Second-generation metal-on-metal bearings have been used since the late 1980s as alternative bearings to eliminate aseptic loosening due to polyethylene wear. This study is the first with a long term follow-up for Meteasul, (Zimmer GmbH, Winterthur, Switzerland) metal on metal (MoM) hip replacement; in literature most of the studies have a mean follow-up of 7 years. Metasul showed better performances than other MoM couplings, with a low failure rate at long term follow-up and low revision rate for aspetic loosening. The aim of the present study was to evaluate the long-term results of a series of Metasul implanted between January 1993 and July 1997. 145 cementless THAs with a 28 mm Metasul articulation were performed in 114 consecutive patients. Implant survivorship was calculated and clinical and radiographic evaluations were performed on 93 hips still available for follow-up at a mean of 19 years postoperatively (43 hips are dead or lost to FU, 29, 6%). Nine hips (6.2%) were revised. The cumulative probability of survival of the overall implant at 19 years postoperatively with revision for any reason as the end point, was 0.937 (95% confidence interval, 0.888 to 0.985). The cumulative probability of survival of Metasul with revision for any reason as the end point, was 0.956 (95% confidence interval, 0.916 to 0.997). Clinical outcome has been evaluated with modified Harris Hip Score for 93 hips with an average of 88.8 points. Various degrees of radiolucencies and osteolysis were found proximally around the femoral components of 25 hips (20%). Most of the patients has normal serum levels of metal ions (Co and Cr), and no cases of systemic toxicity has been reported. Cementless Metasul THAs showed high probability of survival at 19 years postoperatively

Ceramic-on-ceramic bearings provide a solution to the osteolysis seen with traditional metal-on-polyethylene bearings. Sporadic reports of ceramic breakage and squeaking concern some surgeons and this bearing combination can show in vivo signs of edge loading wear which was not predicted from in vitro studies. Taper damage or debris in the taper between the ceramic and metal may lead to breakage of either a ceramic head or insert. Fastidious surgical technique may help to minimise the risk of ceramic breakage. Squeaking is usually a benign complication, most frequently occurring when the hip is fully flexed. Rarely, it can occur with each step of walking when it can be sufficiently troublesome to require revision surgery. The etiology of squeaking is multifactorial in origin. Taller, heavier and younger patients with higher activity levels are more prone to hips that squeak. Cup version and inclination are also relevant factors. Osteolysis following metal-on-UHMW polyethylene Total Hip Arthroplasty (THA) is well reported. Earlier generation ceramic-on-ceramic bearings did produce some osteolysis, but in flawed implants. As third and now fourth generation ceramic THAs come into mid- and long-term service, the orthopaedic community has begun to see reports of high survival rates and very low incidence of osteolysis in these bearings. The technique used by radiologists for identifying the nature of lesions on Computed Tomography (CT) scan is the Hounsfield score which will identify the density of the tissue within the lucent area. Commonly the radiologist will have no access to previous imaging, especially pre-operative imaging if a long time has elapsed. With such a low incidence of osteolysis in this patient group, what, then, should a surgeon do on receiving a CT report on a ceramic-on-ceramic THA, which states there is osteolysis? This retrospective review aims to determine the accuracy of CT in identifying true osteolysis in a cohort of long-term third generation ceramic-on-ceramic uncemented hip arthroplasties in our department. Pelvic CT scans were performed on the first 27 patients from a cohort of 301 patients undergoing 15-year review with third generation alumina-alumina cementless THAs. The average follow-up was 15 years (15–17). The CT scans were reviewed against pre-operative and post-operative radiographs and reviewed by a second musculoskeletal specialist radiologist. Eleven of the CT scans were reported to show acetabular osteolysis, two reported osteolysis or a possible pre-existing cyst and one reported a definitive pre-existing cyst. After review of previous imaging including pre-operative radiographs, eleven of the thirteen patients initially reported to have osteolysis were found to have pre-existing cysts or geodes in the same size and position as the reported osteolysis, and a further patient had spot-welds with stress-shielding. One patient with evidence of true osteolysis awaits aspiration or biopsy to determine if he has evidence of ceramic wear or metallosis. Reports of osteolysis on CT should be interpreted with care in modern ceramic-on-ceramic THA to prevent unnecessary revision. Further imaging and investigations may be necessary to exclude other conditions such as geodes, or stress shielding which are frequently confused with osteolysis on CT scans

Intra-operative fractures of the femur are on the rise mainly due to the increased use of cementless implants and the desire to get a tight press fit. The prevalence has been reported to be between 1–5% in cementless THAs. The key to preventing these fractures is to identify patients at high risk and careful surgical technique. Surgical risk factors include the use of cementless devices, revision hip surgery, the use of flat tapered wedges and MIS surgery. Patient factors that increased risk include increasing age, female gender, osteopenia and rheumatoid arthritis. These risk factors tend to be additive and certainly when more than one is present extra caution needs to be taken. Surgical technique is critical to avoid these intra-operative fractures. Fractures can occur during exposure and dislocation, during implant removal (in revision THA), during canal preparation and most commonly during stem insertion. In both primary, and especially in revision, THA be wary of the stiff hip in association with osteopenia or osteolysis. These patients require a very gentle dislocation. If this cannot be achieved, then alteration of the standard approach and dislocation may be needed. Examples of these include protrusion with an osteopenic femur and revision THA with a very stiff hip with lysis in the femur. Lastly, in cases with retained hardware, dislocate prior to removing plates and screws. After dislocation, the next challenge is gentle preparation of the femoral canal. A reasonable exposure is required to access the femoral canal safely. MIS procedures do not offer good access to femoral canal and this probably results in increased risk of fracture during broaching or implant insertion. When broaching, stop when broach will not advance further. When inserting a tapered wedge stem, be worried if stem goes further in than broach. In revision surgery, when taking the stem out from above, make sure the area of the greater trochanter does not overhang the canal. A high speed burr can clear the shoulder for easier access for removal. In revision THA with an ETO, place a cerclage wire prior to reaming and retighten prior to stem insertion. Even with careful surgical technique intra-operative femoral fractures will still occur. When inserting the stem, a sudden change in resistance is highly suggestive of fracture. Wide exposure of the entire proximal femur is necessary to confirm the diagnosis. The distal extent of the fracture must be seen. Only on occasion is an intra-operative radiograph needed. Management is directed to ensuring component stability and good fracture fixation. In primary total hip arthroplasty, calcar fractures are by far the most common. If using proximal fixation and you are certain the stem is stable, then all that is needed is cerclage wiring. As already mentioned, you must follow the fracture line distally so you are aware of how far down it goes. Often what appears to be a calcar split actually propagates distal to the lesser trochanter. In these cases, one would probably go for distal fixation plus wiring. In conclusion, intra-operative femoral fractures are on the rise. Prevention is the key

Introduction. The optimal bearing for hip arthroplasty is still a matter of debate. in younger and more active patients ceramic-on-polyethylene (CoP) bearings are frequently chosen over metal-on-polyethylene (MoP) bearings to reduce wear and increase biocompatibility. However, the fracture risk of ceramic heads is higher than that of metal heads. This can cause serious issue, as ceramic fractures pose a serious complication often necessitating major revision surgery – a complication more frequently seen in ceramic-on-ceramic bearings. To date, there are no long-term data (> 20 years of follow-up) reporting fracture rates of the ceramic femoral heads in CoP bearings. Patients and Methods. We retrospectively evaluated the clinical and radiographic results of 348 cementless THAs treated with 2nd generation Biolox® Al2O3 Ceramic-on-Polyethylene (CoP) bearings, which had been consecutively implanted between January 1985 and December 1989. At implantation the mean patient age was 57 years. The cohort was subsequently followed for a minimum of 20 years. At the final follow-up 111 patients had died, and 5 were lost to follow-up (Fig. 1). A Kaplan-Meier survivorship analysis was used to estimate the cumulative incidence of ceramic head fractures over the long-term. Results. (Figs. 2, 3):. After 22-years the cumulative incidence of ceramic head fracture was estimated at 0.3% (95%-CI, 0–2.4%; 38 hips at risk). No impending failures could be noted on radiographic analysis at final follow-up. Discussion. The fracture rate of second-generation ceramic heads using a CoP articulation remains very low into the third decade after cementless THA; ceramic heads appear to be a safe alternative to metal femoral heads. Summary. This study evaluates the long-term (20–25 year) survivorship of cement on polyethylene bearings in uncemented THA

The purpose of this study was to evaluate in vivo fit and fill analysis of tapered wedge-type stem in total hip arthroplasty (THA) with computed tomography (CT)-based navigation system. 100 THAs were all performed through the posterolateral approach, with patients in the lateral decubitus position. Each cohort of 50 consecutive primary cementless THAs with was compared with and without CT-based navigation system. The post-operative antero-posterior (AP) hip radiographs were obtained two weeks after the operation. All radiographic fit and fill measurements in the proximal and distal areas were analyzed by two of the authors who were both blinded to the use of CT-based navigation system. The type of the fit in the cementless stem was divided into three types. The fit of the stem was classified as Type I, if there was both proximal and distal engagement (maximum proximal to distal engagement difference of 2 mm or greater), Type II when there was proximal engagement only, and Type III when there was distal engagement only. The fill parameters such as mean stem-to-canal ratios and mean minimum and maximum gaps between the stems to the cortical bone in proximal and distal sections were compared. There was a significantly better overall canal fit obtained by THA with CT-based navigation system compared to without the navigation system (p<0.01). With CT-based navigation system, 42 of 50 stems (84%) were categorized as Type I fit compared to 31 of 50 stems (62%) without the navigation system. As to Type II fit, There are significantly more stems without the navigation system (26%) compared to with it (12%). There were better canal fills of the stems obtained by THA with CT-based navigation system both in proximal (94%) and distal sections (88%) of the femur compared to without the navigation system (proximal 88%/distal 82%) (p<0.05). Excellent radiographic fit and fill has been previously reported to potentially correlate with improved clinical outcomes. The stems obtained by THA with CT-based navigation system had a significantly better canal fit demonstrated by higher proportion of Type I and lower proportion of Type II fits, compared to without the navigation system. The stems with the navigation system had also significantly better proximal and distal canal fill

Total hip arthroplasty (THA) is frequently performed as a salvage procedure for the acetabular fracture when posttraumatic osteoarthritis, posttraumatic avascular necrosis, or fixation failure with subluxation develop. Special considerations for this situation include previous surgical exposure with dense scar tissue, the type and location of implants, the location and amount of heterotopic ossification, indolent infection, previous sciatic nerve palsy, and the pathoanatomy of existing acetabular defect. These factors can influence the choice of surgical exposure and the reconstructive method. The outcomes of THA after acetabular fracture are generally less favorable than those of the nontraumatic degenerative arthritis. Reason for this high failure is the low mean age and the high activity level of the patient. Other important reasons for failure include the problem of acetabular bone deficiency and compromised bone quality. We evaluated the results of cementless THA in patient who had previous acetabular fracture. We also compared this result with those of patients with posttraumatic avascular necrosis of the femoral head. Forty-five consecutive cementless THAs were performed for the treatment of post-traumatic osteoarthritis after acetabular fracture between December 1993 and December 2008. Of these patients, 15 patients were died or lost to follow-up monitoring before the end of the minimum one year follow-up period. This left 30 patients (30 hips) as the subjects of our retrospective review. We evaluated the clinical and radiographic results of these patients and compared with the results of THA in patients with post-traumatic AVN of the femoral head which had without acetabular damage. Two hips required revision of the cup secondary to early migration of the acetabular cup (1 hip) and postoperative deep infection (1 hip). There was no significant difference in clinical and radiographic results between two groups except implanted acetabular component size and required bone graft (p<0.05). The Kaplan-Meier ten-year survival rate, with revision as the end-point, was 90% and 96.7% with loosening of acetabular component as the end-point. Our series suggested that compared with cemented components, uncemented sockets may improve the results of arthroplasty after previous acetabular fracture. In conclusion, cementless THA following acetabular fracture presents unique challenge to the surgeon, careful preoperative assessment and secure component fixation with proper bone grafting is essential to minimize problems

Second-generation metal-on-metal bearings have been used since the late 1980s as alternative bearings to eliminate aseptic loosening due to polyethylene wear. The aim of the present study was to evaluate the long-term results of a series of Metasul (Zimmer GmbH, Winterthur, Switzerland) metal-on-metal total hip arthroplasty (THA). Between January 1993 and September 1996, 149 cementless THAs with a 28 mm Metasul articulation were performed in 111 consecutive patients. Implant survivorship was calculated and clinical and radiographic evaluations were performed on 82 hips still available for follow-up at a mean of 18 years postoperatively. Nine hips (6.0%) were revised. The cumulative probability of survival of the overall implant at 18 years postoperatively with revision for any reason as the end point, was 0.937 (95% confidence interval, 0.888 to 0.985). The cumulative probability of survival of Metasul with revision for any reason as the end point, was 0.956 (95% confidence interval, 0.916 to 0.997). Various degrees of radiolucencies and osteolysis were found proximally around the femoral components of 25 hips (20%). Cementless Metasul THA showed high survival at 18 years postoperatively

Background/Purpose. Total hip arthroplasties (THAs) with ceramic bearings are widely performed in young, active patients and thus, long-term outcome in these population is important. Moreover, clinical implication of noise, in which most studies focused on ‘squeaking’, remains controversial and one of concerns unsolved associated with the use of ceramic bearings. However, there is little literature regarding the long-term outcomes after THAs using these contemporary ceramic bearings in young patients. Therefore, we performed a long-term study with a minimum follow-up of . 1. 5 years after THAs using contemporary ceramic bearings in young patients with osteonecrosis of the femoral head (ONFH) less than fifty. Materials and Methods. Among sixty patients (71 hips) with a mean age of 39.1 years, 7 patients (7 hips) died and 4 patients (4 hips) were lost before 15-year follow-up. The remaining 60 hips were included in this study with an average follow-up period of 16.3 years (range, 15 to 18). All patients underwent cementless THA using a prosthesis of identical design and a 28-mm third-generation alumina head by single surgeon. The clinical evaluations included the modified Harris hip score (HHS), history of dislocation and noise around the hip joint: Noise was classified into squeaking, clicking, grinding and popping and evaluated at each follow-up. Snapping was excluded through physical examination or ultrasonography. Radiographic analysis was performed regarding notching on the neck of femoral component, loosening and osteolysis. Ceramic fracture and survivorship free from revision were also evaluated. Results. The mean Harris hip score improved from 55.3 to 95.5 points (range, 83 to 100) at the time of the final follow-up. Seventeen patients (34.7%) reported noise around the hip joint: “squeaking” in one and “clicking” in 16 patients. Notching on the neck of femoral component suggesting impingement between neck and ceramic liner was demonstrated in 9 hips (15%) at average of 6.9 years postoperatively and located at 2 to 3.5 mm distal to edge of ceramic head. Although no chip fracture of ceramic ‘liner’ occurred, notching was associated with “clicking” sound (p<0.01). One patient who reported clicking sound underwent a revision THA because of ceramic ‘head’ fracture. Loosening, osteolysis or dislocation was not observed in any hip and survivorship free from revision at 5 years was 98%. Conclusion. Cementless THAs using 28-mm contemporary alumina ceramic head demonstrated excellent long-term outcome in young, active patients with ONFH. Despite this encouraging result, however, we remain concerned about ‘clicking’ sound, because we did observe it associated with notching on the neck of stem. Acknowledgement. This work was supported by Institute for Information & communications Technology Promotion (IITP) grant funded by the Korea government (MSIP) (#B0101-14-1081)

Ceramic-on-ceramic bearings provide a solution to the osteolysis seen with traditional metal-on-polyethylene bearings. Sporadic reports of ceramic breakage and squeaking concern some surgeons and this bearing combination can show in vivo signs of edge loading wear which was not predicted from in vitro studies. Taper damage or debris in the taper between the ceramic and metal may lead to breakage of either a ceramic head or insert. Fastidious surgical technique may help to minimise the risk of ceramic breakage. Squeaking is usually a benign complication, most frequently occurring when the hip is fully flexed. Rarely, it can occur with each step of walking when it can be sufficiently troublesome to require revision surgery. The etiology of squeaking is multifactorial origin. Taller, heavier and younger patients with higher activity levels are more prone to hips that squeak. Cup version and inclination are also relevant factors. Fifty-five ceramic bearings revised at our center were collected over 12 years. Median time to revision was 2.7 years. Forty-six (84%) cases had edge loading wear. The median femoral head wear volume overall was 0.2mm. 3. /yr, for anterosuperior edge loading was 2.0mm. 3. /yr, and the median volumetric wear rate for posterior edge loading was 0.15mm. 3. /yr (p=0.005). Osteolysis following metal-on-polyethylene total hip arthroplasty (THA) is well reported. Earlier generation ceramic-on-ceramic bearings did produce some osteolysis, but in flawed implants. As 3rd and now 4th generation ceramic THAs come into mid- and long-term service, the orthopaedic community has begun to see reports of high survival rates and very low incidence of osteolysis in these bearings. The technique used by radiologists for identifying the nature of lesions on Computed Tomography (CT) scan is the Hounsfield score which will identify the density of the tissue within the lucent area. Commonly the radiologist will have no access to previous imaging, especially pre-operative imaging if a long time has elapsed. With such a low incidence of osteolysis in this patient group, what, then, should a surgeon do on receiving a CT report on a ceramic-on-ceramic THA, which states there is osteolysis? This retrospective review aims to determine the accuracy of CT in identifying true osteolysis in a cohort of long-term 3rd generation ceramic-on-ceramic uncemented hip arthroplasties in our department. Methods. Pelvic CT scans were performed on the first 27 patients from a cohort of 301 patients undergoing 15-year review with 3rd generation alumina-alumina cementless THAs. The average follow-up was 15 years (15–17). The CT scans were reviewed against pre-operative and post-operative radiographs and reviewed by a second musculoskeletal specialist radiologist. Results. Eleven of the CT scans were reported to show acetabular osteolysis, two reported osteolysis or possible pre-existing cyst and one reported a definitive pre-existing cyst. After review of previous imaging including pre-operative radiographs, eleven of the thirteen patients initially reported to have osteolysis were found to have pre-existing cysts or geodes in the same size and position as the reported osteolysis, and a further patient had spot-welds with stress-shielding. One patient with evidence of true osteolysis awaits aspiration or biopsy to determine if he has evidence of ceramic wear or metallosis. Conclusions. Reports of osteolysis on CT should be interpreted with care in modern ceramic-on-ceramic THA to prevent unnecessary revision. Further imaging and investigations may be necessary to exclude other conditions such as geodes, or stress shielding which are frequently confused with osteolysis on CT scans

Introduction. Osteloysis following metal-on-UHMW polyethylene Total Hip Arthroplasty (THA) is well reported, as is lack of osteolysis following Ceramic-on-Ceramic (CoC)THA. Early ceramic failures did report some osteolysis, but in flawed implants. As 3rd and now 4th generation ceramic THAs come into mid- and long-term use, the orthopaedic community has begun to see reports of high survival rates and very low incidence of osteolysis in these bearings. Osteolysis reported after 3rd generation CoC THA often included metallosis due to neck rim impingement. In our department we have revised only 2 hips in over 6000 CoC THAs for osteolysis. Both had evidence of metallosis as well as ceramic wear. The technique used by Radiologists for identifying the nature of lesions on CT is the Hounsfield score which will identify the density of the tissue within the lucent area. It is common for radiologist to have no access to previous imaging, especially pre-operative imaging if a long time has elapsed. With such a low incidence of osteolysis in this patient group, what, then, should a surgeon do on receiving a CT report on a ceramic-on-ceramic THA which states there is osteolysis? Revision of such implants in elderly patients has a high risk of morbidity and mortality. Objectives. This retrospective review aims to determine the accuracy of CT in identifying true osteolysis in a cohort of long-term third generation ceramic-on-ceramic uncemented hip arthroplasties in our department. Methods. Pelvic CT scans were performed on the first 27 patients from a cohort of 301 patients undergoing 15 year review with 3rd generation alumina-alumina cementless THAs. The average follow-up was 15 years (15–17). The CT scans were reviewed against pre-operative and post-operative radiographs and reviewed by a second musculoskeletal specialist radiologist. Results. Eleven of the CTscans were reported to show acetabular osteolysis, two reported osteolysis or possible pre-existing cyst and one reported a definitive pre-existing cyst. After review of previous imaging including pre-operative radiographs, eleven of the thirteen patients initially reported to have osteolysis were found to have pre-existing cysts or geodes in the same size and position as the reported osteolysis, and a further patient had spot-welds with stress-shielding. One patient with evidence of true osteolysis awaits aspiration or biopsy to determine if he has evidence of ceramic wear or metallosis. Conclusions. Reports of osteolysis on CT should be interpreted with care in modern ceramic-on-ceramic THA to prevent unnecessary revision. Further imaging and investigations may be necessary to exclude other conditions such as geodes, or stress shielding which are frequently confused with osteolysis on CT scans

Introduction. In order to reduce polyethylene wear and incidence of osteolysis, and improve the long-term durability of total hip arthroplasty (THA), highly cross-linked polyethylene was introduced for clinical use in substitution for conventional polyethylene. We performed 35 cementless THAs between December 2000 and February 2002, and cross-linked polyethylene was used in these surgeries. The purpose of this study is to research linear wear rate of these hips, and to find the risk factor for high wear rate. Patients and Methods. 32 hips (26 patients) among the 35 could be evaluated at more than 10 years postoperatively. One hip required reoperations due to infection at 8 years postoperatively, and two were lost to followup in less than 10 years. There were 2 males and 24 females, and the observation period was 11.4 years in average (range 10?13 years). The age at the time of operation was 49.4 years in average (range 24?67 years), and body mass index was 22.4 in average (15?34). We used AHFIX total hip prostheses (KYOCERA Medical Corporation) for both acetabular and femoral replacement, and 22 mm Zirconia head was used in all cases. The median cup diameter was 46 mm (range 42?50). Osteolysis and loosening of the implant was evaluated on the anteroposterior radiograph of the hip. Using software for wear measurement (Hip Analysis Suite), linear wear rate and cup inclination angle were measured. Correlation between linear wear rate and age, BMI, cup inclination angle, and cup diameter was investigated using correlation coefficient. Results. Osteolysis and loosening were not found in any cases on the final radiograph. Cup inclination angle was 44.7±4.6 degree, and linear wear rate was 0.034±0.019 mm/y in average. No statistical correlation was found between linear wear rate and age, BMI, cup inclination angle, and cup diameter. Discussion. Long-term clinical performance of cross-linked polyethylene is rarely reported, although it is considered to have excellent wear resistance, and reduces the risk of osteolysis and loosening. Linear wear rate in this series was relatively low, and osteolysis and loosening were not observed. It was demonstrated that cross-linked polyethylene had excellent wear resistance when used in combination with 22 mm zirconia head, and observed for more than 10 years

Objectives. The purpose of the present study was to describe the long-term results of THA for ONFH in patients with SLE. Methods. From 1994–2001, 18 cementless THAs (14 SLE patients) were included in the present study. Four hips (3 patients) were lost to follow-up. The remaining 14 hips (11 patients) were available for evaluation. The mean follow-up period was 13.1(range, 10.0–16.4) years. The follow-up rate was 77.8%. The mean age at the time of surgery was 35.2 (range, 27.4–51.0) years. Results. Mean preoperative Harris Hip Score was 37.4 (range, 17.1–63.1) points, which improved to 94.5 (range, 73.9–100) points at final follow-up. Two hips had dislocation and were treated successfully with closed reduction. No patient in this study group had deep venous thrombosis or pulmonary embolism. One hip had peroneal nerve palsy. No superficial or deep wound infection was observed. Two hips of 2 patients required reoperation due to dislodgement of a polyethylene insert. With revision of the acetabular component for any reason considered to be a failure, the 10-year survival rate was 93% (95% CI, 0.79–1). Conclusion. We have reported the long-term results of THA for ONFH with SLE. Although several reports have noted that the results of THA for ONFH are less favourable than those for osteoarthritis, the long-term results of THA for ONFH with SLE were acceptable. THA is an acceptable option for patients with advanced-stage or an extended region of ONFH

Introduction. Acute infection following Total Hip Arthroplasty (THA) is a serious complication. It is commonly treated by irrigation and debridement (I&D) with component retention (exchange only the mobile parts of the joint - head and liner). However, the reported re-infection rate with the use of this approach remains high. We are reporting our experience in using single - stage revision arthroplasty in treating acute infection of THA. We hypothesized that the infection control rate after immediate early revision for acute infection of cementless implants is better than has been reported for I&D with exchange of mobile parts. Methods. From our infection arthroplasty database, we reviewed the outcome of 19 patients who had an acute infection (within 6 weeks) of cementless THA. Our management strategy includes I&D and single-stage (direct-exchange) revision arthroplasty followed by 6 weeks course of culture specific oral antibiotics. Results. Patients' average age was 64 year (39–85), M:F = 11:8. There were 13 primary and 6 revision cementless THAs. Average time from the index operation to the development of clinical symptoms of infection was 18 days (4–41). 14 patients (73.7%) were successfully treated with single stage revision strategy with no evidence of re-infection at 64.3 (32–89) months of follow up. 5 patients (26.3%) developed re-infection requiring two stage-revision surgery. Discussion. Our results showed that single stage revision strategy has a better outcome in treating acute infection after THR than the outcomes reported for I&D with component retention. When faced with acute infection of a cementless implant, early implant exchange prior to ingrowth should be considered

Introduction:. Although cementless total hip arthroplasty (THA) is well accepted, the optimal femoral component design remains unknown. Among early complications, loosening and periprosthetic fracture persist and are related to implant design. The purpose of this study is to compare the anatomic fit and early subsidence of two different stem designs: a modern, short taper-wedge design and a traditional fit-and-fill design. Methods:. A retrospective cohort study of 129 consecutive cementless THAs using two different femoral stems was performed. A modern taper-wedge stem was used in 65 hips and a traditional proximal fit-and-fill stem was used in 64 hips. Radiographic analysis was performed at preoperative, immediate postoperative and 1-month postoperative intervals. The radiographic parameters of bone morphology via the canal-flare index, implant subsidence at 1 month, sagittal alignment, and the “anatomic fit” metrics of canal fill and associated gaps were measured and recorded. Results:. There were no differences between groups in patient demographics (p > 0.4), and in bone morphology via the canal-flare index (p = 0.6) with numbers available. The mean subsidence was less in the taper-wedge design at 0.27 mm compared to 1.1 mm in the fit-and-fill stem (p < 0.0001). Subsidence greater than 2 mm occurred in 26 of 64 fit-and-fill stems (41%) compared to 1 of 65 taper-wedge implants (1.5%). The percentage fill at all levels measured was greater in the taper-wedge design (p < 0.0001). The taper-wedge design was inserted a mean of 2.7° sagittal extension compared to 0.4° in the fit-and-fill design (p < 0.0001). Conclusion:. Despite being shorter in length, the taper-wedge design demonstrates greater axial stability and less subsidence compared to a traditional fit-and-fill stem. The optimized proximal femoral fit inherent in this anatomic-based taper-wedge design is likely responsible for the minimal subsidence. The clinical implication of greater extension in the sagittal plane is unknown and longer-term clinical follow up is warranted

INTRODUCTION. The purpose of this study is to elucidate longitudinal kinematic changes of the hip joint during heels-down squatting after THA. METHODS. 66 patients with 76 primary cementless THAs using a CT-based navigation system were investigated using fluoroscopy. An acetabular component and an anatomical femoral component were used through the mini-posterior approach with repair of the short rotators. The femoral head size was 28mm (9 hips), 32mm (12 hips), 36mm (42 hips), and 40mm (12 hips). Longitudinal evaluation was performed at 3 months, 1 year, and 2≤ years postoperatively. Successive hip motion during heels-down squatting was recorded as serial digital radiographic images in a DICOM format using a flat panel detector. The coordinate system of the acetabular and femoral components based on the neutral standing position was defined. The images of the hip joint were matched to 3D-CAD models of the components using a2D/3D registration technique. In this system, the root mean square errors of rotation was less than 1.3°, and that of translation was less than 2.3 mm. We estimated changes in the relative angle of the femoral component to the acetabular component, which represented the hip ROM, and investigated the incidence of bony and/or prosthetic impingement during squatting (Fig.1). We also estimated changes in the pelvic posterior tilting angle (PA) using the acetabular component position change. In addition, when both components were positioned most closely during squatting, we estimated the minimum angle (MA) up to theoretical prosthetic impingement as the safety margin (Fig.2). RESULTS. No prosthetic or bony impingement and no dislocation occurred in any hips. The mean maximum hip flexion ROM was 92.4° (range, 76.6° – 107.9°) at 3 months, 103.4° (range, 81.5° – 115.2°) at 1 year, and 102.4° (range, 87.1° – 120.6°) at 2≤ years (3 months vs 1 year, p<0.05; 1 year vs 2≤ years, p>0.05, paired t-test). The mean PA was 26.7° (range, 0.9° – 49.8°) at 3 months, 21.7° (range, 3.4° – 43.8°) at 1 year, and 21.2° (range, −0.7° – 40.4°) at 2≤ years (3 months vs 1 year, p<0.05; 1 year vs 2≤ years, p>0.05). The mean flexion ROM and MA at 2≤ years were 98.4±20.8° and 14.3±7.3° in 28 mm heads, 102.3±10.7° and 15.6±4.8° in 32 mm heads, 102.8±14.5° and 20.3±9.6° in 36 mm heads, and 103.2±16.9° and 23.4±10.9° in 40 mm heads, respectively. There were no significant differences in the hip flexion ROM between 28, 32, 36, and 40 mm head cases, whereas MA significantly increased as the femoral head diameter was larger (p<0.05, unpaired t-test). DISCUSSION AND CONCLUSION. Three-dimensional assessment of dynamic squatting motion after THA using the 2D/3D registration technique enabled us to elucidate longitudinal kinematic change of the hip joint. Longitudinal kinematic analysis indicated that hip flexion ROM and posterior tilt during squatting changed significantly by 1 year postoperatively, and there were no significant changes after 1 year while safety margin kept > 10°. For figures/tables, please contact authors directly.

Introduction. Bi-Metric® cementless primary stem is tapered, rounded conical shaped and coated with plasma spray porous to one-third from the proximal. Fixation is achieved by a press-fit insertion in the Metaphyseal-diaphyseal junction. From 1986 until now, nearly 700 Bi-Metric® stems have been implanted at our hospital. The purpose of this study was to present the clinical and radiological findings including a survival analysis of a consecutive Bi-Metric® stems series followed for over 10 years. Materials and methods. 112 primary cementless THAs in 96 patients using the Bi-Metric® femoral tapered stem were available for clinical and radiological evaluation with a minimum follow-up of ten years. Malloy-Head 4-fined acetabular cup was used in all hips. Follow-up was at a mean of 13 years. We applied THA in 84 patients for osteoarthritis, in 6 avascular necrosis for the femoral head and in 6 for rheumatoid arthritis. The mean age of the patients was 59.5 years. Clinically, pain ROM walking and ADL were evaluated according to the Japanese association hip (JOA) score, and complications and survivorship were investigated. Radiographic results were described according to the 7 femoral Gruen zones. Stem fixation in accordance with the method of Engh at al, cancellous condensation, reactive line, osteolysis, stem subsidence, and bone atrophy with stress shielding were examined. Wear was measured according to the method described by Livermore et al., and the effect of the wear on osteolysis was investigated. Results. The mean JOA score at follow-up was 93.5 points. No early loosening and no fracture of the implant were found. Tow hips underwent revision surgery, one for a late deep infection, and another one for recurrent dislocation. The overall survival was 98.2% at 13 years. Survival with femoral revision for aseptic loosening as an endpoint was 100%. No subsidence was seen in follow-up period. The mean Engh score for fixation was 9.3 and for stability was 16.8. Focal osteolysis was noted in 20.6% of the hips. In most cases, they were located proximally in zones 1 and 7. The appearance of osteolysis was correlated with PE linear wear. Discussion. The results for mid- to long-term survival with this femoral component are encouraging. However focal osteolysis attributed to PE wear was seen in one-fifth of the hips and there is a concerned risk that progressing osteolysis causes the loosening in the future. We believe that if the PE wear is reduced, further longevity of this stem will be realized

Purpose. There has been recent interest in gender-specific arthroplasty implant design but little evidence to support their use. We hypothesised that outcomes among arthroplasty patients are affected by gender. Methods. Patients were retrospectively identified from a prospective database of TJRs performed at one centre among six surgeons over a ten-year period (1998-2008). Demographics, pre-operative and 1-year clinical Knee Society (KSS), Harris Hip (HHS), and Oxford scores were collected. Gender differences were analysed using independent samples t-test and chi-square. Results. The study sample was comprised of 4780 primary unilateral TJRs performed for osteoarthritis, including 3186 cemented TKAs (63% females, 37% males), and 1594 cementless THAs (55% females, and 45% males). Among TKAs, females had higher BMIs, and differing rates of comorbidities and complications. Female KSS, Oxford and flexion scores were significantly inferior to male scores pre-operatively and at 1-year follow-up. Significantly more females reported higher pain scores and inferior stair climbing ability compared to males at all intervals. Females showed significantly more improvement in clinical outcomes, including flexion from pre-operative to one-year. Among THAs, females were significantly younger with higher BMIs. There were varying rates of complications and comorbidities by gender. Females had significantly worse HHS and Oxford scores, and inferior stair climbing ability at all intervals. Pain scores were higher for females pre-operatively and at 6 weeks, but became equivalent thereafter. Females showed significantly greater outcomes improvement pre-operative to one-year. Conclusion. As reported in the literature, results of this study indicate that women choose arthroplasty at a later stage of disease, presenting with inferior functional status. The effect of waiting seems most marked among the TKA population with inferior outcomes and pain relief persisting to one year. Although women do have inferior outcomes, their overall level of improvement is superior. Surgeons must counsel females differently about expectations and TJR recovery

Purpose. Ceramic-on-ceramic bearings in total hip arthroplasty (CoC THA) have theoretical advantages of wear resistance and favorable biocompatibility of ceramic particles to the surrounding bony and soft tissue. Long-time durability of CoC THA has been expected, however, clinical results over 10 years after operation were scarcely reported. In the present study, clinical results at follow of 10 years were examined for CoC THAs with a changeable femoral neck which allowed correction of anteversion of the femoral component in cases with abnormal femoral anteversion in dysplastic hips. Methods. During 1997 and 2000, 203 cementless CoC THAs in 158 patients were conducted in our hospital. Six patients died because of unrelated causes and 5 patients were lost to followup, and the remaining 188 hips in 147 patients were analyzed at the mean followup period of 10.8 years (3.7 to 13.5). There were 24 men and 123 women, and the average age at operation was 54 years (26 to 73). The hip diseases for operation were osteoarthritis in 165 hips, osteonecrosis of the femoral head in 21 hips and failure of hemiarthroplasty in 2 hips. The operation was performed in the lateral position through the posterior approach without trochanteric osteotomy. The articulation was composed of Biolox forte alumina liner fitted into beads-coated hiemispherical titanium shell, and a 28-mm Biolox forte alumina femoral head (Cremascoli). The femoral component was either AnCA stem or custom-designed stem, coupled with a modular neck allowing selection of 5 variable offsets and anteversions (Cremascoli). Clinical and radiological findings, and complications during the followup period were analyzed. Results. During the follow-up, 8 hips were revised, due to repeated dislocation (2 hips), periprosthetic fracture (1 hips), cup loosening (1 hip), fracture of ceramic liner rim (2 hips), and cup loosening along with ceramic liner rim fracture (2 hips). Cup abduction angle of the 4 cases with ceramic liner rim fracture were high at 49 degrees or more, as compared with the mean cup abduction angle of 41 degrees in the other hips without ceramic fracture. The survival rate at 10 years was 96.0 % when failure was revision. In the hips other than the revised cases, 6 hips showed cup loosening and no hip showed stem loosening on radiographs. Osteolysis was seen in 3 hips around the cup and 4 hips around the stem. Nineteen patients (10%) complained of abnormal noises around the hip, but most of the noises were click sound. Discussion. The 10-year results of cementless CoC THAs with a modular neck were favorable with few cases of osteolysis. However, relatively high frequency of cup loosening may be a concern, since increased cup abduction angle associated with cup loosening may cause ceramic liner fracture

The in vivo kinematics of squatting after total hip arthroplasty (THA) has remained unclear. The purpose of the present study was to elucidate range of motion (ROM) of the hip joint and the incidence of prosthetic impingement during heels-down squatting after THA. 23 primary cementless THAs using a computed tomography-based navigation system (CT-HIP, Stryker Navigation, Freiberg, Germany) were investigated using fluoroscopy. An acetabular component with concavities around the rim (TriAD HA PSL, Stryker Orthopaedics, Mahwah, NJ) and a femoral component with reduced neck geometry (CentPiller, Stryker Orthopaedics), which provided a large oscillation angle, were used. The femoral head size was 28mm (8 hips), 32mm (10 hips), and 36mm (5 hips). Post-operative analysis was performed within 6 months in 6 hips, and at 6 months to 2 years in 17 hips. Successive hip motion during heels-down squatting was recorded as serial digital radiographic images in a DICOM format using a flat panel detector. The coordinate system of the acetabular and femoral components based on the neutral standing position was defined. The images of the hip joint were matched to three-dimensional computer aided design models of the acetabular and femoral components using a two-dimensional to three-dimensional (2D/3D) registration technique. In the previous computer simulation study of THA, the root mean square errors of rotation was less than 1.3°, and that of translation was less than 2.3 mm. We estimated changes in the relative angle of the femoral component to the acetabular component, which represented the hip ROM, and investigated the incidence of prosthetic impingement during squatting. We also estimated changes in the flexion angle of the acetabular component, which represented the pelvic posterior tilting angle (PA), and the flexion angle of the femoral component, which represented the femoral flexion angle (FA). The contribution of the PA to the FA at maximum squatting was evaluated as the pelvic posterior tilting ratio (PA/FA). In addition, when both components were positioned most closely during squatting, we estimated the minimum angle (MA) up to theoretical prosthetic impingement. No prosthetic impingement occurred in any hips. The maximum hip flexion ROM was mean 92.7° (SD; 15.7°, range; 55.1°–119.1°) and was not always consisted with the maximum squatting. The maximum pelvic posterior tilting angle (PA) was mean 27.3° (SD; 11.0°, range; 5.5°–46.5°). The pelvis began to tilt posteriorly at 50°–70° of the hip flexion ROM. The maximum femoral flexion angle (FA) was mean 118.9° (SD; 10.4°, range; 86.4°–136.7°). At the maximum squatting, the ratio of the pelvic posterior tilting angle to the femoral flexion angle (pelvic posterior tilting ratio, PA/FA) was mean 22.9% (SD; 10.4%, range; 3.8%–45.7%). The minimum angle up to the theoretical prosthetic impingement was mean 22.7° (SD; 7.5°, range; 10.0°–37.9°). The maximum hip flexion of ROM in 36 mm head cases was larger than that in 32 mm or 28 mm head cases, while the minimum angle up to the prosthetic impingement in 36 mm head cases was also larger than that in 32 mm or 28 mm head cases. Three-dimensional assessment of dynamic squatting motion after THA using the 2D/3D registration technique enabled us to elucidate hip ROM, and to assess the prosthetic impingement, the contribution of the pelvic posterior tilting, and the minimum angle up to theoretical prosthetic impingement during squatting

Background. Total Hip Arthroplasty (THA) using the Direct Anterior Approach (DAA) is a muscle sparing approach which promotes early mobilisation of patients. It is a technically challenging approach shown to have a high rate of complications, especially during the learning curve. Here we present the results of 157 cases of THA via a DAA on a standard theatre table, with a minimum of 6 months follow-up. Materials & Methods. The authors conducted a prospective study on a group of 149 consecutive patients undergoing 157 cementless primary THAs for coxarthrosis, 8 bilateral. The same surgical technique was used in all patients, performed by the senior author WLW at a single centre. The average age of the patients at time of surgery was 69 years, 78% were female and 57% were right sided. All implants were uncemented, with bearings being ceramic on ceramic or Ceramic on highly cross-linked polyethylene. Patients were assessed clinically and radiographically pre- and post-operatively at 6 weeks, 6 months, 1 and 2 years. Intra-operatively, navigation was used to guide cup position and assess offset and leg length. Results & Discussion. At the time of the latest follow-up, 1 patient had died of unrelated cause and 8 (5%) were lost to follow-up Clinically, the mean Harris Hip Score was 91 points with 88% reporting a good or excellent result, with 5% reporting moderate to severe pain. Radiographically all patients assessed had evidence of stable bony ingrowth. There was subsidence of 2–5mm in 9 stems (6%). Osteolysis was reported adjacent to one cup and one stem. There were no dislocations. The complication rate was 4.5%. This included 2 intra-operative femoral fractures, one a minor greater trochanteric fracture not requiring fixation, the other a calcar fracture treated at time of surgery. There were 3 femoral fractures occurring on average 4 weeks after surgery all requiring revision and one stem subsidence of 10mm following a heavy fall, subsequently requiring revision for leg length discrepancy. Other complications included one non-fatal PE, a haematoma that required evacuation. We report 20 (12%) episodes of lateral femoral cutaneous nerve palsy of any severity, most of which had or were resolving at the 6 month follow-up. Kaplan Mieir survival analysis was 97.2% at minimum 6 months. Patients mobilised day of surgery or day 1 post-op, and were discharged on average day 4 post-op. Neither the intra- or post-operative fractures could be attributed to the learning curve. Similarly episodes of stem subsidence and LFCN palsy occurred spread out over the 3 years of the study. This study supports the existing orthopaedic literature reporting the benefits of the DAA for THA with reduced soft tissue damage, reduced blood loss and early mobilisation with a low incidence of dislocation. Other authors however have reported a high incidence of complications attributing them to the early learning curve. This early study of DAA using a standard theatre table has identified that complications of fracture, stem subsidence and LFCN injury can occur at any time and bear no relationship to a learning curve