Introduction

A new conservative hip stem has been designed to address the complex problem of total hip arthroplasty in the younger population.

Hip resurfacing arthroplasty is emerging as an increasingly popular, conservative option for the treatment of end-stage osteoarthritis in the young and active patient. Despite the encouraging clinical results of hip resurfacing, aseptic loosening and femoral neck fracture remains concerns for the success of this procedure.

This study used finite element analysis (FEA) to analyse the stresses within proximal femoral bone resulting from implantation with a conservative hip prosthesis. FEA is a computational method used to analyse the performance of real-world structures through the development of simplified computational models using essential features.

The aim of this study was to examine the correlation between the orientation of the femoral component of a hip resurfacing prosthesis (using the Birmingham Hip Resurfacing as a model) and outcomes during both walking and stair climbing. The outcomes of interest were stresses in the femoral neck predisposing to fracture, and bone remodelling within the proximal femur.

Multiple three-dimensional finite element models of a resurfaced femur were generated, with stem-shaft angles representing anatomic (135°), valgus (145°), and varus (125°) angulations. Applied loading conditions included normal walking and stair climbing. Bone remodelling was assessed in both the medial and lateral cortices.

Analyses revealed that amongst all orientations, valgus positioning produced the most physiological stress patterns within these regions, thereby encouraging bone growth. Stress concentration was observed in cortical and cancellous bone regions adjacent to the rim of the prosthesis. As one would expect, stair climbing produced consistently higher stress than walking. The highest stress values occurred in the varus-orientated femur during both walking and stair climbing, whilst anatomic angulation resulted in the lowest stress values of all implanted femurs in comparison to the intact femur.

This study has shown through the use of FEA that optimising the stem-shaft angle towards a valgus orientation is recommended when implanting a hip resurfacing arthroplasty. This positioning produces physiological stress patterns within the proximal femur that are conducive to bone growth, thus reducing the risk of femoral neck fracture associated with conservative hip arthroplasty.

Scarf osteotomy is widely used as a surgical treatment for hallux valgus. It is a versatile osteotomy, allowing shortening, depression or medial displacement of the capital fragment but it remains uncertain how stresses within the bone subsequently vary. The aim of this study was to design a computerised model to explore the effect on bone stress of changing the position of bony cuts for a scarf osteotomy.

A computerised image was constructed using finite element analysis. This utilises a mathematical technique to form element equations which represent the effect of applied force to the object appropriate to each finite element. Maximum bone stresses were then measured using different osteotomy variables. The osteotomy variables studied were the length of the longditudinal cut, apex of the distal cut to articular cartilage, resection level of the longditudinal cut and combinations of these variables. A saw bone model was used to test the findings of the study.

The results of this study show that lowering the longditudinal resection level and shortening via the distal cut beyond 6 mm will decrease bone stress. Additionally, raising the longditudinal resection level and shortening via the proximal cut caused an increase in bone stress. A saw bone model confirmed the findings of the study.

In conclusion, our experience is that finite element analysis is a very useful model in studying the bony stresses for a scarf osteotomy and assists in optimising the direction and angle of bony cuts used.

Introduction & Aims: A new femoral component for hip arthroplasty has been designed for a younger patient population. The design makes use of a higher femoral cut, which conserves bone stock, increasing options for future revision surgery. It uses the existing load bearing properties of the proximal femur, and therefore distributes load more evenly. The stem is longer than that of a resurfacing, so will be easier to insert at the correct orientation, minimising failure rates in inexperienced hands. The cross-sectional dimensions have been designed to produce torsional stability. The collar maximises the loading of the calcar, reducing stress resorption. The surface is hydroxyapatite coated and porous, which will produce a long-term biological fixation.

This project assessed the long-term stability of this design at different orientations, by measuring the change in surface strain distribution following its insertion.

Methods: Ten composite bones were coated in a Photoelastic material, positioned at a simplified single leg stance, and loaded at 2.3 KN. The surface strain was measured at one-centimetre intervals down the medial cortex. Then the prostheses were inserted into the bone at 135°, 145° and 125° to the femoral shaft, and the surface strains reread.

Results: The results were compared with an FEA model, and analysed statistically using the Wilcox signed rank test. The prosthesis inserted at 135° produced no significant difference in surface strain distribution compared with the intact bone.

Conclusions: This study suggests this stem design will be stable in the long term following insertion, and there were no areas of excessively high or low strain.

We previously demonstrated that cartilaginous tissue was induced on a reamed acetabular articulation in an ovine hemiarthroplasty model with three different femoral head sizes. At maximum loading during stance phase, the acetabular peak stresses immediately after reaming could reach approximately 80 MPa under direct implant-bone contact with in-vitro measurements.

We aimed to establish finite element (FE) models of the ovine hip hemiarthroplasty which examine stress distribution on the reamed acetabula by three head sizes. We hypothesized that the stress distribution did not differ between different sizes when the joint is congruent and that the peak stresses in the acetabulum immediately after reaming occurred in the dorsal acetabulum.

Three two-dimensional FE models of ovine hip hemi-arthroplasty were built; each comprised a head component, 25, 28, and 32 mm in diameter, and an acetabular component. The acetabular geometry was acquired from an ovine acetabular histological section. The head was moved to partly intersect with the acetabulum representing the reaming procedure and a congruent contact was confirmed. Cortical bone and cancellous bone were modelled as linear elastic, with moduli of 20 and 1.2 GPa, respectively. Variable moduli were also assessed. The finest mesh for each model consisted of over 100,000 four-node quadrilateral elements. Loading conditions were chosen to represent peak hip joint force developed during the stance phase. Stress distribution in the acetabular area in contact with the head was plotted against the articulating arc length.

The results confirmed that the stress distribution between different prosthetic head sizes in a reamed hemiarthroplasty model did not change when the joint was congruent. The peak compressive stresses occurred in the dorsal acetabulum with the 32 mm model being the highest at approximately 69 MPa, the 28 mm model at 63 MPa, and the 25 mm model at 54 MPa. An increase in the cancellous modulus and a decrease in the cortical modulus increased the peak stresses in the dorsal acetabulum.

This presents an indicative study into the effect of prosthetic femoral head sizes on the stress distribution in the acetabulum. The idealized 2-D models showed reasonable agreement when compared quantitatively with the in vitro study.

Introduction: Fragility of the bone is widely regarded as a cause of Colles’ Fracture particularly in middle aged or elderly women[1]. However not every fall results in fracture of the wrist. The normal volar angle of the distal radius is said to be about 10 degrees although in one study the mean volar angulation was found to be 12 degrees with a range from 4 to 23 degrees[2]. We hypothesised that the volar angle of the distal radius or the position of the wrist at impact could affect where the peak stresses occurred during a fall onto the outstretched arm. We investigated the effect of these two variables on the location and magnitude of the peak stresses using finite element analysis.

Materials and Method: A finite element model of the distal radius was constructed in MARC (MSC software, USA). The model was developed from CT data of the right wrist of a 46 year old male. The data was examined by edge detection software (Materialise, Belgium). The inner and outer boundaries of the cortex were imported as curves into MARC. A surface mesh of the distal radius was constructed, from which a 3D solid mesh of the distal radius was generated automatically. The volar angle was modified to represent between 5 to 25 degrees in 5 degree increments. The wrist position was also changed for each volar angle. This varied in 5 degree increments from 0 to 35 degrees, and then at 45, 75 and 90 degrees. Material properties assigned to cortical and cancellous bone were 20GPa and 6GPa respectively with a Poisson’s Ratio of 0.3. The model consisted of 17660 8 noded hexahedral elements and was fully fixed at the cut end of the proximal radius. For each volar angle a load of 500N and 400N was applied perpendicularly to the articular surface across the scaphoid and lunate fossa respectively. The magnitude and location of peak stresses in the proximal and distal radius were recorded.

Results: Results show that the location and magnitude of peak stresses vary as a result of wrist position. Distally the stress rises with increasing dorsiflexion and at 35 degrees exceeds the load to failure. The volar angle does not influence the stresses unless it is 20 degrees or more. Proximally the volar angle had no effect, but if the wrist is in more than 75 degrees of dorsiflexion then the peak stresses exceeded the load to failure.

Conclusion: Results show that a fall onto the outstretched arm will produce differential stresses in the radius depending on the position of the wrist at impact. The volar angle affected the stresses in the distal radius at greater than 20 degrees but proximally it did not. Proximally stresses above 130MPa (when the wrist is in more than 75 degrees of dorsiflexion) will subject the wrist to fracture[3]. Distally (when the wrist is in more than 35 degrees of dorsiflexion) with high volar angles (greater than 20 degrees) is likely to produce the conditions for a fracture (cancellous bone has been reported to fail as a result of fracture at 50 MPa [4] and for osteoporotic bone at 0.44MPa [4].

The restoration of pain-free stable function in gleno-humeral arthritic cases in various situations such as rotator cuff deficiency, old trauma and failed total shoulder arthroplasty is a challenging clinical dilemma. The Bayley-Walker shoulder has been designed specifically for very difficult cases where surface replacement devices do not provide sufficient stability. This device is a fixed-fulcrum reversed anatomy prosthesis consisting of a titanium glenoid component with a CoCrMo alloy head that articulates with an UHMWPE liner encased in a titanium alloy humeral component that has a long tapered grooved stem. The centre of rotation of the Bayley-Walker shoulder is placed medially and distally with respect to the normal shoulder in order to improve the efficiency of the abductor muscles. An important problem in devices of this type is obtaining secure and long-lasting fixation of the glenoid component. The glenoid component relies on fixation through the cortical bone by using threads, which protrude through the anterior surface of the scapula at the vault of the glenoid. It is HA coated for subsequent osseointegration. The purpose of this study was to investigate fixation of the glenoid component.

A 3D finite element model of the glenoid component implanted in a scapula was analysed using Abaqus. The implant was placed in position in the scapula, with the final 2–3 screw threads cutting through the cortical bone on the anterior side at the vault of the glenoid due to the anatomy in this region. The analysis was performed for two load cases at 60° and 90° abduction. A histological study of a retrieval case, obtained 121 days after implantation, was also conducted.

The FEA results showed that most of the forces were transmitted from the component to the cortical bone of the scapula, the remaining load being transmitted through cancellous bone. In particular the area where the threads of the glenoid component penetrated the scapula showed high strain energy densities. Histology from the retrieved case showed evidence of bone remodelling whereby new bone growth resulting in cortical remodelling had occurred around the threads.

Both the FEA and histological study show that fixing the component at multiple locations in cortical bone may overcome the problems of glenoid loosening associated with constrained devices. The Bayley-Walker device has been used on a custom basis since 1994; 81 Bayley–Walker shoulders for non-tumour conditions and 43 Bayley-Walker glenoid components have been used in association with a bone tumour implant, with good early results. Radiographically, radiolucencies have not been observed and overall the comparisons with the original Kessel design are positive.