Introduction

Partial meniscectomy, a surgical treatment for meniscal lesions, allows athletes to return to sporting activities within two weeks. However, this increases knee joint shear stress, which is reported to cause osteoarthritis. The volumes and locations of partial meniscectomy that would result in a substantial increase in knee joint stress is not known. This information could inform surgeons when a meniscus reconstruction is required.

Introduction

Osteoarthritis commonly affects the first metatarsophalangeal joint. Stress across this joint has been postulated to increase the incidence of osteoarthritis. Certain foot structures have been associated with a higher incidence of osteoarthritis of the big toe. Utilizing finite elemental analysis, bone stress across the first metatarsophalangeal joint was calculated during mid stance phase of gait and compared in different foot structures.

14.1% of men & 22.8% of women over 45 years show symptoms of osteoarthritis OA of the knee [1]. Knee OA is usually associated with lower limb malalignment [2]; 50 of varus results in 70% −90% increase in compressive loading of the medial tibio-femoral compartment [3] and OA worsening over 18 months [4]. High Tibial Osteotomy (HTO) enables preservation of bone stock and soft tissue structures and could be an attractive option to younger patients who wish to return to high level activity. However, results of HTOs are unpredictable, which could be due to patient selection or surgical techniques. The long-term aim of this work is to develop a predictive tool to aid the surgeon in the selection of optimal HTO geometry for improved and more consistent surgical outcomes. The first step in achieving our longterm goal was to determine whether stress predictions at the tibio-femoral articulation were sensitive to simulated high tibial osteotomy, using finite element (FE) method.

CT and MRI data of a cadaveric knee were used to create geometrically accurate 3D models of the femur, tibia, fibula, menisci and cartilage and tendon of the knee joint, using the Mimics V12.11 commercially-available software (Materialise, Belgium). The Simulation module was used to register the bones and the soft tissues. The resulting STL files were exported to CATIA V5R18 pre-processor to generate surface meshes and create the corresponding 3D solid and FE models of the osseous and soft tissues from the STL cloud of points.

The Young’s moduli for cortical bone, cancellous bone, cartilages, menisci and ligaments were taken from literature as 17 GPa, 500 MPa, 12 MPa, 60 Mpa and 1.72 MPa respectively [5,6,7]. The Poisson’s ratios for osseous and soft tissues were taken as 0.3 and 0.45, respectively [8]. The nodes between the bones and the corresponding cartilages were merged and surface contact was applied between the cartilages. The distal ends of the tibia and fibula were fixed and a load of 2.1 KN, corresponding to 3 x body weight, was applied perpendicularly to the proximal end of the femur. Results of finite element analyses show a reduction of 67 % in principal stresses in the knee joint following an open wedge HTO surgery simulating 100 varus correction.

FE analysis results of this study show that HTO reduces stresses in specific regions of the knee, which are associated with OA progression [4]. Our future works include corroborating our results with controlled cadaveric experiments and implementing optimization techniques to predict optimum HTO geometries for patient-specific FE models.

Cemented total hip replacements (THR) are widely used and are still recognized as the gold standard by which all other methods of hip replacements are compared. [1]. Long-term results of cemented total hip replacements show that the revision rate due to aseptic loosening could be as high as 75.4% [2]. Moreover, high stresses developed in the cement mantle of reconstructed hips can lead to premature failure of the constructs [3]. Surgical fixation techniques vary considerably [4]. The aim of this study was to investigate the performances of different surgical fixation techniques of hip implants for patients with different body mass indices, bone morphology and bone quality, using finite element (FE) methods.

Anatomically correct reconstructed hemi-pelves were created, using CT-Scan data of the Visible Human Data set, downloaded to Mimics V8.1 software, where poly-lines of cancellous and cortical bones were created, and exported to I-Deas 11.0 FE package, where the econstructed hemi-pelvis was simulated. Accurate 3D model of the hemi-pelvis was scaled up and down to create hemi-pelves of acetabular sizes of the following diameters: 46 mm, 52 mm, and 58 mm. Following sensitivity analyses, element sizes ranging from 1–3 mm were used. Material properties of the bones, implants and cement were taken from literature [5–7]. Bones of poor quality were simulated by a reduction in the elastic modulii of the cortical bone by 50%, the cancellous bone by 10 % and the subchondral bone by 50% [5]. The nodes at the sacro-iliac joint areas and the pubic support areas were fixed. A compressive force of 3 times body weight was simulated at the hip joint. The nodes between the cancellous and subchondral bones were merged. Contact elements were used at the subchondral bone and cement mantle interface and between the femoral head implant and acetabular component. Dynamic in vitro tests, simulating forces acting on a hip joint during a gait cycle, were carried out on reconstructed synthetic bones, positioned on an Instron 8874 hydraulic machine, to verify the FE models.

The volume of cement stressed at different levels in groups of 0–1 MPa, 1–2 MPa and up to 11 and above MPa were calculated. Results of FE analyses showed that

an increase in the body mass index from 20 to 30 generated an increase in the tensile stress level in the cement mantle;

Results of in-vitro tests show that an increase in the cement mantle thickness improved fixation, corroborating with the FE results.

Performances of fixation techniques depend on the patient’s bone mass index, bone quality, bone morphology.

Aims: Pressure sores are potentially serious complications caused by capillary closure due to extended periods of immobilization such as during surgery. Jellypads are available to reduce this risk but are costly and have been shown to harbour bacteria, thereby posing as an infective risk in implant surgery. The aim of this study is to investigate the potential use of more cost effective, clean, disposable product, without compromising on efficacy. Methods: Currently marketed (jellypad) and novel (bubblewrap) pressure relief products were used in this study to compare pressures generated when a subject sat on the different products. Varying diameter bubblewrap in differing layer structure was used to assess whether (a) the novel material offered better pressure relief and if so, (b) which configuration provided the best pressure dispersion. Results: Our results show that bubblewrap seems to offer better relief of pressure than jellypad. Two to four layers of 10 mm diameter bubblewrap used in opposite directions was the optimum configuration. Conclusion: Based on our investigations, we believe that bubblewrap is a better product for the prevention of pressure sores. Bubble-wrap results in lower peak and average pressure values than jellypad. Moreover, bubblewrap is cheap, disposable and is less likely to transmit infections.