Compression and absolute stability are important in the management of intra-articular fractures. We compared tension band wiring with plate fixation for the treatment of fractures of the olecranon by measuring compression within the fracture. Identical transverse fractures were created in models of the ulna. Tension band wires were applied to ten fractures and ten were fixed with Acumed plates. Compression was measured using a Tekscan force transducer within the fracture gap. Dynamic testing was carried out by reproducing cyclical contraction of the triceps of 20 N and of the brachialis of 10 N. Both methods were tested on each sample. Paired t-tests compared overall compression and compression at the articular side of the fracture. The mean compression for plating was 819 N (. sd. 602, 95% confidence interval (CI)) and for tension band wiring was 77 N (. sd. 19, 95% CI) (p = 0.039). The mean compression on the articular side of the fracture for plating was 343 N (. sd. 276, 95% CI) and for tension band wiring was 1 N (. sd. 2, 95% CI) (p = 0.038). During simulated movements, the mean compression was reduced in both groups, with tension band wiring at −14 N (. sd. 7) and for plating −173 N (. sd. 32). No increase in compression on the articular side was detected in the tension band wiring group. Pre-contoured plates provide significantly greater compression than tension bands in the treatment of transverse fractures of the olecranon, both over the whole fracture and specifically at the articular side of the fracture. In tension band wiring the overall compression was reduced and articular compression remained negligible during simulated contraction of the triceps, challenging the tension band principle

We report a case of transverse fracture through the body of the axis. This fracture was unstable, had been produced by extension forces and was managed conservatively. The classification of such fractures is discussed

Aims. Post-traumatic periprosthetic acetabular fractures are rare but serious. Few studies carried out on small cohorts have reported them in the literature. The aim of this work is to describe the specific characteristics of post-traumatic periprosthetic acetabular fractures, and the outcome of their surgical treatment in terms of function and complications. Methods. Patients with this type of fracture were identified retrospectively over a period of six years (January 2016 to December 2021). The following data were collected: demographic characteristics, date of insertion of the prosthesis, details of the intervention, date of the trauma, characteristics of the fracture, and type of treatment. Functional results were assessed with the Harris Hip Score (HHS). Data concerning complications of treatment were collected. Results. Our series included 20 patients, with a mean age of 77 years (46 to 90). All the patients had at least one comorbid condition. Radiographs showed that 75% of the fractures were pure transverse fractures, and a transverse component was present in 90% of patients. All our patients underwent surgical treatment: open reduction and internal fixation, revision of the acetabular component, or both. Mean follow-up was 24 months, and HHS at last follow-up was 75.5 (42 to 95). The principal complications observed were dislocations of the prosthesis (30%) and infections (20%). A need for revision surgery was noted in 30% of patients. No dislocation occurred in patients undergoing osteosynthesis with acetabular reconstruction. We did not note either mechanical loosening of the acetabular component nor thromboembolic complications. In all, 30% of patients presented acute anemia requiring transfusion, and one death was reported. Conclusion. Post-traumatic periprosthetic acetabular fractures frequently have a transverse component that can destabilize the acetabular implant. The frequency of complications, principally dislocations, led to a high rate of revision surgery. Improvements in preoperative planning should make it possible to codify management to reduce this high rate of complications. The best results were obtained when the surgical strategy combined osteosynthesis with acetabular reconstruction. Cite this article: Bone Jt Open 2024;5(1):28–36

Transverse fractures of the sacrum with neurological complications have been studied in four patients illustrating the following features: diagnosis is often delayed, there are radiological difficulties in making the diagnosis, and the indications for surgery are not well defined. Specific radiographic views are recommended. All the cases presented in this report responded well to conservative management

Aims. The aims of this study were to describe the epidemiology of metacarpal shaft fractures (MSFs), assess variation in treatment and complications following standard care, document hospital resource use, and explore factors associated with treatment modality. Methods. A multicentre, cross-sectional retrospective study of MSFs at six centres in the UK. We collected and analyzed healthcare records, operative notes, and radiographs of adults presenting within ten days of a MSF affecting the second to fifth metacarpal between 1 August 2016 and 31 July 2017. Total emergency department (ED) attendances were used to estimate prevalence. Results. A total of 793 patients (75% male, 25% female) with 897 MSFs were included, comprising 0.1% of 837,212 ED attendances. The annual incidence of MSF was 40 per 100,000. The median age was 27 years (IQR 21 to 41); the highest incidence was in men aged 16 to 24 years. Transverse fractures were the most common. Over 80% of all fractures were treated non-surgically, with variation across centres. Overall, 12 types of non-surgical and six types of surgical treatment were used. Fracture pattern, complexity, displacement, and age determined choice of treatment. Patients who were treated surgically required more radiographs and longer radiological and outpatient follow-up, and were more likely to be referred for therapy. Complications occurred in 5% of patients (39/793). Most patients attended planned follow-up, with 20% (160/783) failing to attend at least one or more clinic appointments. Conclusion. MSFs are common hand injuries among young, working (economically active) men, but there is considerable heterogeneity in treatment, rehabilitation, and resource use. They are a burden on healthcare resources and society, thus further research is needed to optimize treatment. Cite this article: Bone Jt Open 2024;5(8):652–661

Purpose of study:. The presence of an L5 transverse process fracture is reported in many texts to be a marker of pelvis fracture instability. There is paucity of literature to support this view. Available studies have been performed on patients who were already known to have a pelvis fracture. No study has attempted to document the presence of this lesion in the absence of a pelvis fracture. Primary aim: To identify the correlation between the presence of a L5 transverse process fracture and an unstable pelvic ring injury. Secondary aim: To establish whether a L5 transverse process fracture can occur in the absence of a pelvis fracture. Methods:. We conducted a retrospective review of all CT scans performed in patients who presented to a Level 1 Trauma Unit for blunt abdomino-pelvic trauma between January 1, 2012 and August 28, 2013. A total of 203 patients met our inclusion criteria. Results:. Fifty four of these 203 patients (26%) sustained a pelvis fracture. Of these 54 patients 26 (48%) had an unstable fracture pattern according to the AO classification. Five of these 26 patients (19%) had an associated L5 transverse process fracture. Seven (12%) had an L5 transverse process fracture associated with a stable fracture pattern. Three patients (1.4%) had an isolated L5 transverse process fracture in the absence of a pelvis fracture. Conclusion:. This study confirms the association between the presence of a L5 transverse process fracture and an unstable pelvis fracture pattern. This injury is rarely seen in the absence of a pelvis fracture so its presence should alert the treating clinicians to the existence of a pelvis fracture

Evidence that L5 transverse process fracture indicates pelvic instability is insufficient and controversial. Because of unstable pelvis fractures have high mortality rate, they require urgent treatment and good follow-up. The lumbar region is also affected by high-energy traumas in the pelvis region, which causes damage to the muscles and ligamentous structures that adhere to the lumbar transverse process. For this reason, L5 transverse process fracture is thought to be an indicator showing pelvic instability. However, our study shows that this is not like that. This study was carried out in order to investigate the effect of L5 transvers process fracture on pelvic instability and lack of sufficient data in the literature. Between 2017–2020, 86 Patient who were hospitalized and treated with a diagnosis of pelvic fracture were retrospectively studied in our clinic. Pelvic X-Ray and tomography was taken pre-op for all patient. Demographic features, pre-op and post-op hemoglobin counts, how many units of blood transfusion needed in total, fixation method, surgical intervention, presence of additional injury, mechanism of injury for all patient were analyzed and the patients were categorized by investigating L5 transvers process fracture in their tomography. Fractures of patients were classified according toTyle classification. The patients were divided into two main groups as who stabil and unstabil pelvic fractures and L5 transvers process fracture and without. On stabil pelvic fractures and unstabil pelvic fractures, in term of instability effects of L5 transvers process fractures and those without were investigated. Also, changes in preop and post op hemoglaobin counts were investigated in pelvis with and without L5 transvers process fractures. With these, in terms of blood transfusion need the patients were evaluated whether there was a difference between those with L5 transvers process fractures and who did not. Again, whether the blood transfusion was statistically different in stable and unstable pelvis fractures was among the parameters looked at. In statistical analysis, no correlation was found between pelvic instability and L5 transvers process fracture. (p=0,933) No statistically significant difference was found in the evalution of blood transfusion between those with and without L5 transvers process fractures. (P=0,409)When the same parameter was evaluated in terms of stability and instability of the pelvis, it was seen that stability did not significantly affect the need for blood transfusion. (P=0,989) Pre-op and post-op hemoglobin changes of the patients who with L5 transvers process fracture and without were also analized. İn the analysis performed, there was no significant difference in patients with and without L5 transvers process fractures on pre-op and post-op hemoglobin values. (p=0.771/p=0.118)However, Postoperative hemoglobin values were significanly lower in patient with L5 transvers process fracture compared to preopetative hemoglobin values. (p=0.001). L5 transvers process fracture is not a parameter to showing pelvic instability. Stabil and unstabil fractures did not change the need for blood transfusion. The literatüre still needs much more study on this topic

Aims. Compression and absolute stability are important in intra-articular fractures such as transverse olecranon fractures. This biomechanical study aims to compare tension band wiring (TBW) with plate fixation by measuring compression within the fracture. Methods. A cross-over design and synthetic ulna models were used to reduce variation between samples. Identical transverse fractures were created using a 0.5mm saw blade and cutting jig. A Tekscan(tm) force transducer was calibrated and placed within the fracture gap. Twenty TBW or Acumed(tm) plate fixations were performed according to the recommended technique. Compression was measured while the constructs were static and during simulated elbow range of movement exercises. Dynamic testing was performed using a custom jig reproducing cyclical triceps contraction of 20N and reciprocal brachialis contraction of 10N. Both fixation methods were tested on each sample. Half were randomly allocated to TBW first and half to plating first. Data was recorded using F-scan (v 5.72) and analysed using SPSS(tm) (v 16). Paired T-tests compared overall compression and compression at the articular side of the fracture. Results. The mean overall compression for plating was 819N (+/− 602N 95%CI), TBW overall compression: 77N (+/−19N 95%CI) (P=0.039). Articular side compression for plating: 343N (+/− 276N 95%CI), TBW: 1N (+/− 2N 95%CI). (P=0.038). During simulated movements, overall compression reduced in both groups: TBW -14N (+/−7N) Plating -173N (+/−32N) and no increase in articular side compression was detected in the TBW group. Conclusion. Precontoured plates such as the Acumed(tm) olecranon system can provide significantly greater compression, compared to TBW in transverse olecranon fractures. This was significant for compression over the whole fracture surface and specifically at the articular side of the fracture. Also, in TBW, overall compression reduced and articular side compression remained negligible during simulated triceps contraction, challenging the tension band principle

Aims. The aim of this study was to report the long-term follow-up of cemented short Exeter femoral components when used in primary total hip arthroplasty (THA). Methods. We included all primary 394 THAs with a cemented short Exeter femoral component (≤ 125 mm) used in our tertiary referral centre between October 1993 and December 2021. A total of 83 patients (21%) were male. The median age of the patients at the time of surgery was 42 years (interquartile range (IQR) 30 to 55). The main indication for THA was a childhood hip disease (202; 51%). The median follow-up was 6.7 years (IQR 3.1 to 11.0). Kaplan-Meier survival analyses were performed to determine the rates of survival with femoral revision for any indication, for septic loosening, for fracture of the femoral component and for aseptic loosening as endpoints. The indications for revision were evaluated. Fractures of the femoral component were described in detail. Results. The 20-year rate of survival was 85.4% (95% confidence interval (CI) 73.9 to 92.0) with revision for any indication, 96.2% (95% CI 90.5 to 98.5) with revision for septic loosening and 92.7% (95% CI 78.5 to 97.6) with revision for fracture of the femoral component. No femoral components were revised for aseptic loosening. There were 21 revisions of the femoral component; most (seven) as part of a two-stage management of infection. Fracture of the femoral component occurred in four THAs (1.0%) at 6.6, 11.6, 16.5, and 18.2 years of follow-up, respectively. Three of these were transverse fractures and occurred at the level of the lesser trochanter. In one THA, there was a fracture of the neck of the component. Conclusion. THAs using cemented short Exeter femoral components showed acceptable rates of survival of the femoral component at long-term follow-up, in this young cohort of patients. Although fracture is a rare complication of these components, surgeons should be aware of their incidence and possible risk factors. Cite this article: Bone Joint J 2024;106-B(3 Supple A):137–142

Aim of this study was to identify reoperation rates in patients with short oblique and transverse fractures around a well fixed cemented polished taper slip stem and to determine any associations with treatment failure. Retrospective cohort study of 31 patients with AO transverse or short oblique Vancouver B1 PFFs around THA (total hip arthroplasty) cemented taper slip stems: 12 male (39%); mean age 74±11.9 (range 44–91); mean BMI 28.5±1.4 (range 16–48); and median ASA 3. Patient journeys were assessed, re-interventions reviewed. The primary outcome measure was reoperation. Time from primary THA to fracture was 11.3±7.8yrs (0.5–26yrs). Primary surgical management was fixation in 27/31 and rTHA (revision total hip arthroplasty) in 4/31. 10 of 31 (32%) patients required reoperation, 9 within 2 years of fracture: 1 following rTHA and 8 following ORIF. The commonest mode of failure was non-union (n=6). No significant associations with reoperation requirement were identified. Kaplan-Meier free from reoperation was 67.4% (49.8–85.0 95% CI) at 2 years and this was unaffected by initial management with ORIF or rTHA (Log rank 0.898). Of those reoperated, 6/10 required multiple reoperations to obtain either bony union or a stable revision construct and 13% ultimately required proximal femoral endoprostheses. The relative risk of 1 year mortality was 1.6 (0.25 to 10.1 95%CI) among patients who required reoperation compared to those who did not. These are difficult fractures to manage, should not be underestimated and patients should be counselled that there is a 30% risk of reoperation and 20% of requiring multiple reoperations

The aim of the study was to report the survival of open reduction and internal fixation (ORIF) of Vancouver B fractures associated with the Exeter Stem (ES) at a minimum of 5 years. This retrospective cohort study assessed 129 consecutive patients with Vancouver B type fractures treated with ORIF from 2008-2016 at a minimum of 5 years. Patient records were examined, and the following recorded: details of primary prosthesis, details of injury, Vancouver classification, details of operative management, complications, and requirement for reoperation. Data was analysed using SPSS. Survival analysis was undertaken using the endpoint ‘reoperation for any reason’. Mean age at fracture was 78.2 (SD10.6, 46-96) and 54 (43%) were female. Vancouver subclassifications were: 24% B1, 70.5% B2 and 5.5% B3. For all Vancouver B fractures, Kaplan Meier analysis demonstrated a 5 year survival free from reoperation of 88.8% (82.0-94.7 95%CI). Fourteen patients required reoperation, most commonly within the first year for non-union and plate fracture (5.4%). Five-year survival for any reoperation differed significantly according to fracture type (p=0.016) and was worst in B1s: B1 76.6% (61.3-91.9); B2 92.6% 986.9-98.3); and 100% of B3. Univariate analysis identified B1 type (p=0.008) and a transverse fracture pattern (p=0.003) to be significantly associated with the need for reoperation. Adopting a strategy of fixation of all Vancouver B fractures involving the ES where the fracture was anatomically reducible and the bone cement interface was well-fixed was associated with a 5 year survival, free from reoperation of 88.8%

Aims. This study evaluates risk factors influencing fracture characteristics for postoperative periprosthetic femoral fractures (PFFs) around cemented stems in total hip arthroplasty. Methods. Data were collected for PFF patients admitted to eight UK centres between 25 May 2006 and 1 March 2020. Radiographs were assessed for Unified Classification System (UCS) grade and AO/OTA type. Statistical comparisons investigated relationships by age, gender, and stem fixation philosophy (polished taper-slip (PTS) vs composite beam (CB)). The effect of multiple variables was estimated using multinomial logistic regression to estimate odds ratios (ORs) with 95% confidence intervals (CIs). Surgical treatment (revision vs fixation) was compared by UCS grade and AO/OTA type. Results. A total of 584 cases were included. Median age was 79.1 years (interquartile range 72.0 to 86.0), 312 (53.6%) patients were female, and 495 (85.1%) stems were PTS. The commonest UCS grade was type B1 (278, 47.6%). The most common AO/OTA type was spiral (352, 60.3%). Metaphyseal split fractures occurred only with PTS stems with an incidence of 10.1%. Male sex was associated with a five-fold reduction in odds of a type C fracture (OR 0.22 (95% CI 0.12 to 0.41); p < 0.001) compared to a type B fracture. CB stems were associated with significantly increased odds of transverse fracture (OR 9.51 (95% CI 3.72 to 24.34); p < 0.001) and wedge fracture (OR 3.72 (95% CI 1.16 to 11.95); p = 0.027) compared to PTS stems. Both UCS grade and AO/OTA type differed significantly (p < 0.001 and p = 0.001, respectively) between the revision and fixation groups but a similar proportion of B1 fractures underwent revision compared to fixation (45.3% vs 50.6%). Conclusion. The commonest fracture types are B1 and spiral fractures. PTS stems are exclusively associated with metaphyseal split fractures, but their incidence is low. Males have lower odds of UCS grade C fractures compared to females. CB stems have higher odds of bending type fractures (transverse and wedge) compared to PTS stems. There is considerable variation in practice when treating B1 fractures around cemented stems. Cite this article: Bone Jt Open 2021;2(7):466–475

Cemented total hip replacement (THR) provides excellent outcomes and is cost-effective. Polished taper-slip (PTS) stems demonstrate successful results and have overtaken traditional composite-beam (CB) stems. Recent reports indicate they are associated with a higher risk of postoperative periprosthetic femoral fracture (PFF) compared to CB stems. This study evaluates risk factors influencing fracture characteristics around PTS and CB cemented stems. Data were collected for 584 PFF patients admitted to eight UK centres from 25/05/2006-01/03/2020. Radiographs were assessed for Unified Classification System (UCS) grade and Arbeitsgemeinschaft für Osteosynthesefragen/Orthopaedic Trauma Association (AO/OTA) type. Statistical comparisons investigated relationships by age, gender, and stem fixation philosophy (PTS versus CB). The effect of multiple variables was estimated using multinomial logistic regression to estimate odds ratios (OR) with 95% confidence intervals (CI). Median (IQR) age was 79.1 (72.0–86.0) years, 312 (53.6%) patients were female, and 495 (85.1%) stems were PTS. The commonest UCS grade was type B1 (278, 47.6%). The commonest AO/OTA type was spiral (352, 60.3%). Metaphyseal-split fractures occurred only with PTS stems with an incidence of 10.1%. Male gender was associated with a five-fold reduction in odds of a type C fracture (OR 0.22, 95% CI 0.12 to 0.41, p<0.001) compared to a type B fracture. CB stems were associated with significantly increased odds of transverse fracture (OR 9.51, 95% CI 3.72 to 24.34, p <0.001) and wedge fracture (OR 3.72, 95% CI 1.16 to 11.95, p <0.05) compared to PTS stems. This is the largest study investigating PFF characteristics around cemented stems. The commonest fracture types are B1 and spiral fractures. PTS stems are exclusively associated with metaphyseal-split fractures, but their incidence is low. Males have lower odds of UCS grade C fractures compared to females. CB stems had higher odds of bending type fractures (transverse and wedge) compared to PTS stems. Biomechanical testing is needed for validation and investigation of modifiable factors which may reduce the risk of unstable fracture patterns requiring complex revision surgery over internal fixation

Periprosthetic femoral fractures are becoming increasingly common and are a major complication of total hip arthroplasty (THA) and bipolar hemiarthroplasty (BHA). We report a retrospective review of the outcomes of treatment of 11 periprosthetic fractures after femoral revision using a long stem. Eleven female patients with a mean age of 79.2 years (70 to 91 years) were treated for a Vancouver type B1 fracture between 1998 and 2013. The status of the initial arthroplasty was THA in 5 patients and BHA in 6 patients. The original diagnosis was femoral neck fracture in 5 patients, osteoarthritis in 5 patients, and avascular necrosis of femoral head in 1 patient. Seven patients had had a cemented femoral component and 4 had had a cementless femoral component. The mean numbers of previous surgeries were 3.2 times (2 to 5 times). A previous history of fracture in the same femur was found in 7 hips including 5 femoral neck fractures, 3 periprosthetic fractures. The cause of the latest revision surgery was aseptic loosening in 6 hips, periprosthetic fracture in 3 hips, and infection in 2 hips. The average time to fracture after femoral revision using a long stem was 106.5 months (12 to 240 months). The average follow-up was 58.9 months (8 to 180 months). The fracture pattern was a transverse fracture in 6 hips and an oblique fracture in 5 hips. The type B1 fractures were treated with open reduction and internal fixation in 9 hips, 6 of which were reinforced with bone grafts. Seven patients were treated with a locking compression plate and cerclage wiring, and 2 patients were treated with a Dall-Miles system. Two other periprosthetic fractures were treated with femoral revision. One was revised because of stem breakage, and the other was a transverse fracture associated with very poor bone quality, which received a femoral revision with a long stem and a locking compression plate. All fractures except one achieved primary union. This failed case had a bone defect at the fracture site, and revision surgery using a cementless long stem and allografts was successful. These finding suggest that a type B1 fracture after revision using a long stem associated with very poor bone quality or bone loss might be considered as a type B3 fracture, and femoral revision might be the treatment of choice

Background. Stress fractures at tracker after computer navigated total knee replacement are rare. Periprosthetic fracture after Minimally Invasive Plate Osteosynthesis (MIPO) of stress fracture through femoral tracker is unique in orthopaedic literature. We are reporting this unique presentation of periprosthetic fractures after MIPO for stress fracture involving femoral pin site track in computer assisted total knee arthroplasty, treated by reconstruction nail (PFNA). Methods. A 75-year old female, who had computer navigated right total knee replacement, was admitted 6 weeks later with increasing pain over distal thigh for 3 weeks without trauma. Prior to onset of pain, she achieved a range of movements of 0–105 degrees. Perioperative radiographs did not suggest obvious osteoporosis, pre-existent benign or malignant lesion, or fracture. Radiographs demonstrated transverse fracture of distal third of femur through pin site track. We fixed the fracture with 11-hole combihole locking plate by MIPO technique. Eight weeks later, she was readmitted with periprosthetic fracture through screw hole at the tip of MIPO Plate and treated by Reconstruction Nail (PFNA), removal of locking screws and refixation of intermediate segment with unicortical locking screws. Then she was protected with plaster cylinder for 4 weeks and hinged brace for 2 months. Results. Retrograde nail for navigation pin site stress fracture entails intraarticular approach with attendant risks including scatches to prosthesis and joint infection. So we opted to fix by MIPO technique. Periprosthetic fracture at the top of MIPO merits fixation with antegrade nail in conjunction with conversion of screws in the proximal part of the plate to unicortical locking screws. Overlap of at least 3cms offers biomechanical superiority. She made an uneventful recovery and was started on osteoporosis treatment, pending DEXA scan. Conclusion. Reconstruction Nail (PFNA), refixation of intermediate segment with unicortical locking screws constitutes a logical management option for the unique periprosthetic fracture after MIPO of stress fracture involving femoral pin site track in computer assisted total knee replacement

1. Stress fractures of the femoral neck in twenty-five patients are described. 2. Two distinct radiological types, compression fractures and transverse fractures, are described. A clinical distinction cannot be made in the early stages. 3. The importance of the early differential diagnosis between the two types is emphasised because the transverse stress fracture of the femoral neck will become displaced. 4. The morbidity after a displaced transverse fracture of the femoral neck can be severe

Aims

Posterior column plating through the single anterior approach reduces the morbidity in acetabular fractures that require stabilization of both the columns. The aim of this study is to assess the effectiveness of posterior column plating through the anterior intrapelvic approach (AIP) in the management of acetabular fractures.

The February 2023 Trauma Roundup³⁶⁰ looks at: Masquelet versus bone transport in infected nonunion of tibia; Hyperbaric Oxygen for Lower Limb Trauma (HOLLT): an international multicentre randomized clinical trial; Is the T-shaped acetabular fracture really a “T”?; What causes cut-out of proximal femur nail anti-rotation device in intertrochanteric fractures?; Is the common femoral artery at risk with percutaneous fragility pelvis fixation?; Anterior pelvic ring pattern predicts displacement in lateral compression fractures; Differences in age-related characteristics among elderly patients with hip fractures.

Despite being one of the most common injuries around the elbow, the optimal treatment of olecranon fractures is far from established and stimulates debate among both general orthopaedic trauma surgeons and upper limb specialists. It is almost universally accepted that stable non-displaced fractures can be safely treated nonoperatively with minimal specialist input. Internal fixation is recommended for the vast majority of displaced fractures, with a range of techniques and implants to choose from. However, there is concern regarding the complication rates, largely related to symptomatic metalwork resulting in high rates of implant removal. As the number of elderly patients sustaining these injuries increases, we are becoming more aware of the issues associated with fixation in osteoporotic bone and the often fragile soft-tissue envelope in this group. Given this, there is evidence to support an increasing role for nonoperative management in this high-risk demographic group, even in those presenting with displaced and/or multifragmentary fracture patterns. This review summarizes the available literature to date, focusing predominantly on the management techniques and available implants for stable fractures of the olecranon. It also offers some insights into the potential avenues for future research, in the hope of addressing some of the pertinent questions that remain unanswered.

Cite this article: Bone Joint J 2023;105-B(2):112–123.

Aims: To investigate the clinical importance of the fracture of lumbar vertebral transverse processes and to þnd out if any correlations exists between the side and the level of the transverse processes fractures and speciþc intraabdominal organ injuries. Methods: 106 patients, sustained different kinds of trauma between January 2000 and January 2001, were included in the study. All patients were operated for intra abdominal causes. Of these 62 (%58) had one or more fractured lumbar transverse processes documented (group I) and remaining 44 had not (group II). Age, gender, additional skeletal and intra abdominal injuries, ISS, laboratory tests results at presentation, transfusion needs and the end results were compared using SPSS 10,0 package. Results: Patients with transverse process fractures were older (38 versus 27, p=0,001). Trauma causes, ISS, additional systemic traumas, skeletal traumas were not different between groups (p values are; 0,148, 0,125, 0,423, 0,673 respectively). However, hemoglobin levels, intra abdominal organ injuries, total hospital stay and end results were signiþcantly different in group I (p= 0,005, 0,042, 0,002 and 0,012). Left sided fractures were well correlated with the spleen, and right sided fractures were similarly correlated with the presence of hepatic injuries. Conclusions: Although lumbar transverse process fractures do not directly relate with vertebral stability, the presence of such a fracture should alert physicians. Especially in multiply injured patients, lumbar vertebra transverse process fracture predisposes more serious intra or retroperitoneal organ injuries

Background: Reverse obliquity and transverse fractures of the proximal femur represent a distinct fracture pattern in which the mechanical forces displace the femur medially thus increasing the risk of fixation failure. There is a paucity of published literature in this area of trauma. This study constitutes the largest series of such fractures. Methods: Using the hip fracture registry at this institution 101 reverse obliquity and transverse fracture patterns were identified from 3336 consecutive hip fractures. All surviving patients were followed up for 1 year. Results: Of 100 patients treated operatively, 59 were treated with 1350 sliding hip screws (SHS), 22 were treated with 1350 sliding hip screw devices designed to resist medialization (3 sliding hip screws with trochanteric plate and 19 Medoff plates), and 19 were treated with intramedullary sliding hip screw devices (1 short Gamma nail, 9 long Gamma nails, 6 Reconstruction nails, 6 long Targon nails, 1 short Targon nail). The SHS had 4 failures (6.8%), and the intramedullary devices one failure (5.3%). Those extramedullary devices augmented to prevent medialization had higher failure rates (1 of 3 SHS with trochanteric plate and 3 of 19 Medoff plates), with combined failure rate of 15.8%. Conclusion: The 1350 SHS and the intramedullary devices had similar failure rates of 6.8% and 5.2% respectively. Those extramedullary devices designed to prevent medialization had higher failure rates (combined failure rate of 4/22 or 18%). This is similar to the high failure rate in 950 devices reported elsewhere. This suggests that extramedullary devices attempting to combat the difficult biomechanics of these fractures are unsuccessful. Better results can be obtained by using the standard 1350 SHS or with intramedullary sliding hip screw devices

Using an osteotomy of the olecranon as a model of a transverse fracture in 22 cadaver elbows we determined the ability of three different types of suture and stainless steel wire to maintain reduction when using a tension-band technique to stabilise the bone. Physiological cyclical loading simulating passive elbow movement (15 N) and using the arms to push up from a chair (450 N) were applied using an Instron materials testing machine whilst monitoring the osteotomy site with a video extensometer. Each osteotomy was repaired by one of four materials, namely, Stainless Steel Wire (7), No 2 Ethibond (3), No 5 Ethibond (5), or No 2 FiberWire (7). There were no failures (movement of > 2 mm) with stainless steel wire or FiberWire and no significant difference in the movements measured across the site of the osteotomy (p = 0.99). The No. 2 Ethibond failed at 450 N and two of the five of No. 5 Ethibond sutures had a separation of > 2 mm at 450 N. FiberWire as the tension band in this model held the reduction as effectively as stainless steel wire and may reduce the incidence of discomfort from the hardware. On the basis of our findings we suggest that a clinical trial should be undertaken

Objectives. Diabetes mellitus (DM) is known to impair fracture healing. Increasing evidence suggests that some microRNA (miRNA) is involved in the pathophysiology of diabetes and its complications. We hypothesized that the functions of miRNA and changes to their patterns of expression may be implicated in the pathogenesis of impaired fracture healing in DM. Methods. Closed transverse fractures were created in the femurs of 116 rats, with half assigned to the DM group and half assigned to the control group. Rats with DM were induced by a single intraperitoneal injection of streptozotocin. At post-fracture days five, seven, 11, 14, 21, and 28, miRNA was extracted from the newly generated tissue at the fracture site. Microarray analysis was performed with miRNA samples from each group on post-fracture days five and 11. For further analysis, real-time polymerase chain reaction (PCR) analysis was performed at each timepoint. Results. Microarray analysis showed that there were 14 miRNAs at day five and 17 miRNAs at day 11, with a greater than twofold change in the DM group compared with the control group. Among these types of miRNA, five were selected based on a comparative and extended literature review. Real-time PCR analysis revealed that five types of miRNA (miR-140-3p, miR-140-5p, miR-181a-1-3p, miR-210-3p, and miR-222-3p) were differentially expressed with changing patterns of expression during fracture healing in diabetic rats compared with controls. Conclusions. Our findings provide information to further understand the pathology of impaired fracture healing in a diabetic rat model. These results may allow the potential development of molecular therapy using miRNA for the treatment of impaired fracture healing in patients with DM. Cite this article: S. Takahara, S. Y. Lee, T. Iwakura, K. Oe, T. Fukui, E. Okumachi, T. Waki, M. Arakura, Y. Sakai, K. Nishida, R. Kuroda, T. Niikura. Altered expression of microRNA during fracture healing in diabetic rats. Bone Joint Res 2018;7:139–147. DOI: 10.1302/2046-3758.72.BJR-2017-0082.R1

Aims

The aim of this study was to report the patterns of symptoms and insufficiency fractures in patients with tumour-induced osteomalacia (TIO) to allow the early diagnosis of this rare condition.

Introduction: Traditionally the fixation of choice as recommended by the AO ASIF group for transverse fractures of the Olecranon and the Patella is the tension band wiring technique. The concept of tension band wiring is based on the fact that the distractive force applied to one surface of the bone will result in compression on the opposite articular surface. Clinical outcomes of TBW are not equivocal. It is associated with significant morbidity such as non union, failure of fixation, especially in osteoporotic bone and infection which sometimes leads to amputation. Often a second procedure for removal of prominent metal work is required. In our biomechanical study we investigated this concept as we believe that the forces generated by TBW construct do not generate significant compressive forces required for healing of fracture. Materials and Methods: We used 4th generation composite bones (Sawbones. ®. , Malmoe, Sweden.). These bone analogues have been validated to closely simulate human bone characteristics for fracture toughness, tensile strength, compressive strength, fatigue crack resistance and implant subsidence. The advantage of using 4th generation composite bone model is that it provides uniformity which is not achievable in cadaveric studies. Two different bone models representative of Olecranon and patella were used. Transverse fractures were created in the bones and fixed with TBW technique as described in A.O. manual. Two 0.062-inch Kirschner wires and figure of eight configuration of 18G Stainless steel wire with single knot technique was used. Micro motion transducers (DVRT: MicroStrain, Williston, Vermont) with an accuracy of ± 1μm were placed across the fracture site both anteriorly and posteriorly. Continuous information regarding fracture distraction and compression, as determined by the transducers was recorded from both sites simultaneously during the experiment. The tension band wire construct was loaded up to a maximum force of 4000 Newtons for patella and 500 for the olecranon. The fractures were subjected to cyclic loading at 1Hz using a servo hydraulic materials-testing system (model 8500; Instron, Canton, Massachusetts). The results were analysed on a computer and statistical analysis performed. Results: During the application of cyclical loading, we noted a gap at the articular surface ranging from 1.1± 0.4mm and 2.1± 0.6mm for Olecranon and patella constructs respectively. During most of the duration of the experiment no transducer displacements were recorded at the articular surface. Conclusion: The concept that distractive forces at one end could be converted to compression at the other end through the TBW does not hold true in our biomechanical study. A simpler construct may suffice for fixation of patellar and Olecranon fractures which can reduce the complications associated with TBW fixation

Introduction: Bilateral and transverse fractures of the first two sacral vertebrae with intrapelvic intrusion of the lumbo-sacral spine are very rare injuries. In most cases the lesion occurs after a fall from great height in a kyphotic position when landing. Today’s CT-scans in these mostly polytraumatized patients enable a clear diagnosis. In contrast conventional radiographs have a high risk to ignore these fractures. Operative treatment requires proper reduction and secure fixation which so far is not unrestricted possible using recommended techniques. For reduction lumbo-sacral distraction followed by lordotic extension is essential but difficult to obtain. Therefore we modified the lumbo-pelvic instrumentation to facilitate these requirements. Methods: In the last four years we treated three female patients (aged 27–68 years) as follows: Variable axis screws (VAS – Synthes®) were inserted in the L4 and L5 pedicles and connected with two connecting rods. An additional variable axis screw was inserted in each posterior iliac spine. These both screws were connected with a transverse connecting rod situated over the transverse fracture line. This rod was connected with the two upright rods using a rod-to-rod connector and forming a hinged joint. Due to the not tightened nut of the pedicle screws at that time it was possible to spread the lumbo-sacral fracture line. After tightening of the lumbar screws the upper part of the body was slightly elevated resulting in a lordotic extension in the hinged joint. Subsequently the hinged joint was locked (Video). Results: Postoperative CT scans revealed anatomic reduction and properly inserted implants in all cases. Follow-up was uneventful but a heparin related thrombopenia in one patient. Two patients were mobilized under full weight bearing within 4 and 10 days, respectively. In one cases this was not possible because of relevant foot fractures. Neurological deficits completely resolved in one patient within fourteen days and markedly diminished in another patient within months (persistent neuralgia). In one patient no neurological deficit existed. In all cases a complete hardware removal was done in 8 to 11 months. Conclusions: The presented procedure is suitable for the so-called jumper’s fractures and results in anatomic reduction of the displaced fractures and a secure stabilization. The described hinged joint offers effective lordotic extension which is the key point for reduction. Thus this configuration is a reduction as well a fixation device. Full weight bearing in an erect posture is immediately possible and clearly shorten the rehabilitation period

For the management of displaced patellar fractures, surgical fixation using cannulated screws along with anterior tension band wiring is getting popular. Clinical and biomechanical studies have reported that using cannulated screws and a wire instead of the modified tension band with Kirschner wires improves the stability of fractured patellae. However, the biomechanical effect of screw proximity on the fixed construction remains unclear. The aim of this study was to evaluate the mechanical behaviors of the fractured patella fixed with two cannulated screws and tension band at different depths of the patella using finite element method. A patella model with simple transverse fracture [AO 34-C1] was developed; the surgical fixation consisted of two 4.0-mm parallel partial-threaded cannulated screws with a figure-of-eight anterior tension band wiring using a 1.25-mm stainless steel cable. Two different locations, including the screws 5-mm and 10-mm away from the leading edge of the patella, were used. A tension force of 850 N was applied on the patellar apexes at two loading angles (45° and 0° [parallel] to the long axis) to simulate different loading conditions while knee ambulation. The proximal side (base) of the patella was fixed, and the inferior articular surface was defined as a compression-only support in ANSYS to simulate the support from distal femur condyles. Compression-only support enables the articular surfaces of the present patella to only bear compression and no tension forces. Under different loading conditions, the fixed fractured patella yielded higher stability during 0° loading of tension force than during 45° loading. When the screws were parallel placed at the depth of 5 mm away from the patellar surface, the deformation of patellar fragment and maximum gap opening at the fracture site were smaller than those obtained by screws placed at the depth of 10 mm away from the patellar surface. Compared to the superficial screw placement, the deeper placement (10 mm) increased the maximum gap opening at the fracture site by 1.56 times under 45° loading, and 1.58 times under 0° loading. The load on the tension band wire of the 10-mm screw placement was 3.12 times (from 230 to 717 N) higher than that of the 5-mm placement. Under the wire, the contact pressure on the patellar surface was higher with the 10-mm screw placement than the 5-mm screw placement. The peak bone contact pressures with the 10-mm placement were 7.7 times (99.5 to 764 MPa) higher. This is the first numerical study to examine the biomechanical effects of different screw locations on the fixation of a fractured patella using screws and tension band. Based on a higher stability and lower cable tension obtained by the superficial screws placement, the authors recommended the superficial screw placement (5 mm below the leading edge of the patella) rather than the deep screws while fixing the transverse patellar fracture with cannulated screws and cable

The Unified Classification System (UCS), or Vancouver system, is a validated and widely used classification system to guide the management of periprosthetic femoral fractures. It suggests that well-fixed stems (type B1) can be treated with fixation but that loose stems (types B2 and B3) should be revised. Determining whether a stem is loose can be difficult and some authors have questioned how to apply this classification system to polished taper slip stems which are, by definition, loose within their cement mantle. Recent evidence has challenged the common perception that revision surgery is preferable to fixation surgery for UCS-B periprosthetic fractures around cemented polished taper slip stems. Indications for fixation include an anatomically reducible fracture and cement mantle, a well-fixed femoral bone-cement interface, and a well-functioning acetabular component. However, not all type B fractures can or should be managed with fixation due to the risk of early failure. This annotation details specific fracture patterns that should not be managed with fixation alone.

Cite this article: Bone Joint J 2023;105-B(5):481–486.

Aims

There is ambiguity surrounding the degree of scaphoid union required to safely allow mobilization following scaphoid waist fracture. Premature mobilization could lead to refracture, but late mobilization may cause stiffness and delay return to normal function. This study aims to explore the risk of refracture at different stages of scaphoid waist fracture union in three common fracture patterns, using a novel finite element method.

Aims

The objectives of this study were to investigate the patient characteristics and mortality of Vancouver type B periprosthetic femoral fractures (PFF) subgroups divided into two groups according to femoral component stability and to compare postoperative clinical outcomes according to treatment in Vancouver type B2 and B3 fractures.

Aims

The aim of this retrospective cohort study was to assess and investigate the safety and efficacy of using a distal tibial osteotomy compared to proximal osteotomy for limb lengthening in children.

Purpose. Knowing the morphology of any fracture, including scaphoid fractures, is important in order to determine the fracture stability and the appropriate fixation technique. Scaphoid fractures are classified according to their radiographic appearance, and simple transverse waist fractures are considered the most common. There is no description in the literature of the 3-dimensional morphology of scaphoid fractures. Our hypothesis was that most scaphoid fractures are not perpendicular to its long axis, i.e. they are not simple transverse fractures. Methods. A 3-dimensional analysis was performed of CT scans of acute scaphoid fractures, conducted at two medical centres during a period of 6 years. A total of 124 scans were analysed (Amira Dev 5.3, Visage Imaging Inc). Thirty of the fractures were displaced and virtually reduced. Anatomical landmarks were marked on the distal radius articular surface in order to orient the scaphoid in the wrist. Shape analysis of the scaphoids and a calculation of the best fitted planes to the fractures were carried out implementing principal component analysis. The angles between the scaphoid's first principal axis to the fracture plane, articular plane and to the palmar-dorsal direction were measured. The fractures were analysed both for location (proximal, waist and distal) and for displacement. Results. There were 86 fractures of the waist (76 percent), 13 of the distal third and 25 of the proximal third. The average angle between the first principal axis of the scaphoid and the fracture plane was 52.6 degrees (SD 17) for all fractures, 55.6 degrees (SD 17.2) for the waist fractures, both differing significantly from a right angle (p<0.001). The majority of fractures were found to be horizontal oblique. We found no difference between the angles of the waist fractures which were displaced and those that were not displaced. In contrast, a significant difference was found between the displaced and non-displaced fractures when evaluating the orientation of the scaphoid long axis in relation to the articular plane (139.8 degrees with reduction versus 148.2 without; p=0.036). Conclusions. Most waist fractures were found to be horizontal oblique in relation to the long axis of the scaphoid and not transverse. Although the fracture angle could not explain displacement of the fracture, we found that the orientation of the scaphoid's long axis in relation to the radial articular surface was correlated with fracture displacement. According to these findings, fixation of all fractures along the long axis of the scaphoid should not be the optimal mode of fixation. Optimal fixation of acute scaphoid fractures may call for better analysis of each fracture configuration and the fixation should be guided by this analysis

Purpose. Knowing the morphology of any fracture, including scaphoid fractures, is important in order to determine the fracture stability and the appropriate fixation technique. Scaphoid fractures are classified according to their radiographic appearance, and simple transverse waist fractures are considered the most common. There is no description in the literature of the 3-dimensional morphology of scaphoid fractures. Our hypothesis was that most scaphoid fractures are not perpendicular to its long axis, i.e. they are not simple transverse fractures. Methods. A 3-dimensional analysis was performed of CT scans of acute scaphoid fractures, conducted at two medical centers during a period of 6 years. A total of 124 scans were analysed (Amira Dev 5.3, Visage Imaging Inc). Thirty of the fractures were displaced and virtually reduced. Anatomical landmarks were marked on the distal radius articular surface in order to orient the scaphoid in the wrist. Shape analysis of the scaphoids and a calculation of the best fitted planes to the fractures were carried out implementing principal component analysis. The angles between the scaphoid's first principal axis to the fracture plane, articular plane and to the palmar-dorsal direction were measured. The fractures were analysed both for location (proximal, waist and distal) and for displacement. Results. There were 86 fractures of the waist (76 percent), 13 of the distal third and 25 of the proximal third. The average angle between the first principal axis of the scaphoid and the fracture plane was 52.6 degrees (SD 17) for all fractures, 55.6 degrees (SD 17.2) for the waist fractures, both differing significantly from a right angle (p<0.001). The majority of fractures were found to be horizontal oblique. We found no difference between the angles of the waist fractures which were displaced and those that were not displaced. In contrast, a significant difference was found between the displaced and non-displaced fractures when evaluating the orientation of the scaphoid long axis in relation to the articular plane (139.8 degrees with reduction versus 148.2 without; p=0.036). Conclusions. Most waist fractures were found to be horizontal oblique in relation to the long axis of the scaphoid and not transverse. Although the fracture angle could not explain displacement of the fracture, we found that the orientation of the scaphoid's long axis in relation to the radial articular surface was correlated with fracture displacement. According to these findings, fixation of all fractures along the long axis of the scaphoid should not be the optimal mode of fixation. Optimal fixation of acute scaphoid fractures may call for better analysis of each fracture configuration and the fixation should be guided by this analysis

Weber A fractures are a sub-group of ankle fractures parallel or distal to the joint line, below the level of the syndesmosis. Most stable Weber A fractures are managed conservatively with no significant difference in outcome vs. surgical intervention. 1,2. In an effort to ensure staff time was being used as efficiently as possible, a consultant-led virtual fracture clinic (VFC) was introduced to manage Weber A fractures. Patients not requiring immediate surgery were reviewed remotely and, wherever possible, were ‘virtually discharged’ to a nurse-led telephone line. Those with diagnostic uncertainty, unusual features or delayed recovery received a face to face review from a nurse or surgeon. To examine how patients were allocated under this protocol, along with overall patient satisfaction and functional outcome. An audit of satisfaction and outcome was performed of all patients who presented with a Weber A fracture to the ED between October 2011 and October 2012. The minimum follow-up period was two years. A satisfaction and patient reported outcome (5-level-likert-scale, EQ-5D, MOXFQ) measure was conducted via telephone. 3,4. After exclusions, 79 patients were left, of which 63 were successfully contacted (80%). Of the 79 patients included, 33 (42%) required early face-to-face review while 46 (58%) were discharged with advice following discussion at the VFC. Of the 63 successfully contacted, receipt of the information leaflet was recalled by 61 (97%) and 54 (86%) were satisfied with the information they had received. There was no difference in patient satisfaction regarding recovery (p=0.079) or treatment information (p=0.236) provided between avulsion and transverse fractures or in functional outcome according to MOXFQ (p=0.626) or EQ-Vas (p=0.915) scores. Patient satisfaction can remain high without face-to-face consultations following injury. This was demonstrated by the high satisfaction with recovery (83%) and with information provided (86%) and is consistent with current published literature and similar to what would have been achieved with traditional fracture clinic review. 5. The new protocol reduces unnecessary hospital attendances for patients and reduces the burden of unnecessary review in orthopaedic departments. Only 15% of patients required review at a traditional fracture clinic and 27% at a nurse-led clinic, freeing resources for more complex cases

Aims

There are concerns regarding nail/medullary canal mismatch and initial stability after cephalomedullary nailing in unstable pertrochanteric fractures. This study aimed to investigate the effect of an additional anteroposterior blocking screw on fixation stability in unstable pertrochanteric fracture models with a nail/medullary canal mismatch after short cephalomedullary nail (CMN) fixation.

Aims

Clinical management of open fractures is challenging and frequently requires complex reconstruction procedures. The Gustilo-Anderson classification lacks uniform interpretation, has poor interobserver reliability, and fails to account for injuries to musculotendinous units and bone. The Ganga Hospital Open Injury Severity Score (GHOISS) was designed to address these concerns. The major aim of this review was to ascertain the evidence available on accuracy of the GHOISS in predicting successful limb salvage in patients with mangled limbs.

The retrograde Marchetti-Vicenzi humeral nail consists of four or five flexible branches. At one end these branches are fixed into a solid L-shaped cylinder and at the other, they are held together with a locking wire. The nail is inserted in a retrograde way through a cortical window proximal to the olecranon fossa. Once passed the fracture, removing the locking wire allows the branches to spread in the metaphysis providing proximal stability. Distal locking is achieved through screw fixation. The Marchetti-Vicenzi nail presents several theoretical advantages. Its flexible branches facilitate nail insertion and might favour fracture healing. Distal locking is performed under direct vision from posterior to anterior and additional proximal locking is not required, preventing iatrogenic neurovascular damage. Distal locking avoids nail migration and retrograde nail insertion spares the rotator cuff. Early mobilisation is often possible. This leads to an equally good elbow function, but with a better shoulder function compared to antegrade nailing. On the other hand, limited rotational stability, especially in transverse fractures, can cause non-union and hardware failure. In the initial design, the bulky L-shaped end made a large supracondylar insertion and removal window mandatory, increasing the risk of fracture in this area. In the later version, the angle of the L-shaped cylinder has therefore been modified. In our opinion, the use of the Marchetti-Vicenzi nail is not advisable in comminuted or transverse humeral fractures, in fractures extending in the distal third or in patients (young ladies) with a narrow medullary canal. Nail removal should only be considered if absolutely necessary

As the incidence of total hip arthroplasty (THA) rises, an increasing prevalence of peri-prosthetic femur fractures has been reported. This is likely due to the growing population with arthroplasties, increasing patient survival and a more active life-style following arthroplasty. It is the 3rd most common reason for THA reoperation (9.5%) and 5th most common reason for revision (5% with fracture risk after primary THA reported at 0.4%-1.1% and after revision at 2.1%-4%). High quality radiographs are usually sufficient to classify the fracture and plan treatment. Important issues in treatment include stem fixation status and fracture location relative to the stem. Additional comorbidities will also influence treatment choices, of which the most critical is the presence of infection and the quality of bone stock. The most commonly studied, and reported classification system is the Vancouver. Type A are peri-trochanteric fractures with AL at the lesser and AG at the greater trochanter. B fractures are those around the stem with B1 fractures having a well-fixed stem, B2 a loose stem with adequate bone stock, and B3 representing loose stem and inadequate bone stock. C fractures are distal to the stem. Type A) Trochanteric Fractures: These are usually associated with lysis. Displaced fractures can be managed adequately with cerclage fixation and cancellous allograft to fill osteolytic defects. Undisplaced fractures usually heal well with symptomatic treatment. Type B) Fractures Around the Stem: The B1 type has a well-fixed component and is usually treated with extramedullary fixation plus graft. Contemporary plates have been designed specifically for these fractures. Strut allograft may be used to provide a more rigid construct. Spiral and long oblique fractures can be cerclaged while short oblique or transverse fractures require fixation anterior and lateral with cable plates and cortical strut grafts. Screws can be used distal to the implant, and cables used proximally. The B2 type has a loose prosthesis but otherwise good bone stock. In this setting, the fracture line may be extended on the lateral cortex of the femur as an extended osteotomy to provide easy access for cement removal. These fractures can be managed with an extensively coated stem if rotational stability can be obtained in the distal segment. If rotational stability over a 4 cm scratch interference fit of the stem isn't possible, then a fluted tapered modular stem should be used. Strut allografts improve initial stability. The B3 type has both a loose prosthesis and poor bone stock and in the younger patient restoration of bone stock should be a priority. Bulk femoral grafts may be needed. The elderly or low functional demand patient may be treated with a proximal femoral replacement. Because of soft-tissue deficiencies, a constrained acetabular liner may be needed to prevent instability. Type C) Fractures Distal to the Stem: These usually accompany a stable stem and many fixation devices are available. Locking plates have become most popular and should be secured with cerclage wires proximally around the component with screws distally. Retrograde nails may be employed if there is adequate bone distal to the stem tip and above the fracture

The advent of Elastic Stable Intramedullary Nailing has revolutionised the conservative treatment of long human bone fractures in children (Metaizeau, 1988; Metaizeau et al., 2004). Unfortunately, failures still occur due to excessive bending and fatigue (Linhart et al., 1999; Lascombes et al., 2006), bone refracture or nail failure (Bråten et al., 1993; Weinberg et al., 2003). Ideally, during surgery, nail insertion into the diaphyseal medullary canal should not interrupt or injure cartilage growth; nails should provide an improved rigidity and fracture stabilisation. This study aims at comparing deflections and stiffnesses of nail-bone assemblies: standard cylindrically-shaped nails (MI) vs. new cylindrical nails (MII) with a flattened face across the entire length allowing more inertia and a curved tip allowing better penetration into the cancellous bone of the metaphysis (Figure 1). MII exhibits a section with two parameters: a diameter C providing nail stiffness and a height C' providing practical dimension when both nails are crossed at the isthmus of the diaphysis: C/C' is set to 1.25 for all MII nails. A CT scan of a patient aged 22 years was used to segment a 3D model of a 471mm-long right femur model. The medullary canal diameters at the isthmus are 10.8mm and 11.4mm in the ML and AP direction, respectively. Titanium-made CAD models of MI (Ø=4mm) and MII (flat face: Ø=5mm) were pre-curved to maintain their flat face and carefully placed and positioned according to surgeon's instructions. Both nails were inserted via lateral holes in the distal femur with their extremities either bumping against the cortex or lying in the trabecular bone. Transverse and comminuted fractures were simulated (Figure 1). For each assembly, a Finite Element (FE) tetrahedral mesh was generated (∼100181 nodes and 424398 elements). Grey-scale levels were used to assign heterogeneous material properties to the bone (E=6850 ρ. 1.49. (Morgan et al., 2003)). Two modes of loading were considered: 4-point bending (varus and recurvatum: F. max. =6000N) and internal torsion (M. max. =70kNmm). This led to the simulation of 15 FE models, including a reference intact femur. Results show that in valgus, for the transverse (comminuted) fracture, the mean displacement of the assembly decreased by around 50%: from 15.24mm (27.49mm) to 8.15mm (13.85mm) for MI and MII, respectively, compared to 3.59mm for the intact bone. The assembly stiffness increased by 87% and 99% for transverse and comminuted fracture, respectively (Table 1). Similar trends were found in recurvatum with higher increases in assembly stiffness of 170% and 143% for transverse and comminuted fracture, respectively (Table 1). In torsion, for the transverse (comminuted) fracture, the measured angle of rotation decreased from: 0.43rad (0.66rad) to 0.22rad (0.43rad) for MI and MII, respectively, compared to 0.09rad for the intact bone. This corresponded to an increase of 95% and 55% in assembly stiffness for transverse and comminuted fracture, respectively. In conclusion, using the 5mm-diameter new nails (MII) for the same intramedullar space, during either bending or torsion, assemblies were always stiffer than when using standard cylindrical nails

The patella is an important component of the extensor mechanism of the knee. Patellar fractures need to be fixed if displacement occurs more than 2 mm. Transverse fractures comprise the largest category. Several different techniques for internal fixation have been employed. The aim of this work was to evaluate the results of treatment of transverse patellar fractures with figure of eight wiring through cannulated screws. Twenty patients were included in the study, all suffering from displaced transverse patellar fractures. All were treated by open reduction and internal fixation with figure of eight tension band wire through 4.0 mm cannulated screws. All patients were assessed after 1 month, 3 months and 6 months according to a modified Hospital for special surgery (HSS) knee scoring system. Because varus and valgus knee alignment and stability are not affected by patellar fracture fixation, the ten points assigned to these functions are eliminated, making the highest score ninety points. Excellent results are considered with points from 75 to 90, good from 60 to 74, fair from 50 to 59 and poor with points below 50. The final results of the study showed fourteen patients (70%) had excellent results, five (25%) good result, one (5%) fair result and no patient had a poor result. There was a statistically significant improvement of the patients' score throughout the follow up period. The complications occurred included knee pain in one patient (5%), loss of terminal flexion of knee occurred in three patients (15%), one patient lost 30 degrees, another lost 20 degrees while the last lost 10 degrees. There were no cases with extension lag in this series. Treatment of patellar fractures using figure of eight wiring through cannulated screws is an easy technique which gives good stability leading to good results with a low complication rate

Background. Sub-trochanteric fractures are challenging to treat due to various anatomical and biomechanical factors. High tensile forces contribute to the challenge of fracture reduction. Intramedullary nailing has become the treatment of choice. If anatomical reduction is not achieved, any mal-alignment will predispose to implant failure. Open reduction with cerclage wires can add to construct stability and improve the quality of reduction. There is no consensus or classification to guide surgeons on when to perform open reduction, which is often performed intra-operatively when closed reduction fails often with no planning. This can lead to intraoperative delays as theatre staff would not have prepared the correct equipment necessary for open reduction. Objectives. The purpose of this study was to assess outcomes of closed and open reduction of traumatic sub-trochanteric fractures treated with intramedullary nailing and to propose a new classification system to dictate management. Methods. After a review of current classification systems, a 3-tier classification was proposed (Type 1, 2 and 3). Type 1 indicated a transverse fracture, Type 2 was a spiral fracture with an intact posterior and medial wall and a Type 3 fracture were fractures with no posterior and/or medial walls. Over a two-year period (2013–2015), patients with sub trochanteric fractures were classified into Type 1, 2 or 3 injuries based on radiographic appearances by two senior clinicians. Patients with Type 3 injuries were divided into two groups based on whether they were treated with open or closed reduction. A clinical and radiographic review was performed. The primary outcome measure was the incidence of implant failure, whereas secondary outcome measures were related to fracture reduction. Statistical analysis was performed using GraphPad Prism Version 6 (GraphPad Software Inc. California, USA). Fisher's exact test was used for independent categorical data and Mann–U Whitney for continuous nonparametric data. Statistical significance was set at p<0.05. Results. 75 patients had intramedullary nailing for subtrochanteric fractures over the study period with a mean age of 82.6 years. There were 48 patients who had a Type 3 fracture pattern with a deficient medial and/or posterior wall. Reduction was achieved open with cerclage wires in 42% of patients (n=20 and closed in 58% (n=28). Overall there were a total of 18 (37.5%) major complications. In patients treated with closed reduction, 9 patients suffered mechanical complications (6 distal locking screw failures, 3 lag screw cut outs). There was a significantly increased risk of implant failure in patients treated with closed reduction compared to open reduction (p=0.006). No cases with cerclage wire had implant failure. Open reduction with cerclage wires improved the quality of reduction (p=0.0001) compared with closed reduction. There was no significant increase in operating time in patients treated with cerclage wires (p=0.4334). Conclusions. Open reduction with cerclage wires should be considered in patients with Type 3 sub-trochanteric fractures as it has shown to significantly reduce the risk of implant failure and improve the quality of reduction with no significant increase in operating time

Aims

After failed acetabular fractures, total hip arthroplasty (THA) is a challenging procedure and considered the gold standard treatment. The complexity of the procedure depends on the fracture pattern and the initial fracture management. This study’s primary aim was to evaluate patient-reported outcome measures (PROMs) for patients who underwent delayed uncemented acetabular THA after acetabular fractures. The secondary aims were to assess the radiological outcome and the incidence of the associated complications in those patients.

The radius has a sagittal and coronal bow. Fractures are often treated with volar anterior plating. However, the sagittal bow is often overlooked when plating. This study looks at radial morphology and the effect of plating the proximal radius, with straight plates then contoured plates bowed in the sagittal plane. We report our findings and their effect on forearm rotation. Morphology was investigated using fourteen radii. Attention was made to the proximal shaft of the radius and its sagittal bow, from this 6, 7 and 8 hole plates were contoured to fit this bow. A simple transverse fracture was then made at the apex of this bow. Supination and pronation was then compared when plating with a straight plate and a contoured plate. Ten cadavers had the ulna plating at the same level. The effect on rotation of fractures plated in the distal third shaft was also measured. A significant reduction in rotation was found, when a proximal radius fracture was plated with straight plate compared to a contoured plate: 10.8, 12.8, 21.7 degrees (p<0.05 for 6, 7, 8 hole plates). Forearm rotation was decreased further when a longer plate was used. Ulna or distal shaft plating did not reduce rotation. This study has shown a significant sagittal bow of the proximal shaft of the radius. Plating this with contoured plates in the sagittal plane improves rotation when compared to straight plates. Additional ulna plating is not a source of reduced forearm rotation

Fracture of the acetabulum can lead to degenerative arthritis of the hip, avascular necrosis of the femoral head, or both. Total hip arthroplasty is a common form of surgical treatment when significant joint changes and pain are present. Ten patients with fracture acetabulum were treated in this study using metal on metal total hip arthoplasty. The initial fracture was posterior wall fracture in one patient, posterior column fracture in one patient, transverse fracture in 2 patients, fracture dislocation in 3 patients and fracture posterior wall and column in 3 patients. The indications of arthroplasty were secondry osteoarthritis after internal fixation or after conservative management or collapse of the femoral head. Arthroplasty was done after an average period of 1.8 years (range from 1 to 4 years). After a follow up period ranged from 3 to 7 years with a mean of 4.6 years, the Harris hip score was improved from a mean of 51 (range 20 to 65) to a mean of 92.5 (range 90 to 95). Infection occurred in one case and two stages revision was done. Another case developed loosening of the acetabular component and was revised using cementless cup fixed with screws and bone graft. Metal on metal THR after acetabular fracture are relatively uncomplicated and lead to a good outcome despite the difficulties faced during the procedure

Fractures of the proximal femur at the level of the lesser trochanter (reversed and transverse fracture lines, Evans classification type II, AO classification A3 fractures) are known to have an increased risk of fixation failure. 58 patients with such a fracture were randomised to have the fracture fixed with either an intramedullary nail (220 mm Targon PF nail) or a sliding hip screw (SHS). The mean age of the patients was 82 and 11% were male. All patients were followed up for one year by a research nurse blinded to the treatment groups. Mean length of surgery was 50 minutes for the nail versus 52 minutes for the SHS. There were no differences between groups in the need for blood transfusion. Operative complications tended to be less for the nail group (1/27 versus 5/26). Mean hospital stay was 18 days for the nail group versus 29 days for those treated with the SHS. The only fracture healing complications were one case of cut-out in the SHS group and two cut-outs in the nail group, two of which required revision surgery. During follow-up those patients treated with the nail reported a tendency to lower pain scores than those treated with the SHS (p=0.04 at two months). This difference persisted even at one year from injury. Mortality and regain of mobility was similar between groups. These results indicate that for these difficult fractures types both types of fixation produce comparable outcomes

Purpose: To describe the diagnostic planning and treatment modalities of six patients with this rarest of sacral fractures. Due to the low incidence of these injuries, there is no literature evidence concerning their management. Materials and Methods: Six patients with a transverse fracture of the sacrum with anterior displacement. All patients were admitted with bowel and bladder dysfunction, perineal anesthesia, sensory and motor deficits at the lower extremities. Prompt diagnosis of the sacral fracture was obtained in five of the six patients. Results: Operative treatment including extensive lumbosacral laminectomies, spine instrumentation and fusion was performed in all cases. Neurological recovery was almost complete in one patient, partial in 4 patients and absent in one patient. Conclusions: A more favorable clinical outcome can be achieved when operative treatment is implemented using lumbosacral decompression by laminectomy, dural repair and posterolateral instrumented fusion with bone grafting. Although reduction of the fracture was not ideal in many of these patients, long term clinical and radiographic follow – up as well as neurological improvement were rewarding

The results of resurfacing or not resurfacing the articular cartilage of the patella were reviewed in 71 knees--47 with rheumatoid arthritis and 24 with osteoarthritis--which had been replaced with the ICLH prosthesis. Two rheumatoid and osteoporotic patellae developed transverse fractures with separation and were excluded from the review. The results showed that resurfacing the patella greatly reduced peripatellar pain with no counter-balancing disadvantage

Summary Statement. The Dkk3-derived cells represent a branch of the periosteal mesenchymal lineage that produces fibrocartilage as well as regenerating the periosteal structures. Introduction. Mesenchymal progenitor cells are capable of generating a wide variety of mature cells that constitute the connective tissue system. Our Laboratory has been developing SMAA GFP reporter mice to prove to be an effective tool for identifying these cells prior to the expression of markers of differentiation characteristic of bone, fat, muscular blood vessels or fibrocartilage. Dkk3 was chosen as a candidate reporter because microarray of SMAA-sorted cells culture indicated high expression of this non-canonical anti-Wnt factor, which was not anticipated in a culture with strong osteogenic potential. Material and Methods. Fracture healing process was evaluated in 12 week old male mice at 3, 5, 7, 14, 21 and 28days post fracture. A 3 color reporter mouse was generated by crossing SMAA-GFPcherry × Col3.6GFPcyan × Dkk3-eGFP and subjected to tibial fracture. A closed transverse fracture was performed by Einhorn device under isoflurane anesthesia after insertion of intramedullary pinning. Longitudinal 5 mm non-calcified cryosections were stabilised with Cryofilm tape. Results. Three days post fracture, the proliferating SMAA-red cells were also beginning to express either Dkk3 or Col3.6. By day 5 the two populations had diverged with the Dkk3 cells being on the outer surface of the developing callus while the Col3.6 cells were forming bone at the base of the callus. By day 7 when the callus is filled with cartilage, Dkk3 is active in cells that are in transition from elongated cells on the external surface of the callus to fibrocartilagenous cells that now express low levels of Col3.6. The zone of cells that express Dkk3 appear to block the passage of the surrounding vasculature into the underlying cartilage and does not deposit fibronectin. By day 14–21 when the cartilage core is resorbed, the only remaining Dkk3 is located in the newly formed periosteum external to the active endocortical bone forming activity associated with the inward remodeling of the outer cortical shell. Discussion. We interpret these findings that Dkk3 marks a non-osteogenic limb of the SMAA progenitor population that within the fracture partitions the osteogenic signals away from the surrounding skeletal muscle and the underlying differentiating fibrocartilage. It is a progenitor to cells that form fibrocartilage in the fracture zone as well as the tenascin C positive cells that populate the fibrous zone of the periosteum, and it resides in the cambial zone of the periosteum. Knowing the biological and molecular function of these cells should lead to a fuller appreciation of the pro- and anti-osteogenic factors that regulate skeletal repair

Fractures of the proximal femur at the level of the lesser trochanter (reversed and transverse fracture lines, Evans classification type II, AO classification 31. A3 fractures) are known to have an increased risk of fixation failure. 53 patients with such a fracture were randomised to have the fracture fixed with either an intramedullary nail (220 mm Targon Proximal Femoral nail) or a Sliding Hip Screw (SHS). The mean age of the patients was 82 and 11% were male. All patients were followed up for one year by a research nurse blinded to the treatment groups. Mean length of surgery was 51 minutes for the nail versus 53 minutes for the SHS. There were no differences between groups in the need for blood transfusion. Operative complications tended to be less for the nail group (1/27 versus 5/26). Mean hospital stay was 17 days for the nail group versus 29 days for those treated with the SHS (p< 0.0001). The only fracture healing complications were one case of cut-out in each group requiring revision surgery. During follow-up those patient treated with the nail reported significantly lower pain scores than those treated with the SHS (p=0.08). This difference persisted even at one year from injury. In addition there was a tendency to a better regain of mobility in the first nine months from injury for those treated with the nail. These results indicate that for these difficult fractures types an intramedullary nails produces superior results to the Sliding Hip Screw