difference between the three groups in gap-formation (p = 0.179). Ultimate load to failure was significantly higher in Group 3 compared to Group 1 (286N vs. 167N; p = 0.022), but not to Group 2 (286N vs. 246N; p = 0.604). There were no statistically significant differences in stiffness (Group 1: 504N/mm; Group 2: 564N/mm; Group 3: 512N/mm; p = 0.712). Peri-implant fracture was the primary mode of failure for all three groups, with Group 3 demonstrating the lowest rate of peri-implant fractures (Group 1: 6/8; Group 2: 7/8, Group 3: 4/8; p = 0.243). The lateral locking plate with orthogonal AP locking screw fixation in the lateral fragment demonstrated the greatest ultimate failure load, followed by the lateral locking plate with CC stabilization. The use of orthogonal screw fixation in the distal fragment may negate against the need for CC stabilization in these types of fractures, thus minimizing surgical dissection around the coracoid and potential complications

Introduction. To determine the advantages and risks of plating after lengthening (PAL) of tibia in children and adolescents. Materials and Methods. 35 consecutive tibial lengthenings were done for limb length discrepancy (LLD) in 26 patients. Gradual lengthening by an external fixator from a tibial (usually diaphyseal) osteotomy was followed by internal fixation with a lateral tibial submuscular plate. The mean age at the time of the lengthening was 10.3 years (4.8 – 16.8 years). The aetiology for LLD was congenital in 21, acquired in 3, and developmental in 2 patients. The mean follow-up was 4.3 years (8 months – 9.9 years). Results. The mean lengthening was 5cm (3–8.6cm) or 19.1% (10.8 – 35.2%) of the initial length of tibia. It took 78.8 days to reach the target length at a lengthening rate of 0.75mm/day. The mean time to plate substitution after cessation of lengthening was 24.7days/109 days after osteotomy. This led to an average external fixation index (EFI) of 23.1days/cm. Optimisation of this technique by judicious estimation of timing of plate substitution would reduce the EFI. Consolidation was recorded at 192 days after osteotomy. Bone healing index (BHI) was 39.8days/cm and was age dependent: <12 year olds = 37.5 days/cm; 12 years = 44.7 days/cm. Using the estimated consolidation time if treatment was solely by external fixator, calculated by tripling the time taken to reach target length after osteotomy, the BHI in this series would have been 52.9 days/cm (p < 0.001). Knee flexion recovery to > 90 degrees was noted at 153.5 days after plating. One greenstick fracture occurred 116 days after plate insertion, 1 tibial shaft fracture occurred 315 days post removal of plate - both following injury and were treated conservatively. Six episodes of sepsis, 5 superficial and 1 deep were treated with antibiotic suppression. The plates were removed from 28 tibiae, 437.4 days after insertion. Conclusions. Plating after lengthening not only reduces the fixator time but appears to achieve consolidation faster than if treatment was by external fixation alone. This facilitates early recovery of joint motion and limb function

This study reports the results of open reduction and internal fixation of 26 unstable, intra-articular, dorsally displaced fractures of the distal radius using a bio absorbable dorsal distal radius (Reunite) plate and calcium phosphate (Biobon) bone substitute. The bio absorbable plate has the advantages of being low profile, easily contourable due to temporary malleability and is angularly stable. It retains its strength for 6 to 8 weeks and undergoes complete mass loss within one year, thereby allowing gradual load transfer to the healing bone. In the majority of cases, this plate produces functional results comparable with metal plates. The Gartland and Werley score was excellent or good in 21 patients. The most important advantage over metal plates is in eliminating the need to remove the plate and hence the need for a second operation if implant related extensor tenosynovitis occurs. Inflammatory tissue reaction to the degradation products of the plate is a potential concern, although the co-polymer ratio used in this plate appears to have reduced the severity of this reaction, which was seen in two patients in this series. The reduction was lost in five patients with severe dorsal comminution. For such fractures, the plate did not retain its strength for long enough to allow adequate healing for satisfactory load transfer. Following this experience, we do not recommend this plating system for fractures with a metaphyseal gap of greater than 7 mm following reduction. For fractures that cannot be treated by closed means but where the metaphyseal gap following reduction is less than 7 mm, this plate provides all the theoretical advantages. Further developments allowing the plate to retain its strength for longer while maintaining the low incidence of inflammatory reactions will make it more universally applicable for the treatment of a greater spectrum of unstable distal radius fractures

Introduction. Management of Vancouver type B1 and C periprosthetic fractures in elderly patients requires fixation and an aim for early mobilisation but many techniques restrict weightbearing due to re-fracture risk. We present the clinical and radiographic outcomes of our technique of total femoral plating (TFP) to allow early weightbearing whilst reducing risk of re-fracture. Methods. A single-centre retrospective cohort study was performed including twenty-two patients treated with TFP for fracture around either hip or knee replacements between May 2014 and December 2017. Follow-up data was compared at 6, 12 and 24 months. Primary outcomes were functional scores (Oxford Hip or Knee score (OHS/OKS)), Quality of Life (EQ-5D) and satisfaction at final follow-up (Visual Analogue Score (VAS)). Secondary outcomes were radiographic fracture union and complications. Results. Mean OHS and OKS was 50.25, EQ-5D score was >4 for all modalities, VAS was 64.4/100. Radiographs demonstrated bony union in 58% at 3 months and 76% at 6 months. We identified no case of re-fracture however non-union occurred in 4 patients. No other operative complications were identified. Conclusion. These results suggest that TFP may be a safe, viable option for management of periprosthetic fractures around stable implants allowing the benefit of early weightbearing, satisfactory outcomes and low re-fracture risk

Periprosthetic femoral shaft fractures are a significant complication of total hip arthroplasty. Plate osteosynthesis with or without onlay strut allograft has been the mainstay of treatment around well-fixed stems. Nonunions are a rare, challenging complication of this fixation method. The number of published treatment strategies for periprosthetic femoral nonunions are limited. In this series, we report the outcomes of a novel orthogonal plating surgical technique for addressing nonunions in the setting of Vancouver B1 and C-type periprosthetic fractures that previously failed open reduction internal fixation (ORIF). A retrospective chart review of all patients from 2010 to 2014 with Vancouver B1/C total hip arthroplasty periprosthetic femoral nonunions was performed. All patients were treated primarily with ORIF. Nonunion was defined as no radiographic signs of fracture healing nine months post-operatively, with or without hardware failure. Exclusion criteria included open fractures and periprosthetic infections. The technique utilised a mechanobiologic strategy of atraumatic exposure, resection of necrotic tissue, bone grafting with adjuvant recombinant growth factor and revision open reduction internal fixation. Initially, compression was achieved using an articulated tensioning device and application of an anterior plate. This was followed by locked lateral plating. Patients remained non-weight bearing for eight weeks. Six Vancouver B1/C periprosthetic femoral nonunions were treated. Five patients were female with an average age of 80.3 years (range 72–91). The fractures occurred at a mean of 5.8 years (range 1–10) from their initial arthroplasty procedure. No patients underwent further revision surgery; there were no wound dehiscence, hardware failures, infections, or surgical complications. All patients had a minimum of nine months follow up (mean 16.6, range 9–36). All fractures achieved osseous union, defined as solid bridging callus over at least two cortices and pain free, independent ambulation, at an average of 24.4 weeks (range 6.1–39.7 weeks). To our knowledge, this is the first case series describing 90–90 locked compression plating using modern implants for periprosthetic femoral nonunions. This is a rare but challenging complication of total hip arthroplasty and we present a novel solution with satisfactory preliminary outcomes. Orthogonal locked compression plating utilising an articulated tensioning device and autograft with adjuvant osteoinductive allograft should be considered in periprosthetic femur fractures around a well-fixed stem. Further biomechanical and clinical research is needed to improve our treatment strategies in this population

Pilon fractures are associated to significant soft tissue injury, as well as soft tissue complications. The soft tissue on the medial side of the distal tibia is often involved, likely due to a lack of muscle investment. Medial approaches and medial plate application may well add to the soft tissue trauma. The objective of this study was to examine the relationship between medial plating and soft tissue complications in our center. This is a retrospective study based on a prospective database. Pilon cases treated with plate and screw fixation were identified between 2011 and 2014. Injury characteristics, patient demographics, and soft tissue complications were collected from chart review. Soft tissue complications recorded included any wound or skin problem, as well as patient complaints of hardware irritation leading to hardware removal. Logistic regression was employed. Independent variables for the model included medial plating, the presence of open fracture, smoking status and diagnosis of diabetes. Two models were created, one with the dependent variable as presence of any soft tissue complication, and the second model with the dependent variable as presence of a wound complication, which required surgical intervention. The study included 91 patients, 89 of whom had full data with an average follow up of 11.6 months (1–33 months). The incidence of soft tissue complications, including hardware irritation, was 26% (n=23), and 13% (n=12) required surgical treatment. Smoking status was the only predictor of soft tissue complications with an odds ratio of 3.6 (95%CI 1.2, 10.4; p=0.02), while controlling for other independent variables. The model explained 12% of the variation in soft tissue complications (Cox and Snell 0.119, p=0.028). In the second model, presence of a medial plate predicted soft tissue complications requiring surgical intervention with an odds ratio of 8.8 (95%CI 1.1, 73.7; p=0.045), while controlling for the other independent variables. The model explained 10% of the variation in soft tissue complications requiring surgical intervention (Cox and Snell 0.095, p=0.035). The use of a medial plate does not appear to correlate to general soft tissue complications in pilon fractures. Smoking status increased the odds of a soft tissue complication more than three fold. The use of medial plating did increase the odds of soft tissue complications that required surgical treatment almost nine fold. It appears medial plating is not related to soft tissue complications, however treating soft tissue compilations in the presence of a medial plate may require more invasive methods

The radius has a sagittal and coronal bow. Fractures are often treated with volar anterior plating. However, the sagittal bow is often overlooked when plating. This study looks at radial morphology and the effect of plating the proximal radius, with straight plates then contoured plates bowed in the sagittal plane. We report our findings and their effect on forearm rotation. Morphology was investigated using fourteen radii. Attention was made to the proximal shaft of the radius and its sagittal bow, from this 6, 7 and 8 hole plates were contoured to fit this bow. A simple transverse fracture was then made at the apex of this bow. Supination and pronation was then compared when plating with a straight plate and a contoured plate. Ten cadavers had the ulna plating at the same level. The effect on rotation of fractures plated in the distal third shaft was also measured. A significant reduction in rotation was found, when a proximal radius fracture was plated with straight plate compared to a contoured plate: 10.8, 12.8, 21.7 degrees (p<0.05 for 6, 7, 8 hole plates). Forearm rotation was decreased further when a longer plate was used. Ulna or distal shaft plating did not reduce rotation. This study has shown a significant sagittal bow of the proximal shaft of the radius. Plating this with contoured plates in the sagittal plane improves rotation when compared to straight plates. Additional ulna plating is not a source of reduced forearm rotation

Introduction. Recently ventral plating implants made of carbon/PEEK composite material have been developed with apparently superior material properties in terms of implant fatigue and imaging suitability. In this study we assessed the outcome of the first clinical application of this new implant. Methods. Retrospective, single-center case series of 16 consecutive patients between 2011 and 2013 undergoing ventral stabilization surgery with a new carbon plating system (see figure 1). We collected data in terms of safety of the procedure (screw positioning, blood loss, operation time), quality and reliability of the implant (revisions, dislocations, screw loosening, fusion, adjacent segment degeneration), clinical outcome and biological tolerance (cervical pain / discomfort, dysphagia). Results. All patients were available for clinical and radiological follow up. Mean surgery time was 128 minutes, in 11 cases one in 5 cases 2 segments were treated. The clinical findings and patient's satisfaction were good in 14 and fair in two cases. All patients who completed the 6 months control had a radiographically confirmed interbody fusion; no implant loosening or failure and no infections were observed. (see figure 2). There was one implant related complication (dysphagia due to malpositioning of the plate which was removed 4 days after implant insertion) and one complication related to the approach (Horner's syndrome). Conclusion. In this retrospective study of 16 patients we found that the use of a carbon-composite plating system lead to results comparable to the “gold standard” metal plates in terms of safety / clinical outcome and reliability of the implant. There was one revision due to dysphagia. The MR imaging of the patients who have been operated with the carbon/PEEK system showed superior quality with reduced artifacts and improved diagnostical properties, especially when evaluating the neurogical structures. (see figure 3). The overall clinical outcome and patient acceptance of the implant was good. The radiologic findings on follow up of 2, 6 and 12 months have shown a high fatigue strength with no signs of implant failure in terms of dislocation, loosening or breakage. Therefore we conclude that the use of the carbon/PEEK plating system is suitable for ventral stabilization in trauma and degenerative disease

Introduction:. Displaced and shortened clavicle shaft fractures can be treated operatively by intra- or extramedullary fixation. The aim of the study was to compare the effectiveness of these two treatment modalities. Methods:. Forty seven patients with acute displaced and shortened clavicle shaft fractures were randomly assigned to either an intramedullary locked fixation group or an anatomically contoured locked plating group. All patients were operated by the same surgeon and had identical post-operative treatment regimes. The effectiveness of both treatment regimens were assessed based on; incision length, operative time and union rate. Disabilities of the Arm, Shoulder and Hand Score (DASH) and Constant Shoulder Score were assessed one year post-operatively. Results:. Twenty-five patients were included in the plating group and twenty-two in the intramedullary fixation group. No differences between the two groups were found for age, gender, fracture comminution and/or displacement. Incision size was significantly (p<0.0001) smaller in the nailing group (38±9 mm) than in the plating group (118±19 mm). In line with this the operating time was also shorter in the nailing group than in the plating groups (43±8 min and 60±19 min, respectively (p=0.0029)). One year postoperatively a 100% union rate was achieved in both groups. Lower DASH scores (2±5 vs 16±18 (p=0.0071)) and higher Constant Shoulder scores (96±6 vs. 90 ± 18 (p=0.0122)), were found in the nailing group. Conclusion:. Both anatomically contoured locked plating and locked intramedullary fixation resulted in successful treatment of displaced and shortened clavicle shaft fractures. Intramedullary fixation however was associated with shorter operating times and smaller incision sizes. In addition, better DASH and Constant Shoulder scores were found in the nailing group one year post operatively. Based on these finding and the absence of prominent subcutaneous hardware necessitating removal of the nail, the intramedullary device is a good alternative to treat displaced clavicle shaft fractures

The radiological evidence of implant failure following plate fixation of traumatic pubic symphysis diastasis can be up to 75%. We report the complications following symphyseal double orthogonal plating in patients with pubic symphysis diastasis over a period of 2.5 years. Patient records and radiographs of 38 consecutive patients were reviewed with mean follow up of 12.5 months. 5 patients (13%) had radiological evidence of implant failure with one patient (2.6%) requiring revision surgery. There was no evidence of wound complications. We conclude that our lower rate of revision surgery and metal work failure is attributed to double orthogonal plating

The outcome of 77 high energy tibial plateau fractures treated by locking or conventional plating was reviewed. The aim of the study was to determine if there was any advantage of locking plates in reducing the complication rates associated with fixation of these injuries. All patients had a high energy injury pattern (medial or bicondylar plateau fractures). There were 32 locked plates and 45 non-locking plates used. Compartment syndrome complicated 5 patients (16%) in the locked plate group and 3 (7%) in the non-locked group (p = 0.198). Superficial infection occurred in 4 (13%) patients with locked plates and 7 (16%) patients with non-locked plates. Thromboembolic complications occurred in 3 (7%) patients treated with non-locked plates. There were no thrombembolic complications in the locked plate group (p = 0.135). Overall, malunion of the plateau occurred in 10 (22%) patients treated with non-locked plates compared to 7 (22%) patients who received locked plates. This was due to residual malreduction in 4 (13%) patients in the locked plate group and 6 (13%) patients in the non-locked plate group at the time of surgery. In the remaining cases loss of reduction after fixation occurred in 4 (9%) patients who received non-locked plates and in 3 (9%) patients who were treated with locked plates. No statistically significant difference was noted in the treatment outcomes of patients managed with locked plates or non-locked plates, regardless of fracture severity. We concluded that there is no definite advantage associated with the use of locked plating for high energy tibial plateau fractures

Cobalt-chrome alloys are widely used in dentistry and Orthopaedic implant industry. Vitallium is a similar alloy which contains 60% cobalt, 20% chromium, 5% molybdenum along with traces of other substances. It has been in use along with stainless steel for the last century because of its lightweight, favourable mechanical properties and resistance to corrosion. We present an unusual case of synovial cyst formation following Vitallium plating mimicking a sarcoma. To our knowledge, we are the first to report a delayed tissue reaction to Vitallium plating 40 years after its implantation. A 78 yrs old man had a right femoral intertrochanteric fracture 40 years ago, which was fixed with a Vitallium nail plate. His postoperative recovery was uneventful and he regained full function of his leg. 3 years prior to excision, he presented with a painless swelling around his right upper thigh to our unit. Aspiration of the swelling and investigations were requested but patient was lost to follow up due to social reasons. Seven months prior to excision, he represented as the swelling had increased to the extent that it was involving the anterior and posterior aspect of the upper thigh with pressure necrosis of skin posteriorly. Examination revealed painless, transilluminable, fluctuant multilobular swelling over the right proximal femur overlying the healed surgical scar. Compression of the larger lobe in the buttock clearly forced fluid into the anterior compartment of the thigh where again swelling was extensive. Surprisingly he had full range of movements at the hip joint. Radiograph of the hip showed a soft tissue swelling with a healed fracture and Vitallium implant insitu. Cytology was negative. MRI scan showed multiloculated cystic lesions extending anteriorly, laterally and posteriorly into the intermuscular and subcutaneous planes around the right proximal femur. Multiple small dependent foci likely representing debris or synovial proliferation was seen within loculations. Excision of the cystic lesions with removal of metal work was performed. The old incision was reopened in the lateral position and a large cystic lesion with a thick capsule was dissected down to the metal work. The lesion was lying superficial to the vastus lateralis but was communicating with metal work. The metal work was removed with difficulty, no visible metallosis. A second cystic lesion was located more posteriorly but its neck was communicating with the thin hole into the first lesion. The lesion was excised completely. Macroscopic examination showed two cysts 9×8×5.5cm and 20×10×7.5cm with a smooth external surface and the lumen appeared trabecular containing numerous loose (rice) bodies. Microscopy showed a dense fibrotic cyst wall with lumen with multiple small nodules containing organised fibrinous and eosinophilic material. Several foci of cellular debris including lymphocytes and macrophages were scattered in nodules best representing a synovial cyst with loose/rice bodies. No malignancy was seen. We recommend early removal of metal work if it shows any signs of local reaction provided fracture is united. Be aware of large foreign body/ hypersensitivity reaction and incompatible equipment for removal

Purpose:. To review the union rates, outcomes and complications of angular stable plating of lateral third clavicle fractures. Method:. Between 2007 and 2010 angular stable plates were used in the fixation for seventeen patients with displaced lateral third clavicle fractures (Allman Group II, Type 2). These were identified from surgical log books and operation codes. The surgical and clinical notes as well as X-rays were reviewed. The patients were contacted telephonically. An Oxford Shoulder Score and questions relating to plate removal, scar pain and return to activities were asked. Three patients were not contactable. Results:. There were 16 males. The average age was 44. The average time to union was 3 months (range 2 to 4). There were no complications. The average Oxford Shoulder Score was 13 (range 12–19). No plates have required removal but 2 patients have requested removal for discomfort. All but 3 patients have returned to full activity. Conclusion:. The use of angular stable plates for fixation of type 2 lateral end of clavicle fractures results in excellent union rates by 3 months with only 3 patients requesting elective plate removal. This is in contrast to hook plates which require mandatory removal. No other complication was encountered

Aim. To evaluate the outcome and complications of pubic symphysis plating in the stabilisation of traumatic anterior pelvic ring injuries. Methods. All patients who underwent anterior pelvic ring stabilisation with a pubic symphysis plate in a tertiary referral pelvic and acetabular reconstruction unit were studied. Patients were followed up annually for five years with AP, inlet and outlet radiographs at each visit. The fracture classification, type of fixation (including additional posterior fixation), and incidence of metalwork failure were recorded. Results. In a series of 178 consecutive patients, 159 (89%) were studied for a mean of 41 months (range 3 months to 13 years). There were 121 males and 38 females, with a mean age of 38 years (9-80yrs). Symphysis pubic fixation was performed in 105 AO-OTA type B and 54 AO-OTA type C injuries using a Matta symphyseal plate in 92, a reconstruction plate in 65, or a DCP in two patients. Supplementary posterior pelvic fixation was performed in 103 patients. Six patients (3.8%) required revision for failure of fixation or symptomatic instability of the pubic symphysis. A further seven patients (4%) had metalwork removed for other reasons. Metalwork breakage occurred in 66 patients (42%). 64 of these 66 patients were asymptomatic and metalwork was left in situ. Conclusion. Plate fixation of the symphysis pubis is an effective method of stabilising anterior pelvic ring injuries with a low rate of complications. There is a high rate of late metalwork breakage, but this is often not clinically significant

Increased use of locking volar plates for distal radius fractures led to a number of reports in literature of flexor tendon injuries from impingement and attrition against hardware. Repair of the pronator quadratus is critical in preventing tendon injury. We present a pronator quadratus sparing approach to the distal radius. The senior author has used a pronator quadratus sparing lateral pillar approach for for the past five years. A lateral incision is used over the radial styloid. The first dorsal compartment is released and APL and EPB tendons retracted. The underlying brachio-radialis tendon and insertion fascia is split and the palmar portion elevated off the distal radius with the pronator quadratus as a single contiguous sheet. The distal edge of the pronator quadratus is elevated from the wrist capsule by sharp dissection. The radial artery is protected by the retracted tissue. Repair of the brachio-radialis tendon and insertion fascia is much more robust than that of the pronator quadratus covering the entire plate. Since 2004, the senior author has used the pronator quadratus sparing approach for volar plating of the distal radius, in 183 cases. At last follow-up there were no instances of flexor tendon injury, which was considered to be one of the outcome measures and end-points. There was no impingement in the first dorsal compartment, except in two cases of lateral pillar hardware impingement from additional lateral pillar plate fixation through the same approach. Nine cases had minor persistent superficial radial nerve parasthesia. One case had a superficial wound infection requiring drainage. The repaired pronator quadratus formed a barrier protecting the plate. The infection was aggressively treated and the plate left in situ for three months till fracture union. Cultures from the retrieved plate showed no organisms. Another implant had two of the locking screws back out. The pronator quadratus fascia was tented with an underlying haematoma. The fascia however only showed minimum screw penetration and no flexor tendon injury. Average wrist dorsiflexion was 72 deg and palmar flexion 65 deg. Average pronation was 81 deg and average supination 69 deg. Supination range was slow to recover in younger patients. One explanation could be the tight pronator quadratus repair. Average PRWE and DASH scores were 19. The quadratus sparing approach to the volar distal radius is easy to perform and protects the flexor tendons at the wrist. Cases demonstrated that an intact pronator quadratus can act as an effective barrier to prominent hardware and superficial infection. Supination range may be reduced by this approach due to a tight repair, though a palmar DRUJ capsule contracture may also be an explanation

Aims. To study the outcomes of DVR plating for distal radius fractures. Methods. We prospectively studied all patients managed with a DVR plate, over a twelve-month period in 2006/07. All patients were seen in our dedicated research clinic at 2, 6, 12 and 26 weeks post-operatively. Physiotherapy started at 2 weeks post-operatively. Active range of motion (ROM) of the injured wrist was recorded at 6, 12 and 26 weeks and compared with the normal side. Standardised radiographs were taken at 2 and 6 weeks and compared with pre- and post-operative films for radial and volar angulations, relative radial length, ulnar variance and implant position. Patient satisfaction was measured with the Patient Rated Wrist Evaluation score (PRWE) at 6, 12 and 26 weeks. Results. 129 patients (male:female 1:3) with a median age of 59 years (92-17 years) were seen. Mean measurements of pre-operative films were of 16 degrees dorsal angulation, 15 degrees radial inclination, 7 mm relative radial length and +2mm ulnar variance. In comparison post-operative results were -6 degrees, +22 degrees, 11mm and 0mm respectively, which remained unchanged at 2 and 6 weeks. The mean comparative active ROM was 70%, 88% and 98% at 6, 12 and 26 weeks respectively. The PRWE Score showed a mild degree of disability at 6 weeks and only minimal disability at 12 and 26 weeks. There were two cases of lost fracture position and no case of deep infection. Conclusion. Our study suggests that the DVR locking plate provides excellent fracture stability, allowing for early rehabilitation, with minimal complications. Radiological measurements were markedly improved and this correlated with a good ROM and high patient satisfaction. We recommend the use of the DVR plate to manage unstable distal radius fractures